by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a Jos Huntington Beach Fax: +1 714-899-8179 Website : wwwairtech.com
INTERNATIONAL INC. (CA92647 USA
Data Sheet DAHLAR RELEASE BAG 125
Economical vacuum bag with excellent release properties
fH CDESCRIPTION
Dahlar Release Bag 125 is an economical film designed for both vacuum bagging and release applications. It
can be used for cures up to 285 F (140 C) and will release from most resins associated with aerospace, marine,
and recreational products. This formulation has improved tear resistance and elongation over products
previously offered as low temperature, multiple process films.
Dahlar Release Bag 125 (0.001 inch or 25 um) is the ideal release film for polyester or vinyl ester resins as well as
epoxies and phenolics. See the release film section. It is also offered with our embossed, cracked ice pattern
making it a breather, release film and vacuum bag all-in-one.
BENEFITS
+ Reduce inventory cost with economical single choice film option for use as bag or release film.
+ Tough, strong, and good elongation make bagging much easier than with other low cost products.
+ Embossed version makes compaction and debulking faster and cheaper.
f@ TECHNICAL DATA
Test method
Material type Polyolefin, multi-layer
Elongation at break 400 % ASTM D 882
Tensile strength 9400 psi (65 MPa) ASTM D 882
Maximum use temperature 285 F (140 C)
Materials to avoid Compatible with most resin systems
Color Green
Shelf life Unlimited when stored in original packaging at 72 F (22 C)
@ SIZES
ANC eerie ae Forms Available
from 0.001 to 0.003 inch (25 – 75 um) up to 260 inches (6.6 m) SHT, CF, LFT
from 0.002 to 0.003 inch (50 – 75 um) up to 157 inches (4.0 m) SHT (Embossed Film)
+ For more sizes, see the Commonly Used Sizes chart in this section.
+ Custom shapes and sizes are available, please contact Airtech for more information.
< Siit
Open Edge
*SHT=Sheeting CF=Centerfold LFT=Lay-Flat GT=Gusseted G=Gusseted
Tubing Tubing
@ NOTES
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
+ Watch a demo video of Dahlar Release Bag 125 in the "Media Center" on our website.
Last updated : 2020-05-26
Catalog position : Bagging films a
-Asthe conditions ormethed of se ncding storage, ae byond ou conto Antec tematlonl nc. does not assume ay responsi forth pesomnanc fit mate fr ny pat. The tes sds.
itech ntemationa ic dls and buyer wes aan sl pid warrants cudng without baton the pied wanes of mechan neo finer prc ese The nro conte erin
represents ypc properties and shoul ot be ed for specication purposes, Ay tansaton prove for you Convenience ny. The ofa language Engith andthe ecw Catoma USA
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a Jos Huntington Beach Fax: +1 714-899-8179 Website : wwwairtech.com
INTERNATIONAL INC. (CA92647 USA
Data Sheet DAHLAR RELEASE BAG 125
Economical vacuum bag with excellent release properties
fH CDESCRIPTION
Dahlar Release Bag 125 is an economical film designed for both vacuum bagging and release applications. It
can be used for cures up to 285 F (140 C) and will release from most resins associated with aerospace, marine,
and recreational products. This formulation has improved tear resistance and elongation over products
previously offered as low temperature, multiple process films.
Dahlar Release Bag 125 (0.001 inch or 25 um) is the ideal release film for polyester or vinyl ester resins as well as
epoxies and phenolics. See the release film section. It is also offered with our embossed, cracked ice pattern
making it a breather, release film and vacuum bag all-in-one.
BENEFITS
+ Reduce inventory cost with economical single choice film option for use as bag or release film.
+ Tough, strong, and good elongation make bagging much easier than with other low cost products.
+ Embossed version makes compaction and debulking faster and cheaper.
f@ TECHNICAL DATA
Test method
Material type Polyolefin, multi-layer
Elongation at break 400 % ASTM D 882
Tensile strength 9400 psi (65 MPa) ASTM D 882
Maximum use temperature 285 F (140 C)
Materials to avoid Compatible with most resin systems
Color Green
Shelf life Unlimited when stored in original packaging at 72 F (22 C)
@ SIZES
ANC eerie ae Forms Available
from 0.001 to 0.003 inch (25 – 75 um) up to 260 inches (6.6 m) SHT, CF, LFT
from 0.002 to 0.003 inch (50 – 75 um) up to 157 inches (4.0 m) SHT (Embossed Film)
+ For more sizes, see the Commonly Used Sizes chart in this section.
+ Custom shapes and sizes are available, please contact Airtech for more information.
< Siit
Open Edge
*SHT=Sheeting CF=Centerfold LFT=Lay-Flat GT=Gusseted G=Gusseted
Tubing Tubing
@ NOTES
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
+ Watch a demo video of Dahlar Release Bag 125 in the "Media Center" on our website.
Last updated : 2020-05-26
Catalog position : Bagging films a
-Asthe conditions ormethed of se ncding storage, ae byond ou conto Antec tematlonl nc. does not assume ay responsi forth pesomnanc fit mate fr ny pat. The tes sds.
itech ntemationa ic dls and buyer wes aan sl pid warrants cudng without baton the pied wanes of mechan neo finer prc ese The nro conte erin
represents ypc properties and shoul ot be ed for specication purposes, Ay tansaton prove for you Convenience ny. The ofa language Engith andthe ecw Catoma USA
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a Jos Huntington Beach Fax: +1 714-899-8179 Website : wwwairtech.com
INTERNATIONAL INC. (CA92647 USA
Data Sheet DAHLAR RELEASE BAG 125
Economical vacuum bag with excellent release properties
fH CDESCRIPTION
Dahlar Release Bag 125 is an economical film designed for both vacuum bagging and release applications. It
can be used for cures up to 285 F (140 C) and will release from most resins associated with aerospace, marine,
and recreational products. This formulation has improved tear resistance and elongation over products
previously offered as low temperature, multiple process films.
Dahlar Release Bag 125 (0.001 inch or 25 um) is the ideal release film for polyester or vinyl ester resins as well as
epoxies and phenolics. See the release film section. It is also offered with our embossed, cracked ice pattern
making it a breather, release film and vacuum bag all-in-one.
BENEFITS
+ Reduce inventory cost with economical single choice film option for use as bag or release film.
+ Tough, strong, and good elongation make bagging much easier than with other low cost products.
+ Embossed version makes compaction and debulking faster and cheaper.
f@ TECHNICAL DATA
Test method
Material type Polyolefin, multi-layer
Elongation at break 400 % ASTM D 882
Tensile strength 9400 psi (65 MPa) ASTM D 882
Maximum use temperature 285 F (140 C)
Materials to avoid Compatible with most resin systems
Color Green
Shelf life Unlimited when stored in original packaging at 72 F (22 C)
@ SIZES
ANC eerie ae Forms Available
from 0.001 to 0.003 inch (25 – 75 um) up to 260 inches (6.6 m) SHT, CF, LFT
from 0.002 to 0.003 inch (50 – 75 um) up to 157 inches (4.0 m) SHT (Embossed Film)
+ For more sizes, see the Commonly Used Sizes chart in this section.
+ Custom shapes and sizes are available, please contact Airtech for more information.
< Siit
Open Edge
*SHT=Sheeting CF=Centerfold LFT=Lay-Flat GT=Gusseted G=Gusseted
Tubing Tubing
@ NOTES
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
+ Watch a demo video of Dahlar Release Bag 125 in the "Media Center" on our website.
Last updated : 2020-05-26
Catalog position : Bagging films a
-Asthe conditions ormethed of se ncding storage, ae byond ou conto Antec tematlonl nc. does not assume ay responsi forth pesomnanc fit mate fr ny pat. The tes sds.
itech ntemationa ic dls and buyer wes aan sl pid warrants cudng without baton the pied wanes of mechan neo finer prc ese The nro conte erin
represents ypc properties and shoul ot be ed for specication purposes, Ay tansaton prove for you Convenience ny. The ofa language Engith andthe ecw Catoma USA
by | Sep 27, 2025
TECHNICAL DATA SHEE T
VAC-PAK
HS8171
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VBHS8171_02.21_Issue1
VAC-PAK
HS8171
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
A clear green, heat stabilized blown nylon 6 film.
Excellent tensile strength and heat ageing
properties, having been successfully used at
pressures of 100PSI (6.9bar) and temperatures of up
to 204 C (400 F).
Approved on various aerospace specifications.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Clear green
Tensile strength at break (ASTM D882) 96MPa 14000PSI
Elongation at break (ASTM D882) 415%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45kg Up to 100lbs
Widths Up to 4.06m (open) Up to 460in (open)
Formats available Tube, sheet, V sheet
STORAGE
Vac-Pak HS8171 is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of
use is therefore an important factor for successful performance. All nylon films absorb water. The higher the moisture
content the more flexible they become. Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
VACUUM BAGGING FILM
VAC-PAK” HS8171
Vacuum bagging film .
Ideally suited to aerospace applications
Features and Benefits
e Aclear green, heat stabilized blown nylon 6 film. e Approved on various aerospace specifications.
e Excellent tensile strength and heat ageing
properties, having been successfully used at
pressures of 100PSI (6.9bar) and temperatures of up
to 204 C (400 F).
PROPERTIES
Maximum use temperature 204 C 400 F
Color Clear green
Tensile strength at break (ASTM D882) 96MPa 14000PSI |
Elongation at break (ASTM D882) 415%
Yield 50ym: 17.30m/kg 9.39yd”/Ib
75pm: 11.60m7/kg 6.3yd7/lb
AVAILABILITY
Thickness 50 and 75ym 0.002 and 0.003in {
Roll weight Up to 45kg Up to 100Ibs
Widths Up to 4.06m (open) Up to 460in (open)
Formats available Tube, sheet, V sheet ‘
STORAGE
Vac-Pak HS8171 is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of
use is therefore an important factor for successful performance. All nylon films absorb water. The higher the moisture
content the more flexible they become. Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Solvay does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy,
the completeness or the relevance of the date and information set out herein, Because the properties of this product can be significantly affected by the
fabrication and testing techniques employed, and since Solvay does not control the conditions under which its products are tested and used, Solvay cannot
guarantee the properties provided will be obtained with other processes and equipment. No guaranteo or warranty is provided if the product is adapted for a
specific use or purpose. Solvay declines any liability with respect to the use made by any third patty of the data and infermation contained herein. Solvay
has the right to change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2017, Soivay. All
rights reserved,
Solvay
Composite Materials HO
4500 McGinnis Ferry Rd f so LVAY
Alpharetta, GA 30005-3914 USA asking mare from chemistry?
24 March 2013
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
i Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
y a ea CA92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 65R
The all purpose hose for composites, bonding and tool shops
DESCRIPTION
Airflow 65R can be used as an autoclave or oven hose. The outer ply is silicone rubber that encases a flexible steel
tube that prevents collapse and hose separation. The bell-shaped ferrule helps hose lacerations at fitting ends
extending hose life.
@ BENEFITS
+ Safer vacuum for part curing with heavy duty hose construction.
+ Flexibility make loading ovens and autoclaves easy and fast.
+ Straight and elbow end fittings help reduce strain on hose and vacuum bags.
M TECHNICAL DATA
Material type of inner tube Interlocking steel tube
Material type of hose Silicone rubber
Hose colour Green
End fitting 1/4 inch male NPT
Service temperature 232 C (450 F)
Max autoclave pressure 9 bar (130 psi)
SIZES
) Product Reference. |. Nominal Outer Hose Diameter Available Length
AIRFLOW 65R 19 mm (3/4 inch) up to 30 m (100 feet)
+ Though standard sizes are 3 m (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
1/4 in. male NPT straight end fittings on one or both ends.
oR
ns
z A
BlAri
1/4 in. male NPT 90 fixed end fittings on one or both ends.
Last updated : 2024-06-11
Catalog position : Vacuum valves and hoses
ste condion or metodo nig Hoge beynd ut canto tech nema cdot tae repeat fete proms th me ony parc we. Te tert Aste temo oe
cima wen anand al ple waa ndng wht ato henge wri of meando ee for parca The rmation crane sr yl opera dnt eed
petaton purpose Any taronk poet yu convener oy Tne ealungunge gn anh fel am Catena SA
by | Sep 27, 2025
Holcim Solutions and Products US, LLC
1-800-878-7876 www.holcimtacky-tape.com
TECHNICAL DATA SHEET
PRODUCT DESCRIPTION:
TACKY TAPE
SM5126 is a pressure sensitive sealant tape, in roll
form that is designed to adhere various bagging films to platen
surfaces. It has been successfully used with silicone blankets,
nylon and PVC films. Compatibility and tenacious adhesion are
evidenced on a variety of tool surfaces. Typical cure cycle
temperatures requiring a positive bag seal from ambient room
temperature to 450 F (232 C) are easily accommodated.
ADVANTAGES:
Easy to apply by hand (User friendly)
TYPICAL PROPERTIES:
Ideal for oven or autoclave cure
Room temperature to 450
o
F (232
o
C) cure cycles
Strips clean from various tools surfaces
Tenacious adhesion to nylon films and tool surfaces
Non-Hazardous and thermally stable
APPLICATION:
Apply by hand to a clean dry tool or platen with release paper on
top. When the sealant is in position remove the release paper
and lay the film on top. Apply pressure by hand or roller on the
sealant to obtain maximum adhesion and to ensure positive
vacuum. It is recommended to strip below 150
o
F (66
o
C) to
minimize or reduce the parts from becoming warped. SM 5126
can be stripped without leaving a residue on metal tool surfaces
that have been cooled to room temperature.
PERFORMACE TEMPERTAURE RANGE:
Application Temperature Range: 45 F (7 C) to 120 F (49 C)
Service Temperature Range: Room temp. to 450 F (232 C)
PACKAGING:
Tacky Tape
SM5126 sealant is supplied in roll form with a
special release paper. Several standard tape dimensions are
available. This product is available through Holcim Solutions
and Products US, LLC. Customer Service department at 1-800-
878-7876.
Complete technical information is available from
Holcim Solutions and Products US, LLC
03/2023
SM5126
VACUUM BAG SEALANT TAPE
EXCLUSION OF WARRANTIES:
INSTALL AS DIRECTED ON TACKY-TAPE PRODUCT DATA SHEET. USER
DETERMINES SUITABILITY FOR INTENDED USE AND ASSUMES ALL RISK
AND LIABILITY. THIS PRODUCT IS SOLD AS IS. EXCEPT AS REQUIRED BY
LAW, THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING,
WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. IF TERMS ARE NOT ACCEPTABLE, RETURN
UNOPENED PRODUCT TO PLACE OF PURCHASE. DAMAGES IN EXCESS OF
THE PURCHASE PRICE OF THESE PRODUCTS.
COLOR: Dark Gray
PERCENT SOLID: 100%
CONSISTENCY: Cone
Penetration
80 – 90
300 GRAM LOAD
ASTM D-217
WEIGHT/GALLON: 10.73 LBS/GALLON (1.28 Kg/L)
FREIGHT CLASSIFICATION: Caulking Compound, NOIBN (NO
LABEL REQUIRED)
STORAGE: Keep in cool dry place. Tacky
Tape
SM5126 has a 14 month
shelf life from date of
manufacture when stored at or
below 80
o
F (27
o
C). Do not store
cartons on end, keep flat.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
QUICKDRAW HS8171
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS QDHS8171_02 .21_Issue1
QUICKDRAW HS8171
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Unique film, embossed to allow air evacuation in
compaction or de-bulk vacuum bagging processes,
without the need for breather fabric or release film.
A clear green, heat stabilized, co-extruded, co-
polymer film, produced from a modified nylon resin.
Capable of withstanding operating temperatures up to
204 C (400 F), providing sufficient temperature
resistance to withstand most common resin
exothermic reactions.
Approved on various aerospace specifications and
used extensively within the industry.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Clear green
Tensile strength at break (ASTM D882) 96MPa 14000PSI
Elongation at break (ASTM D882) 415%
Yield 11.3m /kg 55.33ft /lb
AVAILABILITY
Thickness 75 m 0.003in
Roll weight Up to 50kg Up to 110lbs
Formats available Sheet
STORAGE
Quickdraw HS8171 is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of
use is therefore an important factor for successful performance. All nylon films absorb water. The higher the moisture
content the more flexible they become. Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
#’ lan Huntington Beach Fax: +1 714-899-8179 Website : www.airtech.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet AHTC-1000 QTD
High temperature, all metallic, quick turn disconnect
i =DESCRIPTION
The AHTC-1000 QTD Quick Turn Disconnect is designed for use up to 1000 F (538 C). The ferrule expands to
create a seal at elevated temperatures. There are no organic materials to break down under high temperature
applications. The end fittings are female NPT style and work well with our Vac Valve 409 SS HTR, Airflow 800, and
BBH 1080 autoclave hoses.
Mi BENEFITS
+ Standard thread design compatible with Vac Valves and Hoses.
+ Highest temperature and pressure resistance for high end applications.
+ Highly durable construction for long in-service life.
fl TECHNICAL DATA
Material type All metallic
Connection to hose Threaded
Screw thread 1/2 or 1/4 inch female NPT
Service temperature 1000 F (538 C)
Maximum autoclave pressure 1000 psi (69 bar)
@ SIZES
Female threaded AHTC-1000 QTD
ey,
{ S
lM NOTES
+ Available upon request only. Minimum order may apply.
Last updated : 2016-02-03
Catalog position : Vacuum valves and hoses s 7
As thecondtion ormethods of ncing stag, ae beyond our contol Aitech ntetiona ne. dos not ase any esponeblty fr the peormance of his mate ay paw The mates sod”
itech nteratonal ne dics and buyer wes ny and imped warontes, Inching without bration te mpled wararte etait 2 et ft parr. The ermaton contd er
represents pal properties and shoud net be ed fr speation pupose- Ary Vonation ls prove oyu convenience ony. The oficial guage Engh andthe fal aw Cairn SA
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
fF Ls CA 92647 USA
INTERNATIONAL INC.
Data Sheet PE TUBE & SPIRAL TUBE
Low temperature tubing for resin infusion
lM DESCRIPTION
PE tube is a low temperature tube designed to transport resin during infusion. PE spiral tube can be used to create a
vacuum manifold around the perimeter of a part during infusion.
@ TECHNICAL DATA
Material type Polyethylene
Colour Transparent
Maximum use temperature 250 F (121 C)
M@ SIZES
PE Tubing
Outer Diameter (0.D.) Internal Diameter (|.D.)
PT1/2 1/2″ 3/8″ 330 feet
PT5/8 5/8″ 1/2″ 330 feet
PT3/4, 3/4″ 5/8″ 330 feet
PE Spiral
Outer Diameter (0.D.) Internal Diameter (I.D.)
Psw3/8 3/8″ 1/4″ 330 feet
Psw1/2 1/2″ 3/8″ 330 feet
Psws/8 5/8″ 1/2″ 330 feet
Psw3/4 3/4″ 5/8″ 330 feet
,
? –
PE Tubing PE Spiral Tubing
M@ NOTES
+ The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
+ See Resin Infusion Connectors technical data sheet for compatible fittings.
+ Example: 3/8″ |.D. PE Tube works with NEF 38.
Last updated : 2023-07-20
Catalog position : Resin infusion products
at emt orth i cig rn on Aichi doe nr egy thon ftir iy prereset be
