by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a Huntington Beach Fax: +1 714-899-8179 Website : www.airtech.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet DAHLVAC MB80
Vacuum manifold for resin infusion
DESCRIPTION
Dahlvac MB80 is an easy to use vacuum source designed for resin infusion. The product can easily be attached
to the periphery of a mold using Airtac 2 Improved spray adhesive or Airhold 10 CBS double backed tape. The
internal spiral tube provides good vacuum flow and the outer layer of Dahltexx SP-2 allows breathability while
preventing resin from entering the vacuum channel.
@ BENEFITS
+ Easy to use and simplifies the infusion process.
. Highly breathable while preventing resin from entering the vacuum source.
+ Attaches easily to the mold using Airtac 2 Improved or Airhold 10 CBS double backed tape.
+ Aids in uniform resin distribution.
@ TECHNICAL DATA
Material type Dahltexx SP-2 fabric with PE Spiral Wrap
Color Blue
Maximum recommended use temperature 250 F (121 C)
@ SIZES
2.0 inches (5.08 cm) 100 feet (30.48 m)
< ef Ne es, F; - ; :
by | Sep 27, 2025
5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
y a Huntington Beach Fax: +1 714-899-8179 Website : www.airtech.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet DAHLVAC MB80
Vacuum manifold for resin infusion
DESCRIPTION
Dahlvac MB80 is an easy to use vacuum source designed for resin infusion. The product can easily be attached
to the periphery of a mold using Airtac 2 Improved spray adhesive or Airhold 10 CBS double backed tape. The
internal spiral tube provides good vacuum flow and the outer layer of Dahltexx SP-2 allows breathability while
preventing resin from entering the vacuum channel.
@ BENEFITS
+ Easy to use and simplifies the infusion process.
. Highly breathable while preventing resin from entering the vacuum source.
+ Attaches easily to the mold using Airtac 2 Improved or Airhold 10 CBS double backed tape.
+ Aids in uniform resin distribution.
@ TECHNICAL DATA
Material type Dahltexx SP-2 fabric with PE Spiral Wrap
Color Blue
Maximum recommended use temperature 250 F (121 C)
@ SIZES
2.0 inches (5.08 cm) 100 feet (30.48 m)
< ef Ne es, F; - ; :
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP/200TFP-1
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP/200TFP-1_02.21_Issue1
200TFP/200TFP-1
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
200TFP-1 especially useful where tolerances do not
allow for a heavier material.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 200TFP
Fabric weight 200TFP-1
53 – 75g/m
46g/m
1.8 – 2.1oz/yd
1.36oz/yd
Release coating PTFE
AVAILABILITY
Standard width 200TFP
Standard width 200TFP-1
Up to 2m
0.97m
Up to 80in
38in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFP_02.21_Issue1
200TFP
Release fabric
Ideally suited to flat and simple contour applications
Features and Benefits
Porous PTFE-coated plain weave fiberglass cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will release from all commercial resin systems.
Ideal for flat and simple contoured assemblies.
Designed to allow excess resin, volatiles and trapped
air to bleed through the release fabric and be
absorbed in the breather, or vented out of the bag
through the vacuum vent port.
Can be used on metal-bond assemblies to allow the
adhesive flash to be bled into the breather and
removed from the assembly.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Beige
Fabric type Fiberglass
Fabric weight 53 – 75g/m 1.8 – 2.1oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
200TFNP
RELEASE FABRIC
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS 200TFNP_02.21_Issue1
200TFNP
Release fabric
Ideally suited to metal-bond applications
Features and Benefits
Non-porous PTFE-coated plain weave fiberglass
cloth.
Resistant to all solvents, adhesives and resin
systems normally encountered in composite and
metal-bond manufacture.
Will contain resin and be readily released from all
commercial resin systems.
Designed as a release fabric which will prevent resin
from bleeding through the release fabric and into the
breather fabric.
Can be used on metal-bond assemblies to promote
filleting of the adhesive flash.
Ideal for flat and simple contoured assemblies.
PROPERTIES
Maximum cure temperature 288 C 550 F
Color Tan
Fabric type Fiberglass
Fabric weight 109g/m 3.2oz/yd
Release coating PTFE
AVAILABILITY
Standard width Up to 1.52m Up to 60in
Standard length Up to 91m Up to 100yd
Slit widths available
STORAGE
No special storage conditions required.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
