by | Sep 27, 2025
TECHNICAL DATA 3/10/2011
12801 Ann Street, Santa Fe Springs, California 90670 TEL 562-906-3300 FAX 562-941-9505
-85-
VAC-PAK IS A REGISTERED TRADEMARK OF RICHMOND AIRCRAFT PRODUCTS INC.
NOTE: DATA PROVIDED IS FOR INFORMATION ONLY AND DOES NOT CONSTITU TE ANY WARRANTY FOR THE PRODUCT. AS THE CONDITIONS AND VARYING
METHODS OF USE ARE BEYOND OUR CONTROL, RI CHMOND AIRCRAFT PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENT AL,
OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVE NUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE, OR INABIL ITY
TO USE THESE MATERIALS. THESE MATERIALS ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDI NG,
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Fluoropolymer Insulated
TE WIRE & CABLE – AUTOCLAVE THERMOCOUPLE
Applications
Autoclaves
Composites
Cryogenics
Food and Drug
Biotech
Laboratory
Automotive
Environmental Chambers
Product Features
Labor Saving Patented*** Thermo-
couple Assembly
Reduced Vacuum Leakage
Molded-on Connector Rated to
500 F (260 C)
Small Diameter
High Accuracy
Small Thermal Mass
Excellent Chemical
Resistance
Available Options
Mini connector Rated to 250 F (121 C)
Available as Bulk Wire
High Temperature Braided Insulations for 950 F (510 C) to 2200 F
(1204 C)
Special Color Codes
Certification to BAC 5621
Calibration Test Reports
Product Specifications
Conductors:
Solid thermocouple wire per ASTM E230 & ANSI MC96.1
Insulation:
Flame Retardant extruded
Fluoropolymer FEP or PFA
Construction:
Overall insulation encapsulating parallel conductors
Operating Temperature:
FEP -328 F (-200 C) to + 400 F (+200 C) continuous
PFA -328 F (-200 C) to 500 F (+260 C) continuous
Limits of Error:
Conforms to ASTM E230, IEC 584 and ANSI MC 96.1
Color Code:
Varies with insulation type
TECHNICAL DATA 3/10/2011
12801 Ann Street, Santa Fe Springs, California 90670 TEL 562-906-3300 FAX 562-941-9505
-86-
VAC-PAK IS A REGISTERED TRADEMARK OF RICHMOND AIRCRAFT PRODUCTS INC.
NOTE: DATA PROVIDED IS FOR INFORMATION ONLY AND DOES NOT CONSTITU TE ANY WARRANTY FOR THE PRODUCT. AS THE CONDITIONS AND VARYING
METHODS OF USE ARE BEYOND OUR CONTROL, RI CHMOND AIRCRAFT PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENT AL,
OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVE NUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE, OR INABIL ITY
TO USE THESE MATERIALS. THESE MATERIALS ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDI NG,
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Nominal Weights and Dimensions Fluoropolymer Autoclave Thermocouple Wire
Conductor Size Insulation Thickness Outer Diameter Bulk Wire Net Weight
AWG (MM) Inches (MM) Inches (MM) LB/MF (KG/KM)
20 (0.81) .015 (.38) .065 x .115 (1.7 x 2.9) 10.9 (16.2)
22 (0.64) .010 (.25) .045 x .090 (1.1 x 2.3) 5.8 (8.6)
24 (0.51) .010 (.25) .040 x .080 (1.0 x 2.0) 4.4 (6.5)
26 (0.41) .010 (.25) .036 x .072 (.91 x 1.8) 3.2 (4.8)
28 (0.32) .010 (.25) .032 x .066 (.81 x 1.7) 2.5 (3.7)
These economical, ready to use, patented*** AUTOCLAVE THERMOCOUPLE have a unique design character-
istics which reduce vacuum leakage during use. The key to the effectiveness of the encapsulated AUTOCLAVE
THERMOCOUPLE is its unique, proprietary, single extrusion thermocouple wire with molded-on connector con-
struction, which virtually eliminates leakage. The construction consists of special grade limits of error thermocou-
ple wire with a welded junction and permanently molded, high temperature standard size connector (miniature
molded connectors are available).
AUTOCLAVE THERMOCOUPLES are available in a wide variety of lengths, conductor sizes and insulation ma-
terials. Calibration Type J, K, T and E thermocouples are available.
Standard insulation materials, including FEP, PFA, polyimide tape, and B-Fiber/Glass (synthetic polyamide fiber
blend with a fiberglass outer jacket), provide extensive operating temperature ranges to fit a wide variety of appli-
cations. Other insulations with temperature ratings up to 2200 F (1204 C) are available (molded connector is lim-
ited to lower rated operating temperature).
Every unit is tested for circuit integrity and correct polarity. In addition, AUTOCLAVE THERMOCOUPLE meets
MIL-STD-105 Sampling Procedure for Inspection and MIL-I-45208A Inspection System Requirements.
The products referenced above represent the most popular constructions. Other constructions can be manufactured
to meet individual specification and application requirements. Contact us for additional information.
Thermocouple
Type
Grade
Designation
Tolerance-Reference Junction 32 F (O C)
Special Grade Limits
F ( C) whichever is greater
Thermocouple Wire
T TT +0.9 (0.5) or 0.4%
J JJ +2 (1.1) or 0.4%
E EE +1.8 (1) or 0.4%
K KK +2 (1.1) or 0.4%
T* Cryogenic Range TT* +0.9 (0.5) or 0.8%**
* Thermocouple material is normally supplied to meet tolerances above 0 C (32 F). If material is required to meet
Tolerances below 0 C (32 F), the purchase order must so state. Special selection of material is required.
**
***
Suggested initial calibration tolerance. Requirements should be discussed between purchaser and supplier.
Patented by TE Wire and Cable.
Table 1
Initial Calibration Tolerances Per ASTM E230 and ANSI MC96.1
by | Sep 27, 2025
ow
Richmond
Aircraft Products
TECHNICAL DATA 3/24/2008
High Temperature Double Backed Tape
DESCRIPTION:
RAP HOLD 1 is a .001″ polyester film coated on both sides with a
solvent resistant acrylic adhesive. For use at temperatures up to 400 F
(205 C).
APPLICATION:
RAPHOLD 1 performs excellent in resin dam hold down, inter-
bagging seal or for any place where a two-sided general purpose tape
is needed.
a
PHYSICAL PROPERTIES
Film Substrate: Polyester
Color: Clear
Adhesive: Acrylic
Total Thickness .004″ (10mm)
MECHANICAL PROPERTIES:
Tensile: 25 Ibs/in. wide 11.2Kg/ 25.4mm wide
Elongation: 100%
Adhesion: 35 oz/in. width 99K g/25.4mm wide
a
Standard size: 1″ x 36 yards 25.4mm x 33m.
Other widths available upon special order…
NOTE: DATA PROVIDED IS FOR INFORMATION ONLY AND DOES NOT CONSTITUTE ANY WARRANTY FOR THE PRODUCT. AS THE CONDITIONS AND VARYING
ETHODS OF USE ARE BEYOND OUR CONTROL, RICHMOND AIRCRAFT PRODUCTS, INC. SHALL NOT BE LIABLE FOR ANY SPECIAL, INDIRECT. INCIDENTAL
OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS, WHICH MAY RESULT FROM THE USE. OR INABILITY
7G Use THESE MATERIALS. THESE MATERIALS ARE PROVIDED AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
43503 Pumice Street, Norwalk, California 90650 – TEL 562-404-2440 – FAX 562-404-9011
-46-
by | Sep 27, 2025
Cytec oft Vac-Pak HS 8171 6/66
Process Materials Vacuum bagging film
Vac-Pak HS 8171 6/66
Features
Heat stabilised, co-extruded co-polymer film Ideal for advanced composite fabrication and other
produced from modified nylon resin. high temperature/pressure applications when softness
High temperature film which can be used for cures up and workability are essential.
to 204 C (400 F) and remains pliable after extended Can be heat seamed to meet any customer shape
cure cycles. requirements.
The co-extrusion process combines multiple layers of
resin flow into film prior to exiting the extrusion die.
This process represents the most advanced state of
the art technology in blown film production.
Maximum use temperature 204 C 400 F
Color Clear, blue and green
Tensile strength at break 103MPa 15000PS!
(ASTM D882)
Elongation at break (ASTM 400%
D882)
Yield SOum: 17.30m?/kg 9.39yd/Ib
75pm: 11.60m?/kg 6.3yd?/Ib
Thickness 50 and 75um 0.002 and 0.003in
Roll weight Up to 45kg Up to 100Ibs
Widths Up to 4m (open) Up to 160in (open)
Formats available V sheet, sheet, lay flat tube
Do not store rolls vertically on their ends.
Handling of these products must conform to individual company guidelines and health and safety regulations.
Anon cota bmn donner cand hs he en nod nd an et ened eet Scale ern. They
{cap = rece Mr ey a Cpr ou nr CA Cte Pace a en So ss Me lA ifs wera
DELIVERING TECHNOLOGY BEYOND OUR CUSTOMERS IMAGINATION CYTEC
Aerospace Materials | Industrial Materials | Process Materials
21 March 203
by | Sep 27, 2025
TECHNICAL DATA SHEE T
VAC-PAK
HS 8171 6/66
PREPREG
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VBHS81716/66_02.21_Issue1
VAC-PAK
HS 8171 6/66
Vacuum bagging film
Ideally suited to high temperature and pressure applications
Features and Benefits
Heat stabilised, co- extruded co-polymer film
produced from modified nylon resin.
High temperature film which can be used for cures
up to 204 C (400 F) and remains pliable after
extended cure cycles.
The co-extrusion process combines multiple layers of
resin flow into film prior to exiting the extrusion die.
This process represents the most advanced state of
the art technology in blown film production.
Ideal for advanced composite fabrication and other
high temperature/pressure applications when softness
and workability are essential.
Can be heat seamed to meet any customer shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Clear, blue and green
Tensile strength at break (ASTM D882) 103MPa 15000PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45kg Up to 100lbs
Widths Up to 4m (open) Up to 160in (open)
Formats available V sheet, sheet, lay flat tube
STORAGE
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
VAC-PAK
HS 8171 6/66
PREPREG
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VBHS81716/66_02.21_Issue1
VAC-PAK
HS 8171 6/66
Vacuum bagging film
Ideally suited to high temperature and pressure applications
Features and Benefits
Heat stabilised, co- extruded co-polymer film
produced from modified nylon resin.
High temperature film which can be used for cures
up to 204 C (400 F) and remains pliable after
extended cure cycles.
The co-extrusion process combines multiple layers of
resin flow into film prior to exiting the extrusion die.
This process represents the most advanced state of
the art technology in blown film production.
Ideal for advanced composite fabrication and other
high temperature/pressure applications when softness
and workability are essential.
Can be heat seamed to meet any customer shape
requirements.
PROPERTIES
Maximum use temperature 204 C 400 F
Color Clear, blue and green
Tensile strength at break (ASTM D882) 103MPa 15000PSI
Elongation at break (ASTM D882) 400%
Yield
50 m: 17.30m /kg
75 m: 11.60m /kg
9.39yd /lb
6.3yd /lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003in
Roll weight Up to 45kg Up to 100lbs
Widths Up to 4m (open) Up to 160in (open)
Formats available V sheet, sheet, lay flat tube
STORAGE
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
STRETCH- VAC 350
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV350_0 2.21_Issue1
STRETCH- VAC
350
Vacuum bagging film
Ideally suited to complex tooling geometry
Features and Benefits
Highly conformable, transparent, co-polymer film
which will remain soft and pliable during cures up to
177 C (350 F).
Suitable for use with complex tooling geometry.
Must be used with suitable high tack sealant tape.
Not recommended for use with polyester or vinylester
resin systems
PROPERTIES
Maximum use temperature 177 C 350 F
Color Clear
Tensile strength at break (ASTM D882) 60MPa 8800PSI
Elongation at break (ASTM D882) 800%
Yield 11.45m /kg 56yd /lb
AVAILABILITY
Thickness 75 m 0.003in
Roll weight Up to 30kg Up to 66lbs
Widths Up to 3.66m (open) Up to 144in (open)
Formats available Sheet and V sheet
STORAGE
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
STRETCH- VAC
TM
3000
Vacuum bagging film, ideally suited to aerospace applications.
Features and Benefits
Multi-layer vacuum baggng film produced using our
state of the art co- extrusion technology.
Suitable for high temperature autoclave curing of
aerospace composites, including BMI resins.
Soft and supple with unprecedented tensile strength
for added security.
Unique formulation less sensitive to low humidity
conditions than standard nylon films. SV 3000 is a
mono-nylon film.
PROPERTIES
Maximum use temperature 204
C 400
F
Color Pink
Density 1.14 g/cm
3
0.65oz/in
3
DSC medium 217
C 422.6 F
Tensile Strength at break (ASTM D882) 96.53 MPa 14,000 psi
Elongation at break (ASTM D882) 475%
Yield for 50 m (0.002 ) 17.4m
2
/kg 9.44 yd
2
/lb
Yield for 75 m (0.003 ) 11.6m
2
/kg 6.29yd
2
/lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003 inches
Roll weight Up to 45 kg Up to 100lbs.
Widths 4.06m (open) 160 inches (open)
Formats available Tube, sheet, V-sheet, gusseted and C-fold
STORAGE, HANDLING AND USE
Nylon based films are sensitive to humidity. A high humidity level will act as plasticizer, making the film more flexible and softer,
while a low humidity level will cause the film to become stiffer.
To preserve the integrity of the materials when stored in their original packaging, it is advisable not to stack more than two pallets.
Do not store rolls on their ends.
STORAGE (RECOMMENDED)
Store the film in a relative humidity (RH) from 25% to 60% and a temperature range of 15 to 40
C (59 to 104 F). Avoid stocking in
RH less than 25% and temperatures less than 10 C (50 F).
USAGE (RECOMMENDED)
If possible use the film in a RH ranging from 50% to 60% and a temperature range of 20 to 25 C (68 to 77 F).
If possible condition the film before handling for 48 hours in the recommended RH and temperature ranges.
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product SDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
STRETCH- VAC
TM
3000
Vacuum bagging film, ideally suited to aerospace applications.
Features and Benefits
Multi-layer vacuum baggng film produced using our
state of the art co- extrusion technology.
Suitable for high temperature autoclave curing of
aerospace composites, including BMI resins.
Soft and supple with unprecedented tensile strength
for added security.
Unique formulation less sensitive to low humidity
conditions than standard nylon films. SV 3000 is a
mono-nylon film.
PROPERTIES
Maximum use temperature 204
C 400
F
Color Pink
Density 1.14 g/cm
3
0.65oz/in
3
DSC medium 217
C 422.6 F
Tensile Strength at break (ASTM D882) 96.53 MPa 14,000 psi
Elongation at break (ASTM D882) 475%
Yield for 50 m (0.002 ) 17.4m
2
/kg 9.44 yd
2
/lb
Yield for 75 m (0.003 ) 11.6m
2
/kg 6.29yd
2
/lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003 inches
Roll weight Up to 45 kg Up to 100lbs.
Widths 4.06m (open) 160 inches (open)
Formats available Tube, sheet, V-sheet, gusseted and C-fold
STORAGE, HANDLING AND USE
Nylon based films are sensitive to humidity. A high humidity level will act as plasticizer, making the film more flexible and softer,
while a low humidity level will cause the film to become stiffer.
To preserve the integrity of the materials when stored in their original packaging, it is advisable not to stack more than two pallets.
Do not store rolls on their ends.
STORAGE (RECOMMENDED)
Store the film in a relative humidity (RH) from 25% to 60% and a temperature range of 15 to 40
C (59 to 104 F). Avoid stocking in
RH less than 25% and temperatures less than 10 C (50 F).
USAGE (RECOMMENDED)
If possible use the film in a RH ranging from 50% to 60% and a temperature range of 20 to 25 C (68 to 77 F).
If possible condition the film before handling for 48 hours in the recommended RH and temperature ranges.
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product SDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
STRETCH- VAC
TM
3000
Vacuum bagging film, ideally suited to aerospace applications.
Features and Benefits
Multi-layer vacuum baggng film produced using our
state of the art co- extrusion technology.
Suitable for high temperature autoclave curing of
aerospace composites, including BMI resins.
Soft and supple with unprecedented tensile strength
for added security.
Unique formulation less sensitive to low humidity
conditions than standard nylon films. SV 3000 is a
mono-nylon film.
PROPERTIES
Maximum use temperature 204
C 400
F
Color Pink
Density 1.14 g/cm
3
0.65oz/in
3
DSC medium 217
C 422.6 F
Tensile Strength at break (ASTM D882) 96.53 MPa 14,000 psi
Elongation at break (ASTM D882) 475%
Yield for 50 m (0.002 ) 17.4m
2
/kg 9.44 yd
2
/lb
Yield for 75 m (0.003 ) 11.6m
2
/kg 6.29yd
2
/lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003 inches
Roll weight Up to 45 kg Up to 100lbs.
Widths 4.06m (open) 160 inches (open)
Formats available Tube, sheet, V-sheet, gusseted and C-fold
STORAGE, HANDLING AND USE
Nylon based films are sensitive to humidity. A high humidity level will act as plasticizer, making the film more flexible and softer,
while a low humidity level will cause the film to become stiffer.
To preserve the integrity of the materials when stored in their original packaging, it is advisable not to stack more than two pallets.
Do not store rolls on their ends.
STORAGE (RECOMMENDED)
Store the film in a relative humidity (RH) from 25% to 60% and a temperature range of 15 to 40
C (59 to 104 F). Avoid stocking in
RH less than 25% and temperatures less than 10 C (50 F).
USAGE (RECOMMENDED)
If possible use the film in a RH ranging from 50% to 60% and a temperature range of 20 to 25 C (68 to 77 F).
If possible condition the film before handling for 48 hours in the recommended RH and temperature ranges.
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product SDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail : airtech@airtechintl.com
y a = Huntington Beach Fax: +1 714-899-8179 Website : www.airtechonline.com
INTERNATIONAL INC. CA 92647 USA
Economical vacuum bagging film
DESCRIPTION
Wrightlon 250Y vacuum bagging film has high elongation, flexibility and tensile strength. The enhanced
physical values allow for added security even in harsh environments. Wrightlon 250Y is well suited for
automotive, marine and other commercial vacuum bagging applications. It is ideal for both autoclave and
oven cures.
@ BENEFITS
+ Wide films save time and money spent seaming film for large parts.
+ Wider films reduce risk of scrap parts due to leakage at seams.
+ Reduce scrap risk due to vacuum loss with high physical properties.
@ TECHNICAL DATA
Test method
Material type Nylon copolymer
Elongation at break 400 % ASTM D 882
Tensile strength 6004.6 psi (41.4 MPa) ASTM D 882
Maximum use temperature 302 F (150 C)
Short term exposure 338 F (170 C)
Flammability (self extinguishing) No ATP-5034
Materials to avoid Strong oxidizers
Color Yellow
Thickness 0.002 inch (50 jam)
Shelf life Unlimited when stored in original packaging at 72 F (22 C)
NOTES
+ Custom shapes and sizes are available, please contact Airtech for more information.
+The maximum use temperature is dependent upon the duration at maximum temperature and is process
specific, Airtech recommends testing prior to use.
Last updated : 2020-11-06
Catalog position : Bagging films
-Asthecondton or methods fuse, lncluing storage, ae beyond our control Altech ternational nc does ot sme any espns fe the performance of his material fo any parca ue. The mater is sld”s
Artec Iteration ne dclsine and buyer wave, any and all imped warts incuding without maton the pled warranties of marcha and of nes fr part useThe foemston contained heen
teptesents ypc properties and should nat be used for specication purposes Any tnsstio provide or yout convenience ony The afi anguages English andthe ofa law Calf, USA
