17FLEX25BD_SDS.pdf

Safety Data Sheet
Issue date 05-Mar-2018 Revision date 29-Mar-2018 Version 2
1. Identification
Product Identifier
Product name Flex Cat 25
Other means of identification
Recommended use of the chemical and restrictions on use
Recommended use No information available.
Application FOR INDUSTRIAL USE ONLY
Details of the Supplier of the Safety Data Sheet
Emergency Telephone Number
Company Phone Number 800-852-3147 (8AM – 5PM EST)
Emergency telephone Chemtrec 1-800-424-9300
2. Hazards Identification
Classification
OSHA Regulatory Status
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Serious eye damage/eye irritation Category 2
Reproductive Toxicity Category 2
Specific target organ toxicity (repeated exposure) Category 2
Label Elements
EMERGENCY OVERVIEW
Precautionary Statements – Prevention
Supplier
CHT
7820 Whitepine Rd
Richmond, VA 23237
Manufacturer Address
CHT
8021 Reycan Road
Richmond, VA 23237
FLAMMABLE LIQUIDS Category 3
WARNING
hazard statements
Causes serious eye irritation
Suspected of damaging fertility or the unborn child
May cause damage to organs through prolonged or repeated exposure
FLAMMABLE LIQUID AND VAPOR
Appearance Liquid Viscous liquid Physical State Liquid
_____________________________________________________________________________________________
PAGE 1 / 9
Odor Slight

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
Obtain special instructions before use
Do not handle until all safety precautions have been read and understood
Use personal protective equipment as required
Wash face, hands and any exposed skin thoroughly after handling
Do not breathe dust/fume/gas/mist/vapors/spray
Keep away from heat/sparks/open flames/hot surfaces. – No smoking
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ ventilating / lighting/ .? / equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower
In case of fire: Use CO2, dry chemical, or foam for extinction
Precautionary Statements – Storage
Store locked up
Store in a well-ventilated place. Keep cool
Precautionary Statements – Disposal
Dispose of contents/container to an approved waste disposal plant
Hazards Not Otherwise Classified (HNOC)
Not Applicable
OTHER INFORMATION
may be harmful if swallowed. May be harmful in contact with skin.
3. Composition/information on Ingredients
Substance
Not Applicable
Mixture
4. First aid measures
Description of first aid measures
General Advice Immediate medical attention is required. In case of accident or unwellness, seek medical
advice immediately (show directions for use or safety data sheet if possible).
Eye Contact Immediately flush with plenty of water. After initial flushing, remove any contact lenses and
continue flushing for at least 15 minutes. Keep eye wide open while rinsing. If symptoms
persist, call a physician.
Skin Contact Wash off immediately with plenty of water.
INHALATION Remove to fresh air. Call a physician. If breathing is irregular or stopped, administer
artificial respiration. Avoid direct contact with skin. Use barrier to give mouth-to-mouth
resuscitation.
INGESTION Do NOT induce vomiting. Rinse mouth. Drink plenty of water. If symptoms persist, call a
physician.
_____________________________________________________________________________________________
PAGE 2 / 9

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
Self-Protection of the First AiderRemove all sources of ignition.
Most Important Symptoms and Effects, Both Acute and Delayed
Symptoms No information available.
Indication of Any Immediate Medical Attention and Special Treatment Needed
Note to physicians Keep victim warm and quiet.
5. Fire-fighting measures
Suitable Extinguishing Media
Dry chemical, CO2, water spray or regular foam. Water spray, fog or regular foam. Use water spray or fog; do not use straight
streams. Move containers from fire area if you can do it without risk.
Unsuitable Extinguishing MediaELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area).
Specific Hazards Arising from the Chemical
Vapors may form explosive mixtures with air. Vapors may travel to source of ignition and flash back. Most vapors are heavier than
air. They will spread along ground and collect in low or confined areas (sewers, basements, tanks). Vapor explosion hazard
indoors, outdoors or in sewers. Those substances designated with a “P” may polymerize explosively when heated or involved in a
fire. Runoff to sewer may create fire or explosion hazard. Substance may be transported hot. FLAMMABLE.
Explosion Data
Sensitivity to Mechanical ImpactNone.
Sensitivity to Static DischargeNone.
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal Precautions Remove all sources of ignition. Evacuate personnel to safe areas. Ensure adequate
ventilation, especially in confined areas. Use personal protective equipment as required.
OTHER INFORMATION Water spray may reduce vapor; but may not prevent ignition in closed spaces.
Environmental Precautions
Environmental Precautions Prevent further leakage or spillage if safe to do so. Prevent product from entering drains. Do
not flush into surface water or sanitary sewer system. See Section 12 for additional
Ecological Information.
Methods and material for containment and cleaning up
Methods for Containment A vapor suppressing foam may be used to reduce vapors. Absorb or cover with dry earth,
sand or other non-combustible material and transfer to containers. Dike far ahead of liquid
spill for later disposal.
Methods for Cleaning Up Pick up and transfer to properly labeled containers. Dam up. Soak up with inert absorbent
material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Soak up with inert
absorbent material.
7. Handling and Storage
Precautions for Safe Handling
Advice on safe handling Ensure adequate ventilation, especially in confined areas. Keep away from heat, sparks,
_____________________________________________________________________________________________
PAGE 3 / 9

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
flame and other sources of ignition (i.e., pilot lights, electric motors and static electricity).
Take precautionary measures against static discharges. Use spark-proof tools and
explosion-proof equipment. All equipment used when handling the product must be
grounded.
Conditions for safe storage, including any incompatibilities
Storage Conditions Keep tightly closed in a dry and cool place. Keep in properly labeled containers. Keep away
from heat, sparks, flame and other sources of ignition (i.e., pilot lights, electric motors and
static electricity).
Incompatible materials None known based on information supplied.
8. Exposure Controls/Personal Protection
Control Parameters
Ingredients with workplace
exposure parameters
.
NIOSH IDLH Immediately Dangerous to Life or Health
OTHER INFORMATION Vacated limits revoked by the Court of Appeals decision in AFL-CIO v. OSHA, 965 F.2d 962
(11th Cir., 1992).
Appropriate Engineering Controls
Engineering controls Showers
Eyewash stations
Individual protection measures, such as personal protective equipment
Eye/Face Protection Tight sealing safety goggles.
Skin and Body Protection Wear protective gloves and protective clothing.
Respiratory Protection No protective equipment is needed under normal use conditions. If exposure limits are
exceeded or irritation is experienced, ventilation and evacuation may be required. Ensure
adequate ventilation, especially in confined areas.
General hygiene considerations When using do not eat, drink or smoke. Regular cleaning of equipment, work area and
clothing is recommended.
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Physical State Liquid
Appearance Liquid Viscous liquid Odor Slight
Color Green Odor threshold No information available
Property VALUES Remarks Method
pH No information available
Melting point / Freezing point No information available
Boiling point / Boiling range > 65 C / 149 F
Flash point > 39 C / > 102 F CC (closed cup)
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability limit in air
Upper flammability limit: No information available
Lower flammability limit: No information available
Vapor pressure No information available
Vapor density No information available
_____________________________________________________________________________________________
PAGE 4 / 9

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
Explosive properties Not an explosive
Oxidizing properties This product is not an oxidizing agent
OTHER INFORMATION
Softening point No information available
Molecular weight No information available
VOC content (%) No information available
Density 1.00
Bulk density No information available
10. Stability and Reactivity
Reactivity
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
None under normal processing.
Conditions to avoid
Heat, flames and sparks.
Incompatible materials
None known based on information supplied.
Hazardous decomposition products
None known based on information supplied.
11. Toxicological Information
Information on Likely Routes of Exposure
Product information No data available.
INHALATION No data available.
Eye Contact No data available.
Skin Contact No data available.
INGESTION No data available.
Information on Toxicological Effects
Symptoms No information available.
Delayed and immediate effects as well as chronic effects from short and long-term exposure
Relative density No information available
Water solubility No information available
Solubility in other solvents No information available
Partition coefficient No information available
Autoignition temperature No information available
Decomposition temperature No information available
Kinematic viscosity No information available
Dynamic viscosity 100 cps
_____________________________________________________________________________________________
PAGE 5 / 9
No data available

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
sensitization No information available.
Germ Cell Mutagenicity No information available.
carcinogenicity The table below indicates whether each agency has listed any ingredient as a carcinogen.
This product contains one or more substances which are classified by IARC as
carcinogenic to humans (Group I), probably carcinogenic to humans (Group 2A) or possibly
carcinogenic to humans (Group 2B).
IARC (International Agency for Research on Cancer)
Not classifiable as a human carcinogen
Reproductive Toxicity No information available.
STOT – Single Exposure No information available.
STOT – Repeated Exposure No information available.
Chronic Toxicity May cause adverse effects on the bone marrow and blood-forming system. May cause
adverse liver effects.
Target organ effects Blood, Central Nervous System, EYES, Kidney, Liver, Respiratory System, skin, Urinary
tract.
Aspiration Hazard No information available.
Numerical Measures of Toxicity – Product information
The following values are calculated based on chapter 3.1 of the GHS document
ATEmix (oral) 3,011.00 mg/kg
ATEmix (dermal) 2,562.00 mg/kg
ATEmix (inhalation-vapor) 69.73 mg/l
12. Ecological Information
Ecotoxicity
Harmful to aquatic life
Chemical name Algae/aquatic plants Fish Crustacea
COPPER
POLYCHLOROPHTHALOCYANIN
E GREEN
1328-53-6
– 752.4: 96 h Lepomis macrochirus
mg/L LC50 static
500: 24 h Daphnia magna Straus
mg/L EC50
Methanol
67-56-1
– 19500 – 20700: 96 h Oncorhynchus
mykiss mg/L LC50 flow-through
28200: 96 h Pimephales promelas
mg/L LC50 flow-through 18 – 20: 96
h Oncorhynchus mykiss mL/L LC50
static 100: 96 h Pimephales
promelas mg/L LC50 static 13500 –
17600: 96 h Lepomis macrochirus
mg/L LC50 flow-through

Persistence and Degradability
No information available.
Bioaccumulation
No information available.
Other Adverse Effects No information available
Ozone depletion potential (ODP)No information available
13. Disposal Considerations
Waste Treatment Methods
Disposal of wastes This material, as supplied, is a hazardous waste according to federal regulations (40 CFR
261).
Contaminated Packaging Do not reuse container.
_____________________________________________________________________________________________
PAGE 6 / 9

_____________________________________________________________________________________________
Flex Cat 25 Revision date 29-Mar-2018
US EPA Waste Number U154 D001
Chemical name RCRA RCRA – Basis for ListingRCRA – D Series Wastes RCRA – U Series Wastes
Methanol
67-56-1
– Included in waste stream:
F039
– U154
This product contains one or more substances that are listed with the State of California as a hazardous waste.
14. Transport Information
DOT Regulated
UN/ID no UN1993
Proper Shipping Name Flammable liquids, n.o.s.
Hazard class 3
Packing group III
Special Provisions B1, B52, IB3, T4, TP1, TP29
Description UN1993, Flammable liquids, n.o.s.(Methanol), 3, III
Emergency Response Guide
Number
128
IATA Regulated
UN/ID no UN1993
Hazard class 3
Packing group III
ERG Code 3L
Special Provisions A3
Description UN1993, Flammable liquid, n.o.s. (Methanol), 3, III
IMDG Regulated
UN/ID no UN1993
Proper Shipping Name Flammable liquid, n.o.s.
Hazard class 3
Packing group III
EmS-No F-E, S-E
Special Provisions 223, 274, 955
Special Precautions This material is not DOT regulated in containers < 119 gallons 15. Regulatory Information International Inventories TSCA Complies DSL/NDSL Complies EINECS/ELINCS Complies ENCS Complies IECSC Complies KECL Complies PICCS Complies AICS Complies TCSI Complies Legend: TSCA - United States Toxic Substances Control Act Section 8(b) Inventory DSL/NDSL - Canadian Domestic Substances List/Non-Domestic Substances List EINECS/ELINCS - European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances _____________________________________________________________________________________________ PAGE 7 / 9 ENCS - Japan Existing and New Chemical Substances _____________________________________________________________________________________________ Flex Cat 25 Revision date 29-Mar-2018 IECSC - China Inventory of Existing Chemical Substances KECL - Korean Existing and Evaluated Chemical Substances PICCS - Philippines Inventory of Chemicals and Chemical Substances AICS - Australian Inventory of Chemical Substances TCSI - Taiwan Chemical Substance Inventory US Federal Regulations SARA 313 Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product does not contain any chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372 Chemical name SARA 313 - Threshold Values % COPPER POLYCHLOROPHTHALOCYANINE GREEN - 1328-53-6 1.0 Methanol - 67-56-1 1.0 SARA 311/312 Hazard Categories Acute Health Hazard YES Chronic health hazard NO Fire Hazard YES Sudden Release of Pressure Hazard NO Reactive Hazard NO CWA (Clean Water Act) This product does not contain any substances regulated as pollutants pursuant to the Clean Water Act (40 CFR 122.21 and 40 CFR 122.42) CERCLA This material, as supplied, contains one or more substances regulated as a hazardous substance under the Comprehensive Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302) US State Regulations California Proposition 65 This product contains Proposition 65 chemicals Chemical name California Proposition 65 Methanol - 67-56-1 Developmental U.S. State Right-to-Know Regulations Chemical name New Jersey Massachusetts Pennsylvania COPPER POLYCHLOROPHTHALOCYANIN E GREEN 1328-53-6 X - X Methanol 67-56-1 X X X U.S. EPA Label information EPA Pesticide registration numberNot Applicable 16. Other information, including date of preparation of the last revision Issue date 05-Mar-2018 Revision date 29-Mar-2018 Revision note No information available Disclaimer The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage, NFPA Health Hazards 2 Flammability 2 Instability 1 - HMIS Health Hazards 2 Flammability 2 Physical Hazards 1 _____________________________________________________________________________________________ PAGE 8 / 9 - _____________________________________________________________________________________________ Flex Cat 25 Revision date 29-Mar-2018 transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. End of Safety Data Sheet _____________________________________________________________________________________________ PAGE 9 / 9

17FLEX25AF_SDS.pdf

Safety Data Sheet
Issue date 28-Feb-2018 Revision date 28-Sep-2018 Version 2
1. Identification
Product Identifier
Product name Flex 25
Other means of identification
Recommended use of the chemical and restrictions on use
Recommended use Industrial silicone elastomer.
Application FOR INDUSTRIAL USE ONLY
Details of the Supplier of the Safety Data Sheet
Emergency Telephone Number
Company Phone Number 800-852-3147 (8AM – 5PM EST)
Emergency telephone Chemtrec 1-800-424-9300
2. Hazards Identification
Classification
OSHA Regulatory Status
This chemical is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Label Elements
EMERGENCY OVERVIEW
Hazards Not Otherwise Classified (HNOC)
Not Applicable
OTHER INFORMATION
Not Applicable.
3. Composition/information on Ingredients
Substance
Not Applicable
Mixture
Chemical name CAS No weight-% Trade secret
Supplier
CHT
7820 Whitepine Rd
Richmond, VA 23237
Manufacturer Address
CHT
8021 Reycan Road
Richmond, VA 23237
The product contains no substances which at their given concentration, are considered to be hazardous to health
Appearance Viscous liquid Physical State Liquid
_____________________________________________________________________________________________
PAGE 1 / 7
Odor Negligible

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Silica, quartz 14808-60-7 3 – 7 *
Titanium Dioxide 13463-67-7 0.1 – 1 *
4. First aid measures
Description of first aid measures
Eye Contact Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids.
Consult a physician.
Skin Contact Wash skin with soap and water.
INHALATION Remove to fresh air.
INGESTION Clean mouth with water and drink afterwards plenty of water.
Most Important Symptoms and Effects, Both Acute and Delayed
Symptoms No information available.
Indication of Any Immediate Medical Attention and Special Treatment Needed
Note to physicians Treat symptomatically.
5. Fire-fighting measures
Suitable Extinguishing Media
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable Extinguishing MediaCAUTION: Use of water spray when fighting fire may be inefficient.
Specific Hazards Arising from the Chemical
No information available.
Explosion Data
Sensitivity to Mechanical ImpactNone.
Sensitivity to Static DischargeNone.
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal Precautions Ensure adequate ventilation, especially in confined areas.
Environmental Precautions
Environmental Precautions See Section 12 for additional Ecological Information.
Methods and material for containment and cleaning up
Methods for Containment Prevent further leakage or spillage if safe to do so.
Methods for Cleaning Up Use personal protective equipment as required. Dam up. Cover liquid spill with sand, earth
or other non-combustible absorbent material. Take up mechanically, placing in appropriate
containers for disposal. Clean contaminated surface thoroughly.
7. Handling and Storage
_____________________________________________________________________________________________
PAGE 2 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Precautions for Safe Handling
Advice on safe handling Handle in accordance with good industrial hygiene and safety practice.
Conditions for safe storage, including any incompatibilities
Storage Conditions Keep containers tightly closed in a dry, cool and well-ventilated place.
Incompatible materials Incompatible with strong acids and bases. Interaction with strong bases can cause
liberation of hydrogen.
8. Exposure Controls/Personal Protection
Control Parameters
Ingredients with workplace
exposure parameters
.
Chemical name ACGIH TLV OSHA PEL NIOSH IDLH
Titanium Dioxide
13463-67-7
TWA: 10 mg/m
3
TWA: 15 mg/m
3
total dust
(vacated) TWA: 10 mg/m
3
total dust
IDLH: 5000 mg/m
3
NIOSH IDLH Immediately Dangerous to Life or Health
OTHER INFORMATION Vacated limits revoked by the Court of Appeals decision in AFL-CIO v. OSHA, 965 F.2d 962
(11th Cir., 1992).
Appropriate Engineering Controls
Engineering controls Showers
Eyewash stations
Individual protection measures, such as personal protective equipment
Eye/Face Protection Wear safety glasses with side shields (or goggles).
Skin and Body Protection Wear protective gloves and protective clothing.
Respiratory Protection No protective equipment is needed under normal use conditions.
General hygiene considerations Handle in accordance with good industrial hygiene and safety practice.
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Physical State Liquid
Appearance Viscous liquid Odor Negligible
Color Beige Odor threshold No information available
Property VALUES Remarks Method
pH No information available
Melting point / Freezing point No information available
Boiling point / Boiling range No information available
Flash point > 140 C / > 284 F CC (closed cup)
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability limit in air
Upper flammability limit: No information available
Lower flammability limit: No information available
Vapor pressure No information available
Vapor density No information available
Relative density No information available
Water solubility No information available
_____________________________________________________________________________________________
PAGE 3 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Explosive properties Not an explosive
Oxidizing properties This product is not an oxidizing agent
OTHER INFORMATION
Softening point No information available
Molecular weight No information available
VOC content (%) No information available
Density 1.16
Bulk density No information available
10. Stability and Reactivity
Reactivity
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
None under normal processing.
hazardous polymerization No information available.
Conditions to avoid
No information available.
Incompatible materials
Incompatible with strong acids and bases. Interaction with strong bases can cause liberation of hydrogen.
Hazardous decomposition products
None known based on information supplied.
11. Toxicological Information
Information on Likely Routes of Exposure
Product information No data available.
INHALATION No data available.
Eye Contact No data available.
Skin Contact No data available.
INGESTION No data available.
Chemical name Oral LD50 dermal LD50 Inhalation LC50
Titanium Dioxide
13463-67-7
> 10000 mg/kg ( Rat ) – –
Information on Toxicological Effects
Symptoms No information available.
Solubility in other solvents No information available
Partition coefficient No information available
Autoignition temperature No information available
Decomposition temperature No information available
Kinematic viscosity No information available
Dynamic viscosity 35,000 cps
No data available
_____________________________________________________________________________________________
PAGE 4 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Delayed and immediate effects as well as chronic effects from short and long-term exposure
sensitization No information available.
Germ Cell Mutagenicity No information available.
carcinogenicity The table below indicates whether each agency has listed any ingredient as a carcinogen.
This product contains one or more substances which are classified by IARC as
carcinogenic to humans (Group I), probably carcinogenic to humans (Group 2A) or possibly
carcinogenic to humans (Group 2B).
Chemical name ACGIH IARC NTP OSHA
Silica, quartz
14808-60-7
A2 Group 1 Known X
Titanium Dioxide
13463-67-7
– Group 2B – X
ACGIH (American Conference of Governmental Industrial Hygienists)
A2 – Suspected Human Carcinogen
IARC (International Agency for Research on Cancer)
Group 1 – Carcinogenic to Humans
Group 2B – Possibly Carcinogenic to Humans
Not classifiable as a human carcinogen
NTP (National Toxicology Program)
Known – Known Carcinogen
OSHA (Occupational Safety and Health Administration of the US Department of Labor)
X – Present
Reproductive Toxicity No information available.
STOT – Single Exposure No information available.
STOT – Repeated Exposure No information available.
Target organ effects EYES, Lungs, Respiratory System.
Aspiration Hazard No information available.
Numerical Measures of Toxicity – Product information
The following values are calculated based on chapter 3.1 of the GHS document
ATEmix (oral) 11,687.00 mg/kg
ATEmix (dermal) 5,664.00 mg/kg
12. Ecological Information
Ecotoxicity
Chemical name Algae/aquatic plants Fish Crustacea
Octamethylcyclotetrasiloxane
556-67-2
– 500: 96 h Brachydanio rerio mg/L
LC50 1000: 96 h Lepomis
macrochirus mg/L LC50
25.2: 24 h Daphnia magna mg/L
EC50
Persistence and Degradability
No information available.
Bioaccumulation
No information available.
Other Adverse Effects No information available
13. Disposal Considerations
Waste Treatment Methods
Disposal of wastes Disposal should be in accordance with applicable regional, national and local laws and
regulations.
Contaminated Packaging Do not reuse container.
_____________________________________________________________________________________________
PAGE 5 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
14. Transport Information
DOT NOT REGULATED
IATA NOT REGULATED
IMDG NOT REGULATED
15. Regulatory Information
International Inventories
TSCA Complies
DSL/NDSL Complies
EINECS/ELINCS Complies
ENCS Complies
IECSC Complies
KECL Complies
PICCS Complies
AICS Complies
TCSI Complies
Legend:
TSCA – United States Toxic Substances Control Act Section 8(b) Inventory
DSL/NDSL – Canadian Domestic Substances List/Non-Domestic Substances List
EINECS/ELINCS – European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
ENCS – Japan Existing and New Chemical Substances
IECSC – China Inventory of Existing Chemical Substances
KECL – Korean Existing and Evaluated Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
AICS – Australian Inventory of Chemical Substances
TCSI – Taiwan Chemical Substance Inventory
US Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product does not contain any
chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
SARA 311/312 Hazard Categories
Acute Health Hazard NO
Chronic health hazard NO
Fire Hazard NO
Sudden Release of Pressure Hazard NO
Reactive Hazard NO
CWA (Clean Water Act)
This product does not contain any substances regulated as pollutants pursuant to the Clean Water Act (40 CFR 122.21 and 40
CFR 122.42)
CERCLA
This material, as supplied, does not contain any substances regulated as hazardous substances under the Comprehensive
Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302) or the Superfund Amendments and
Reauthorization Act (SARA) (40 CFR 355). There may be specific reporting requirements at the local, regional, or state level
pertaining to releases of this material
_____________________________________________________________________________________________
PAGE 6 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
US State Regulations
California Proposition 65
This product does not contain any Proposition 65 chemicals
Chemical name California Proposition 65
Silica, quartz – 14808-60-7 Carcinogen
Titanium Dioxide – 13463-67-7 Carcinogen
U.S. State Right-to-Know Regulations
U.S. EPA Label information
EPA Pesticide registration numberNot Applicable
16. Other information, including date of preparation of the last revision
Issue date 28-Feb-2018
Revision date 28-Sep-2018
Revision note
No information available
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
End of Safety Data Sheet
NFPA Health Hazards 0 Flammability 1 Instability 0 –
HMIS Health Hazards 0 Flammability 1 Physical Hazards 0 –
_____________________________________________________________________________________________
PAGE 7 / 7

17FLEX25AD_SDS.pdf

Safety Data Sheet
Issue date 28-Feb-2018 Revision date 28-Sep-2018 Version 2
1. Identification
Product Identifier
Product name Flex 25
Other means of identification
Recommended use of the chemical and restrictions on use
Recommended use Industrial silicone elastomer.
Application FOR INDUSTRIAL USE ONLY
Details of the Supplier of the Safety Data Sheet
Emergency Telephone Number
Company Phone Number 800-852-3147 (8AM – 5PM EST)
Emergency telephone Chemtrec 1-800-424-9300
2. Hazards Identification
Classification
OSHA Regulatory Status
This chemical is not considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Label Elements
EMERGENCY OVERVIEW
Hazards Not Otherwise Classified (HNOC)
Not Applicable
OTHER INFORMATION
Not Applicable.
3. Composition/information on Ingredients
Substance
Not Applicable
Mixture
Chemical name CAS No weight-% Trade secret
Supplier
CHT
7820 Whitepine Rd
Richmond, VA 23237
Manufacturer Address
CHT
8021 Reycan Road
Richmond, VA 23237
The product contains no substances which at their given concentration, are considered to be hazardous to health
Appearance Viscous liquid Physical State Liquid
_____________________________________________________________________________________________
PAGE 1 / 7
Odor Negligible

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Silica, quartz 14808-60-7 3 – 7 *
Titanium Dioxide 13463-67-7 0.1 – 1 *
4. First aid measures
Description of first aid measures
Eye Contact Rinse thoroughly with plenty of water for at least 15 minutes, lifting lower and upper eyelids.
Consult a physician.
Skin Contact Wash skin with soap and water.
INHALATION Remove to fresh air.
INGESTION Clean mouth with water and drink afterwards plenty of water.
Most Important Symptoms and Effects, Both Acute and Delayed
Symptoms No information available.
Indication of Any Immediate Medical Attention and Special Treatment Needed
Note to physicians Treat symptomatically.
5. Fire-fighting measures
Suitable Extinguishing Media
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable Extinguishing MediaCAUTION: Use of water spray when fighting fire may be inefficient.
Specific Hazards Arising from the Chemical
No information available.
Explosion Data
Sensitivity to Mechanical ImpactNone.
Sensitivity to Static DischargeNone.
Protective Equipment and Precautions for Firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. Accidental release measures
Personal precautions, protective equipment and emergency procedures
Personal Precautions Ensure adequate ventilation, especially in confined areas.
Environmental Precautions
Environmental Precautions See Section 12 for additional Ecological Information.
Methods and material for containment and cleaning up
Methods for Containment Prevent further leakage or spillage if safe to do so.
Methods for Cleaning Up Use personal protective equipment as required. Dam up. Cover liquid spill with sand, earth
or other non-combustible absorbent material. Take up mechanically, placing in appropriate
containers for disposal. Clean contaminated surface thoroughly.
7. Handling and Storage
_____________________________________________________________________________________________
PAGE 2 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Precautions for Safe Handling
Advice on safe handling Handle in accordance with good industrial hygiene and safety practice.
Conditions for safe storage, including any incompatibilities
Storage Conditions Keep containers tightly closed in a dry, cool and well-ventilated place.
Incompatible materials Incompatible with strong acids and bases. Interaction with strong bases can cause
liberation of hydrogen.
8. Exposure Controls/Personal Protection
Control Parameters
Ingredients with workplace
exposure parameters
.
Chemical name ACGIH TLV OSHA PEL NIOSH IDLH
Titanium Dioxide
13463-67-7
TWA: 10 mg/m
3
TWA: 15 mg/m
3
total dust
(vacated) TWA: 10 mg/m
3
total dust
IDLH: 5000 mg/m
3
NIOSH IDLH Immediately Dangerous to Life or Health
OTHER INFORMATION Vacated limits revoked by the Court of Appeals decision in AFL-CIO v. OSHA, 965 F.2d 962
(11th Cir., 1992).
Appropriate Engineering Controls
Engineering controls Showers
Eyewash stations
Individual protection measures, such as personal protective equipment
Eye/Face Protection Wear safety glasses with side shields (or goggles).
Skin and Body Protection Wear protective gloves and protective clothing.
Respiratory Protection No protective equipment is needed under normal use conditions.
General hygiene considerations Handle in accordance with good industrial hygiene and safety practice.
9. Physical and Chemical Properties
Information on basic physical and chemical properties
Physical State Liquid
Appearance Viscous liquid Odor Negligible
Color Beige Odor threshold No information available
Property VALUES Remarks Method
pH No information available
Melting point / Freezing point No information available
Boiling point / Boiling range No information available
Flash point > 140 C / > 284 F CC (closed cup)
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability limit in air
Upper flammability limit: No information available
Lower flammability limit: No information available
Vapor pressure No information available
Vapor density No information available
Relative density No information available
Water solubility No information available
_____________________________________________________________________________________________
PAGE 3 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Explosive properties Not an explosive
Oxidizing properties This product is not an oxidizing agent
OTHER INFORMATION
Softening point No information available
Molecular weight No information available
VOC content (%) No information available
Density 1.16
Bulk density No information available
10. Stability and Reactivity
Reactivity
Chemical stability
Stable under recommended storage conditions.
Possibility of hazardous reactions
None under normal processing.
hazardous polymerization No information available.
Conditions to avoid
No information available.
Incompatible materials
Incompatible with strong acids and bases. Interaction with strong bases can cause liberation of hydrogen.
Hazardous decomposition products
None known based on information supplied.
11. Toxicological Information
Information on Likely Routes of Exposure
Product information No data available.
INHALATION No data available.
Eye Contact No data available.
Skin Contact No data available.
INGESTION No data available.
Chemical name Oral LD50 dermal LD50 Inhalation LC50
Titanium Dioxide
13463-67-7
> 10000 mg/kg ( Rat ) – –
Information on Toxicological Effects
Symptoms No information available.
Solubility in other solvents No information available
Partition coefficient No information available
Autoignition temperature No information available
Decomposition temperature No information available
Kinematic viscosity No information available
Dynamic viscosity 35,000 cps
No data available
_____________________________________________________________________________________________
PAGE 4 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
Delayed and immediate effects as well as chronic effects from short and long-term exposure
sensitization No information available.
Germ Cell Mutagenicity No information available.
carcinogenicity The table below indicates whether each agency has listed any ingredient as a carcinogen.
This product contains one or more substances which are classified by IARC as
carcinogenic to humans (Group I), probably carcinogenic to humans (Group 2A) or possibly
carcinogenic to humans (Group 2B).
Chemical name ACGIH IARC NTP OSHA
Silica, quartz
14808-60-7
A2 Group 1 Known X
Titanium Dioxide
13463-67-7
– Group 2B – X
ACGIH (American Conference of Governmental Industrial Hygienists)
A2 – Suspected Human Carcinogen
IARC (International Agency for Research on Cancer)
Group 1 – Carcinogenic to Humans
Group 2B – Possibly Carcinogenic to Humans
Not classifiable as a human carcinogen
NTP (National Toxicology Program)
Known – Known Carcinogen
OSHA (Occupational Safety and Health Administration of the US Department of Labor)
X – Present
Reproductive Toxicity No information available.
STOT – Single Exposure No information available.
STOT – Repeated Exposure No information available.
Target organ effects EYES, Lungs, Respiratory System.
Aspiration Hazard No information available.
Numerical Measures of Toxicity – Product information
The following values are calculated based on chapter 3.1 of the GHS document
ATEmix (oral) 11,687.00 mg/kg
ATEmix (dermal) 5,664.00 mg/kg
12. Ecological Information
Ecotoxicity
Chemical name Algae/aquatic plants Fish Crustacea
Octamethylcyclotetrasiloxane
556-67-2
– 500: 96 h Brachydanio rerio mg/L
LC50 1000: 96 h Lepomis
macrochirus mg/L LC50
25.2: 24 h Daphnia magna mg/L
EC50
Persistence and Degradability
No information available.
Bioaccumulation
No information available.
Other Adverse Effects No information available
13. Disposal Considerations
Waste Treatment Methods
Disposal of wastes Disposal should be in accordance with applicable regional, national and local laws and
regulations.
Contaminated Packaging Do not reuse container.
_____________________________________________________________________________________________
PAGE 5 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
14. Transport Information
DOT NOT REGULATED
IATA NOT REGULATED
IMDG NOT REGULATED
15. Regulatory Information
International Inventories
TSCA Complies
DSL/NDSL Complies
EINECS/ELINCS Complies
ENCS Complies
IECSC Complies
KECL Complies
PICCS Complies
AICS Complies
TCSI Complies
Legend:
TSCA – United States Toxic Substances Control Act Section 8(b) Inventory
DSL/NDSL – Canadian Domestic Substances List/Non-Domestic Substances List
EINECS/ELINCS – European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
ENCS – Japan Existing and New Chemical Substances
IECSC – China Inventory of Existing Chemical Substances
KECL – Korean Existing and Evaluated Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
AICS – Australian Inventory of Chemical Substances
TCSI – Taiwan Chemical Substance Inventory
US Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product does not contain any
chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
SARA 311/312 Hazard Categories
Acute Health Hazard NO
Chronic health hazard NO
Fire Hazard NO
Sudden Release of Pressure Hazard NO
Reactive Hazard NO
CWA (Clean Water Act)
This product does not contain any substances regulated as pollutants pursuant to the Clean Water Act (40 CFR 122.21 and 40
CFR 122.42)
CERCLA
This material, as supplied, does not contain any substances regulated as hazardous substances under the Comprehensive
Environmental Response Compensation and Liability Act (CERCLA) (40 CFR 302) or the Superfund Amendments and
Reauthorization Act (SARA) (40 CFR 355). There may be specific reporting requirements at the local, regional, or state level
pertaining to releases of this material
_____________________________________________________________________________________________
PAGE 6 / 7

_____________________________________________________________________________________________
Flex 25 Revision date 28-Sep-2018
US State Regulations
California Proposition 65
This product does not contain any Proposition 65 chemicals
Chemical name California Proposition 65
Silica, quartz – 14808-60-7 Carcinogen
Titanium Dioxide – 13463-67-7 Carcinogen
U.S. State Right-to-Know Regulations
U.S. EPA Label information
EPA Pesticide registration numberNot Applicable
16. Other information, including date of preparation of the last revision
Issue date 28-Feb-2018
Revision date 28-Sep-2018
Revision note
No information available
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
End of Safety Data Sheet
NFPA Health Hazards 0 Flammability 1 Instability 0 –
HMIS Health Hazards 0 Flammability 1 Physical Hazards 0 –
_____________________________________________________________________________________________
PAGE 7 / 7

17E497_SDS.pdf

Safety Data Sheet
E497 Thermoset Mold Release
Copying and/or downloading of this information for the purpose of properly utilizing Stoner Inc. product is allowed provided that: (1) the
information is copied in full with no changes unless prior agreement is obtained from Stoner Inc., & (2) neither the copy nor the original is
resold or otherwise distributed with intention of earning profit thereon.
fl. IDENTIFICATION
[Stoner Incorporated Product Name: Thermoset Mold Release
1070 Robert Fulton Hwy. Product Code: E497
Quarryville, PA 17566 Product Use: Mold Release
1-800-227-5538 24-hour emergency phone: 1-800-424-9300 [CHEMTREC]
b. HAZARD IDENTIFICATION
POTENTIAL HEALTH EFFECTS
Classification of the chemical in accordance with paragraph (d) of 1910.1200;
GHS Hazard Symbols ‘
GHS Classification Flammable Aerosol Category 1
Gases under pressure – Liquified Gas
Skin Corrosion/Irritation Category 2
Specific Target Organ Systemic Toxicity (STOT) – Single Exposure Category 3
Signal Word Danger
Hazard Statements Extremely flammable aerosol.
Contains gas under pressure; may explode if heated.
Causes skin irritation.
May cause drowsiness or dizziness.
Precautionary Statements
Prevention Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
Do not spray on an open flame or other ignition source.
Pressurized container: Do not pierce or burn, even after use.
Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 – Wash thoroughly after handling.
Use only outdoors or in a well-ventilated area.
Wear protective gloves/protective clothing/eye protection/face protection.
Response P302+P352 – If on skin: Wash with plenty of soap and water.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312 – Call a poison center, doctor or medical center if you feel unwell.
P321 – Specific treatment (see on this SDS).
If skin irritation occurs: Get medical advice/attention.
Storage Store in a well-ventilated place. Keep container tightly closed.
Store locked up.
Protect from sunlight. Store in a well-ventilated place.
Protect from sunlight. Do no expose to temperatures exceeding 50 C/ 12 F.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulation for hazardous
Bb. COMPOSITION/INFORMATION ON INGREDIENTS
COMPONENT CAS # Percent
Petroleum distillates 64741-65-7 60-80
Ether propellant 115-10-6 1-20
Hydrocarbon propellant 68476-86-8 1-20
Stoner Incorporated E497 PAGE 1

17E302_SDS.pdf

Safety Data Sheet
E302 Rocket Release
Copying and/or downloading of this information for the purpose of properly utilizing Stoner Inc. product is allowed provided that: (1) the
information is copied in full with no changes unless prior agreement is obtained from Stoner Inc., & (2) neither the copy nor the original is
resold or otherwise distributed with intention of earning profit thereon.
fl. IDENTIFICATION
[Stoner Incorporated Product Name: Rocket Releasew
1070 Robert Fulton Hwy. Product Code: E302
Quarryville, PA 17566 Product Use: Mold Release
1-800-227-5538 24-hour emergency phone: 1-800-424-9300 [CHEMTREC]
b. HAZARD IDENTIFICATION
POTENTIAL HEALTH EFFECTS,
Classification of the chemical in accordance with paragraph (d) of 1910.1200;
GHS Hazard Symbols ‘ ‘
GHS Classification Gases under pressure – Liquified Gas
Aspiration Hazard Category 1
Flammable Aerosol Category 2
Skin Corrosion/Irritation Category 2
Specific Target Organ Systemic Toxicity (STOT) – Single Exposure Category 3
Signal Word Danger
Hazard Statements Flammable aerosol.
Contains gas under pressure; may explode if heated.
May be fatal if swallowed and enters airways.
Causes skin irritation.
May cause drowsiness or dizziness.
Precautionary Statements
Prevention Keep away from heat/sparks/open flames/hot surfaces. – No smoking.
Do not spray on an open flame or other ignition source.
Pressurized container: Do not pierce or burn, even after use.
Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 – Wash thoroughly after handling.
Use only outdoors or in a well-ventilated area.
Wear protective gloves/protective clothing/eye protection/face protection.
Response P301+P310 – If swallowed: Immediately call a poison center, doctor or medical center.
P302+P352 – If on skin: Wash with plenty of soap and water.
IF INHALED: Remove victim to fresh air and keep at rest in a position comfortable for breathing.
P312 – Call a poison center, doctor or medical center if you feel unwell.
P321 – Specific treatment (see on this SDS).
Do NOT induce vomiting.
If skin irritation occurs: Get medical advice/attention.
Storage Store in a well-ventilated place. Keep container tightly closed.
Store locked up.
Protect from sunlight. Store in a well-ventilated place.
Protect from sunlight. Do no expose to temperatures exceeding 50 C/ 12 F.
Disposal Dispose of contents/container in accordance with local/regional/national/international regulation for hazardous
Stoner Incorporated E302 PAGE 1

17E236A_SDS.pdf

Introducing E236 Urethane Mold Release
Prevents Mold Sticking. For lore Parts in Less Tne Spend Less Time Cleaning.
Saves You Time. [ Urethane Mold Release is so effective,
E236 Urethane Mold Release will let : it actually works better when you use
your molded parts release easily, and less. You’ll no longer have to spray and
reduce rejects. You’ll mold more spray and spray your molds. Your parts
parts, in less time, without 5 : will release easily, but you won’t waste
compromising part quality. Be ee Conte your time cleaning excessive residue from
9 a Ure th ae your molds or your parts,
You’ll Get Fewer Defects, Se) ee Ach For More Information, Call

ieee Seep Motel Release
The wrong mold spray can produce Ps Peventalivticns, Galiz tad A
surface defects caused by residual 5% a ee Ligh Fale Go

ir i py sevides Fast, Easy Part Renee
solvents or incompatible release AS Moldsanid ftulfiple Park BOF 2
agents. Urethane Mold Release is Bot: per Applicatidti>,. 7-4 .
made specifically for molded Waa renee, B)Benterprises
urethane. Its unique non-stick Una tats RO EAR: :
formulation improves flow in the PRES ay ig were dl 14791 Franklin Avenue
mold and provides a smooth, high- able a See aoe aha Tustin, CA 92780
quality par finish SO oe Soy Glad Phone 714-734-8450

: GAIT cis wanes Fax 714-734-8929
eae eal stem info@bjbenterprises.com
NET Weighr 307 HT GRRD ZG : :

236 Urethane Mold Release Technical Data
Active Ingredients nnn nnunnenee Proptielary urethane mold release 236 contains no chlorofluorocatbon (CFC) solvents or propellants, no Class I ozone
Flammability Rating unsssnsnnmnnnnnnesnnene NOnflamimable 2er050l depleting) conroled substances, and no chlorated solvens such as methylene chlo-
Paintabilly wn. Parl cleaning Is recommended prot to painting or decorating tide. Before using, for detailed safety & handling information, akvays refer to the Ma-
PACKAGING an snennsnsnnanngninnsnreninnne TENG B670SOI CANS pet CASE letial Safety Data Sheet availabe for this product from your employer.

17E236-A_SDS.pdf

we
Introducing E236 Urethane Mold Release
Prevents Mold Sticking. For More Parts in Less Tie < Spend Less Time Cleaning. Saves You Time. : Urethane Mold Release is so effective, E236 Urethane Mold Release will Jet itactually works better when you use your molded parts release easily, and fess. You'll no longer have to spray and reduce rejects. You'll mold more spray and spray your molds. Your parts parts, in less time, without 4 : will release easily, but you won't waste compromising part quality. ihe Seen your time cleaning excessive residue from See ey your molds or your parts, 2 ee L Ape 33 You'll Get Fewer Defects, Mintel Ralaace For More Information, Call Less Scrap. ke Mold-Releas 4 The wrong mold spray can produce % PeentsUialiane Ba grok SN surface defects caused by residual NS Siowdide tS eas, pad neo Mice i . ps ovides Fast, ERisy Part Renos = solvents or incompatible release F.* SMoldscand ffulfiple Part Bees 3 agents, Urethane Mold Release is Feet per ApplicaliOhs? 74 . made specifically for molded Gree renee BjBenterprises urethane. Its unique non-stick Se Sea eee : formulation improves flow in the SES a eae eee ioe 14791 Franklin Avenue mold and provides a smooth, high- fly Dts eee BERET Tustin, CA 92780 quality part finish. SEES poe Se Gd Phone 714-734-8450

17DMF50-D_SDS.pdf

Able Industrial Products, Inc.
SAFETY DATA SHEET
1. PRODUCT IDENTIFICATION
TRADE NAME: AMTDMF50 Fluid GTDMF-5cS+
OTHER MEANS OF . – .
IDENTIFICATION: Identical SDS for all DMF fluids at and above a viscosity of 5cS
RECOMMENDED USE OF .
PRODUCT: Mold-making Rubber
SUPPLIER S DETAILS: Able Industrial Products, inc.
2006 S. Baker Ave
Ontario, Ca. 91761
Telephone: (909)930-1585
Fax: (909) 930-9382
EMERGENCY CONTACT: CHEMTREC (24 Hours):1-800-424-9300
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATION
PHYSICAL HAZARDS Not Classified
HEALTH HAZARDS Not Classified
ENVIRONMENTAL HAZARDS Not Classified
GHS LABEL ELEMENTS
PICTOGRAMS None
SIGNAL WORDS None
HAZARD STATEMENTS None
PRECAUTIONARY STATEMENTS
[PREVENTION] None
[RESPONSE] None
[STORAGE] None
[DISPOSAL] None
AMTDMEF5O Fluid printed: 07/11/24 page 1 of 6

17D3302679_SDS.pdf

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

1 / 11
SECTION 1. IDENTIFICATION
Product name

: DOWSIL TB/TL/CER Sealant Clear

Product code

: 04045036

Manufacturer or supplier’s details
Company Identification

: THE DOW CHEMICAL COMPANY
2030 WILLARD H DOW CENTER
MIDLAND MI 48674-0000
UNITED STATES

Telephone

: 800-258-2436

24-Hour Emergency Contact

: Chemtrec +1 800-424-9300

Local Emergency Number

: 800-424-9300

E-mail address : SDSQuestion@dow.com
Recommended use of the chemical and restrictions on use
Recommended use

: Adhesive, binding agents

SECTION 2. HAZARDS IDENTIFICATION
GHS classification in accordance with 29 CFR 1910.1200
Not a hazardous substance or mixture.
GHS label elements
Not a hazardous substance or mixture.
Precautionary Statements

:
Prevention:
P271 Use only outdoors or in a well-ventilated area.

Other hazards
None known.
SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS
Substance / Mixture

: Mixture
Chemical nature

: Silicone elastomer

Hazardous ingredients
Chemical name CAS-No. Concentration (% w/w)
Silicon dioxide 7631-86-9 >= 8 – <= 9 SECTION 4. FIRST AID MEASURES SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 2 / 11 If inhaled : If inhaled, remove to fresh air. Get medical attention if symptoms occur. In case of skin contact : Wash with water and soap as a precaution. Get medical attention if symptoms occur. In case of eye contact : Flush eyes with water as a precaution. Get medical attention if irritation develops and persists. If swallowed : If swallowed, DO NOT induce vomiting. Get medical attention if symptoms occur. Rinse mouth thoroughly with water. Most important symptoms and effects, both acute and delayed : None known. Protection of first-aiders : No special precautions are necessary for first aid responders. Notes to physician : Treat symptomatically and supportively. SECTION 5. FIRE-FIGHTING MEASURES Suitable extinguishing media : Water spray Alcohol-resistant foam Carbon dioxide (CO2) Dry chemical Unsuitable extinguishing media : None known. Specific hazards during fire fighting : Exposure to combustion products may be a hazard to health. Hazardous combustion prod- ucts : Carbon oxides Silicon oxides Formaldehyde Specific extinguishing meth- ods : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Use water spray to cool unopened containers. Remove undamaged containers from fire area if it is safe to do so. Evacuate area. Special protective equipment for fire-fighters : Wear self-contained breathing apparatus for firefighting if necessary. Use personal protective equipment. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- : Follow safe handling advice and personal protective equipment recommendations. SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 3 / 11 gency procedures Environmental precautions : Discharge into the environment must be avoided. Prevent further leakage or spillage if safe to do so. Retain and dispose of contaminated wash water. Local authorities should be advised if significant spillages cannot be contained. Methods and materials for containment and cleaning up : Soak up with inert absorbent material. For large spills, provide diking or other appropriate containment to keep material from spreading. If diked material can be pumped, store recovered material in appropriate container. Clean up remaining materials from spill with suitable absorbent. Local or national regulations may apply to releases and disposal of this material, as well as those materials and items employed in the cleanup of releases. You will need to determine which regulations are applicable. Sections 13 and 15 of this SDS provide information regarding certain local or national requirements. SECTION 7. HANDLING AND STORAGE Technical measures : See Engineering measures under EXPOSURE CONTROLS/PERSONAL PROTECTION section. Local/Total ventilation : Use only with adequate ventilation. Advice on safe handling : Handle in accordance with good industrial hygiene and safety practice. Take care to prevent spills, waste and minimize release to the environment. Conditions for safe storage : Keep in properly labeled containers. Store in accordance with the particular national regulations. Materials to avoid : Do not store with the following product types: Strong oxidizing agents SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Ingredients with workplace control parameters Ingredients CAS-No. Value type (Form of exposure) Control parame- ters / Permissible concentration Basis Silicon dioxide 7631-86-9 TWA (Dust) 20 Million particles per cubic foot (Silica) OSHA Z-3 TWA (Dust) 80 mg/m3 / %SiO2 OSHA Z-3 SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 4 / 11 (Silica) TWA 6 mg/m (Silica) NIOSH REL These substance(s) are inextricably bound in the product and therefore do not contribute to a dust inhalation hazard. Silicon dioxide Engineering measures : Processing may form hazardous compounds (see section 10). Ensure adequate ventilation, especially in confined areas. Minimize workplace exposure concentrations. Personal protective equipment Respiratory protection : No personal respiratory protective equipment normally required. Hand protection Remarks : Wash hands before breaks and at the end of workday. Eye protection : Wear the following personal protective equipment: Safety glasses Skin and body protection : Skin should be washed after contact. Hygiene measures : Ensure that eye flushing systems and safety showers are located close to the working place. When using do not eat, drink or smoke. Wash contaminated clothing before re-use. These precautions are for room temperature handling. Use at elevated temperature or aerosol/spray applications may require added precautions. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : paste Color : colorless Odor : Acetic acid Odor Threshold : No data available pH : Not applicable Melting point/freezing point : No data available Initial boiling point and boiling range : Not applicable Flash point : Not applicable SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 5 / 11 Evaporation rate : Not applicable Flammability (solid, gas) : Not classified as a flammability hazard Self-ignition : The substance or mixture is not classified as pyrophoric. The substance or mixture is not classified as self heating. Upper explosion limit / Upper flammability limit : No data available Lower explosion limit / Lower flammability limit : No data available Vapor pressure : Not applicable Relative vapor density : No data available Relative density : 1.04 Solubility(ies) Water solubility : No data available Partition coefficient: n- octanol/water : No data available Autoignition temperature : No data available Decomposition temperature : No data available Viscosity Viscosity, dynamic : Not applicable Explosive properties : Not explosive Oxidizing properties : The substance or mixture is not classified as oxidizing. Molecular weight : No data available Particle size : No data available SECTION 10. STABILITY AND REACTIVITY Reactivity : Not classified as a reactivity hazard. Chemical stability : Stable under normal conditions. Possibility of hazardous reac- tions : Use at elevated temperatures may form highly hazardous compounds. Can react with strong oxidizing agents. Acetic acid is formed upon contact with water or humid air. Hazardous decomposition products will be formed at elevated temperatures. SAFETY DATA SHEET DOWSIL TB/TL/CER Sealant Clear Version 3.0 Revision Date: 10/16/2017 SDS Number: 1291572-00010 Date of last issue: 04/24/2017 Date of first issue: 02/10/2015 6 / 11 Conditions to avoid : None known. Incompatible materials : Oxidizing agents Hazardous decomposition products Thermal decomposition : Formaldehyde SECTION 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Skin contact Ingestion Eye contact Acute toxicity Not classified based on available information. Ingredients: Silicon dioxide: Acute oral toxicity : LD50 (Rat): > 3,300 mg/kg
Assessment: The substance or mixture has no acute oral tox-
icity
Remarks: Information taken from reference works and the
literature.

Acute inhalation toxicity

: LC50 (Rat): > 2.08 mg/l
Exposure time: 4 h
Test atmosphere: dust/mist
Assessment: The substance or mixture has no acute inhala-
tion toxicity
Remarks: Information taken from reference works and the
literature.

Acute dermal toxicity

: LD50 (Rabbit): > 5,000 mg/kg
Assessment: The substance or mixture has no acute dermal
toxicity
Remarks: Information taken from reference works and the
literature.

Skin corrosion/irritation
Not classified based on available information.
Ingredients:
Silicon dioxide:
Result: No skin irritation
Remarks: Information taken from reference works and the literature.

Serious eye damage/eye irritation
Not classified based on available information.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

7 / 11
Ingredients:
Silicon dioxide:
Result: No eye irritation
Remarks: Information taken from reference works and the literature.

Respiratory or skin sensitization
Skin sensitization
Not classified based on available information.
Respiratory sensitization
Not classified based on available information.
Ingredients:
Silicon dioxide:
Assessment: Does not cause skin sensitization.

Test Type: Skin: test type not specified
Species: Guinea pig
Result: negative
Remarks: Information taken from reference works and the literature.

Germ cell mutagenicity
Not classified based on available information.
Ingredients:
Silicon dioxide:
Genotoxicity in vitro

: Result: negative
Remarks: Information taken from reference works and the
literature.

Genotoxicity in vivo

: Application Route: Ingestion
Result: negative
Remarks: Information taken from reference works and the
literature.

Germ cell mutagenicity –
Assessment

: Animal testing did not show any mutagenic effects.

Carcinogenicity
Not classified based on available information.
IARC

No ingredient of this product present at levels greater than or
equal to 0.1% is identified as probable, possible or confirmed
human carcinogen by IARC.

OSHA

No component of this product present at levels greater than or
equal to 0.1% is on OSHA s list of regulated carcinogens.

NTP

No ingredient of this product present at levels greater than or
equal to 0.1% is identified as a known or anticipated carcinogen
by NTP.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

8 / 11

Reproductive toxicity
Not classified based on available information.
STOT-single exposure
Not classified based on available information.
STOT-repeated exposure
Not classified based on available information.
Aspiration toxicity
Not classified based on available information.
SECTION 12. ECOLOGICAL INFORMATION
Ecotoxicity
No data available
Persistence and degradability
No data available
Bioaccumulative potential
No data available
Mobility in soil
No data available
Other adverse effects
No data available
SECTION 13. DISPOSAL CONSIDERATIONS
Disposal methods
Resource Conservation and
Recovery Act (RCRA)
: This product has been evaluated for RCRA characteristics
and does not meet the criteria of hazardous waste if discarded
in its purchased form.

Waste from residues : Dispose of in accordance with local regulations.

Contaminated packaging : Empty containers should be taken to an approved waste
handling site for recycling or disposal.
If not otherwise specified: Dispose of as unused product.

SECTION 14. TRANSPORT INFORMATION
International Regulations
UNRTDG
Not regulated as a dangerous good
IATA-DGR
Not regulated as a dangerous good
IMDG-Code

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

9 / 11
Not regulated as a dangerous good
Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code
Not applicable for product as supplied.
Domestic regulation
49 CFR
Not regulated as a dangerous good
SECTION 15. REGULATORY INFORMATION
EPCRA – Emergency Planning and Community Right-to-Know
CERCLA Reportable Quantity
Ingredients CAS-No. Component RQ
(lbs)
Calculated product RQ
(lbs)
Acetic acid 64-19-7 5000 *
Acetic anhydride 108-24-7 5000 *
*: Calculated RQ exceeds reasonably attainable upper limit.
SARA 304 Extremely Hazardous Substances Reportable Quantity
This material does not contain any components with a section 304 EHS RQ.
SARA 302 Extremely Hazardous Substances Threshold Planning Quantity
This material does not contain any components with a section 302 EHS TPQ.
SARA 311/312 Hazards

: No SARA Hazards

SARA 313

: This material does not contain any chemical components with
known CAS numbers that exceed the threshold (De Minimis)
reporting levels established by SARA Title III, Section 313.

US State Regulations
Pennsylvania Right To Know
Dimethyl siloxane, hydroxy-terminated 70131-67-8
Silicon dioxide 7631-86-9
Acetic acid 64-19-7
Acetic anhydride 108-24-7
California Prop. 65
This product does not contain any chemicals known to the State of California to cause cancer,
birth, or any other reproductive defects.
California Permissible Exposure Limits for Chemical Contaminants
Silicon dioxide 7631-86-9
The ingredients of this product are reported in the following inventories:
NZIoC

: All ingredients listed or exempt.

AICS

: All ingredients listed or exempt.

IECSC

: All ingredients listed or exempt.

PICCS : All ingredients listed or exempt.

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

10 / 11

DSL

: All chemical substances in this product comply with the CEPA
1999 and NSNR and are on or exempt from listing on the
Canadian Domestic Substances List (DSL).

REACH

: For purchases from Dow Chemical EU legal entities, all
ingredients are currently pre/registered or exempt under
REACH. Please refer to section 1 for recommended uses. For
purchases from non-EU Dow Chemical legal entities with the
intention to export into EEA please contact your DC
representative/local office.

TSCA

: All chemical substances in this product are either listed on the
TSCA Inventory or are in compliance with a TSCA Inventory
exemption.

TCSI

: All ingredients listed or exempt.

SECTION 16. OTHER INFORMATION
Further information
NFPA: HMIS IV:

HMIS ratings are based on a 0-4 rating
scale, with 0 representing minimal ha-
zards or risks, and 4 representing signifi-
cant hazards or risks. The “*” represents
a chronic hazard, while the “/” represents
the absence of a chronic hazard.

Full text of other abbreviations
NIOSH REL : USA. NIOSH Recommended Exposure Limits
OSHA Z-3 : USA. Occupational Exposure Limits (OSHA) – Table Z-3 Min-
eral Dusts
NIOSH REL / TWA : Time-weighted average concentration for up to a 10-hour
workday during a 40-hour workweek
OSHA Z-3 / TWA : 8-hour time weighted average

AICS – Australian Inventory of Chemical Substances; ASTM – American Society for the Testing of
Materials; bw – Body weight; CERCLA – Comprehensive Environmental Response, Compensation,
and Liability Act; CMR – Carcinogen, Mutagen or Reproductive Toxicant; DIN – Standard of the
German Institute for Standardisation; DOT – Department of Transportation; DSL – Domestic Sub-
stances List (Canada); ECx – Concentration associated with x% response; EHS – Extremely Ha-

Flammability

Health

Instability

0
1
0

Special hazard.
FLAMMABILITY
1
PHYSICAL HAZARD
HEALTH
0

/ 0

SAFETY DATA SHEET

DOWSIL TB/TL/CER Sealant Clear

Version
3.0
Revision Date:
10/16/2017
SDS Number:
1291572-00010
Date of last issue: 04/24/2017
Date of first issue: 02/10/2015

11 / 11
zardous Substance; ELx – Loading rate associated with x% response; EmS – Emergency Sche-
dule; ENCS – Existing and New Chemical Substances (Japan); ErCx – Concentration associated
with x% growth rate response; ERG – Emergency Response Guide; GHS – Globally Harmonized
System; GLP – Good Laboratory Practice; HMIS – Hazardous Materials Identification System;
IARC – International Agency for Research on Cancer; IATA – International Air Transport Associa-
tion; IBC – International Code for the Construction and Equipment of Ships carrying Dangerous
Chemicals in Bulk; IC50 – Half maximal inhibitory concentration; ICAO – International Civil Avia-
tion Organization; IECSC – Inventory of Existing Chemical Substances in China; IMDG – Interna-
tional Maritime Dangerous Goods; IMO – International Maritime Organization; ISHL – Industrial
Safety and Health Law (Japan); ISO – International Organisation for Standardization; KECI – Ko-
rea Existing Chemicals Inventory; LC50 – Lethal Concentration to 50 % of a test population; LD50
– Lethal Dose to 50% of a test population (Median Lethal Dose); MARPOL – International Conven-
tion for the Prevention of Pollution from Ships; MSHA – Mine Safety and Health Administration;
n.o.s. – Not Otherwise Specified; NFPA – National Fire Protection Association; NO(A)EC – No Ob-
served (Adverse) Effect Concentration; NO(A)EL – No Observed (Adverse) Effect Level; NOELR –
No Observable Effect Loading Rate; NTP – National Toxicology Program; NZIoC – New Zealand
Inventory of Chemicals; OECD – Organization for Economic Co-operation and Development;
OPPTS – Office of Chemical Safety and Pollution Prevention; PBT – Persistent, Bioaccumulative
and Toxic substance; PICCS – Philippines Inventory of Chemicals and Chemical Substances;
(Q)SAR – (Quantitative) Structure Activity Relationship; RCRA – Resource Conservation and Re-
covery Act; REACH – Regulation (EC) No 1907/2006 of the European Parliament and of the
Council concerning the Registration, Evaluation, Authorisation and Restriction of Chemicals; RQ –
Reportable Quantity; SADT – Self-Accelerating Decomposition Temperature; SARA – Superfund
Amendments and Reauthorization Act; SDS – Safety Data Sheet; TCSI – Taiwan Chemical Sub-
stance Inventory; TSCA – Toxic Substances Control Act (United States); UN – United Nations;
UNRTDG – United Nations Recommendations on the Transport of Dangerous Goods; vPvB –
Very Persistent and Very Bioaccumulative

Sources of key data used to
compile the Material Safety
Data Sheet
: Internal technical data, data from raw material SDSs, OECD
eChem Portal search results and European Chemicals Agen-
cy, http://echa.europa.eu/

Revision Date : 10/16/2017

Items where changes have been made to the previous version are highlighted in the body of this
document by two vertical lines.

The information provided in this Safety Data Sheet is correct to the best of our knowledge,
information and belief at the date of its publication. The information is designed only as a
guidance for safe handling, use, processing, storage, transportation, disposal and release and
shall not be considered a warranty or quality specification of any type. The information provided
relates only to the specific material identified at the top of this SDS and may not be valid when the
SDS material is used in combination with any other materials or in any process, unless specified
in the text. Material users should review the information and recommendations in the specific
context of their intended manner of handling, use, processing and storage, including an
assessment of the appropriateness of the SDS material in the user s end product, if applicable.

US / Z8

17CHA95_SDS.pdf

INDEX

17CHA95
17CHA95-G
17CHA95-Q

SAFETY DATA SHEET
Date Issued : 11/5/2013
MSDS No : CHALLENGE 95
CHALLENGE 95
1. PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: CHALLENGE 95
GENERAL USE: Release agent
MANUFACTURER 24 HR. EMERGENCY TELEPHONE NUMBERS
BJB Enterprises, Inc.
14791 Franklin Avenue
Tustin, CA 92780
Customer Service Number: (714) 734-8450
Fax: (714) 734-8929

CHEMTREC (US Transportation): (800) 424-9300
or (703) 527-3887 CCN# 2820
2. HAZARDS IDENTIFICATION
GHS CLASSIFICATIONS
Health:
Skin Irritation, Category 2
Eye Irritation, Category 2A
Mutagenicity, Category 1
Carcinogenicity, Category 1
Reproductive Toxicity, Category 2
Target Organ Toxicity (Single exposure), Category 3
Target Organ Toxicity (Repeated exposure), Category 2
Aspiration Hazard, Category 1
Environmental:
Chronic Hazards to the Aquatic Environment, Category 3
Physical:
Flammable Liquids, Category 2
GHS LABEL
Flame Exclamation
mark
Health hazard
SIGNAL WORD: DANGER
HAZARD STATEMENTS
H225: Highly flammable liquid and vapour.
H315: Causes skin irritation.
H319: Causes serious eye irritation.
H340: May cause genetic defects .
H350: May cause cancer .
H361: Suspected of damaging fertility or the unborn child .
H336: May cause drowsiness or dizziness.
H373: May cause damage to organs through prolonged or repeated exposure .
Page 1 of 8

H304: May be fatal if swallowed and enters airways.
H412: Harmful to aquatic life with long lasting effects.
PRECAUTIONARY STATEMENT(S)
Prevention:
P210: Keep away from heat/sparks/open flames/hot surfaces. No smoking.
P233: Keep container tightly closed.
P240: Ground/bond container and receiving equipment.
P241: Use explosion-proof electrical/ventilating/lighting/ / equipment.
P242: Use only non-sparking tools.
P243: Take precautionary measures against static discharge.
P201: Obtain special instructions before use.
P202: Do not handle until all safety precautions have been read and understood.
P260: Do not breathe dust/fume/gas/mist/vapours/spray.
P271: Use only outdoors or in a well-ventilated area.
P280: Wear protective gloves/protective clothing/eye protection/face protection.
P264: Wash thoroughly after handling.
P273: Avoid release to the environment.
Response:
P303+P361+P353: IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
P370+P378: In case of fire: Use for extinction.
P302+P352: IF ON SKIN: Wash with plenty of soap and water.
P321: Specific treatment (see on this label).
P332+P313: If skin irritation occurs: Get medical advice/attention.
P362: Take off contaminated clothing and wash before reuse.
P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing.
P337+P313: If eye irritation persists: Get medical advice/attention.
P308+P313: IF exposed or concerned: Get medical advice/attention.
P304+P340: IF INHALED: Remove to fresh air and keep at rest in a position comfortable for breathing.
P312: Call a POISON CENTER or doctor/physician if you feel unwell.
P301+P310: IF SWALLOWED: Immediately call a POISON CENTER or doctor/physician.
P331: Do NOT induce vomiting.
Storage:
P403+P233: Store in a well-ventilated place. Keep container tightly closed.
P235: Keep cool.
P405: Store locked up.
Disposal:
P501: Dispose of contents/container in accordance with local/regional/national/international regulations.
EMERGENCY OVERVIEW
PHYSICAL APPEARANCE AND ODOR: Yellow liquid with a solvent odor.
IMMEDIATE CONCERNS: Warning! Flammable liquid and vapor. Harmful if swallowed. DO NOT induce vomiting if swallowed.
Harmful if inhaled. Causes serious eye irritation. Causes skin irritation. Keep away from heat, sparks, and flames. Vapors can travel to a
source of ignition and flash back.
POTENTIAL HEALTH EFFECTS
EYES: Causes serious eye irritation.
SKIN: Causes skin irritation. Frequent or prolonged contact may defat and dry the skin, leading to discomfort and dermatitis.
INGESTION: Harmful if swallowed. Aspiration hazard. This material can enter the lungs during swallowing or vomiting and cause lung
inflammation and damage. It may also cause irritation to the mucous membranes of the mouth, throat, and digestive tract.
INHALATION: Harmful if inhaled. Irritating to respiratory system. Prolonged inhalation my be harmful.
REPRODUCTIVE TOXICITY
REPRODUCTIVE EFFECTS: This product contains ingredients that are considered to cause reproductive harm.
CARCINOGENICITY: This product contains ingredients that are considered to be probable or suspected human carcinogens.
Page 2 of 8
CHALLENGE 95

MEDICAL CONDITIONS AGGRAVATED: Pre-existing eye, skin, and respiratory conditions may be aggravated by exposure.
ROUTES OF ENTRY: Eye and skin contact, inhalation of vapors, or accidental ingestion.
TARGET ORGANS: Contains material which may cause damage to the following organs: respiratory tract, kidneys, liver, central nervous
system (CNS).
3. COMPOSITION / INFORMATION ON INGREDIENTS
Chemical Name Wt.% CAS
Toluene 40 – 80108-88-3
2-propanol 0 – 20 67-63-0
1,2,4-trimethylbenzene 5 – 10 95-63-6
Stoddard solvent 5 – 108052-41-3
4. FIRST AID MEASURES
EYES: Immediately rinse with water. Remove contact lenses. Hold eyelids apart and flush eyes with water for at least 15 minutes. Get
immediate medical attention.
SKIN: Immediately wash skin with soap and plenty of water. Remove contaminated clothing. Get medical attention if irritation or rash
develops. Wash clothing before reuse.
INGESTION: Aspiration hazard. If swallowed, DO NOT induce vomiting. If vomiting occurs spontaneously, keep head below hips to prevent
aspiration of liquid into lungs. Never give anything by mouth to an unconscious person. Get medical attention immediately.
INHALATION: Remove to fresh air. If not breathing, give artificial respiration or give oxygen by trained personnel. Seek immediate medical
attention.
CHRONIC TOXICITY
CHRONIC EFFECTS: May cause damage to the liver and kidneys. Frequent or prolonged contact my defat and dry the skin, leading to
discomfort and dermatitis.
NOTES TO PHYSICIAN: Symptomatic and supportive therapy as needed. Following severe exposure medical follow-up should be
monitored for at least 48 hours.
5. FIRE FIGHTING MEASURES
GENERAL HAZARD: Flammable liquid and vapor.
EXTINGUISHING MEDIA: Water spray, carbon dioxide, dry chemical, or foam.
HAZARDOUS COMBUSTION PRODUCTS: Carbon monoxide and carbon dioxide.
EXPLOSION HAZARDS: Temperatures at or above the flash point could generate combustible mixtures. Avoid all ignition sources. “Empty”
containers retain product residue (liquid and/or vapor) and can be dangerous. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER,
DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FL AME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES O F
IGNITION; THEY MAY EXPLODE AND CAUSE INJURY OR DEAT H. Empty drums should be completely drained, properly bunged and
promptly returned to a drum reconditioner, or properly disposed of.
FIRE FIGHTING PROCEDURES: Remove containers from the fire area if possible. Do not release runoff from fire control methods to
sewers or waterways.
FIRE FIGHTING EQUIPMENT: Firefighters should wear positive pressure self-contained breathing apparatus (SCBA) and consider use of
unmanned hose holders or monitor nozzles for fighting large fires.
SENSITIVE TO STATIC DISCHARGE: This material can accumulate static charges which can cause an incendiary electrical discharge.
6. ACCIDENTAL RELEASE MEASURES
SMALL SPILL: Eliminate sources of ignition. Evacuate the area. Clean-up should only be performed by trained personnel. People dealing
with a major spill should wear full protective clothing including appropriate respiratory protection. Prevent product spill from entering sewers
or waterways. Neutralize small spills with a decontaminant.
LARGE SPILL: Contain and absorb large spills onto an inert, non-flammable adsorbent carrier (earth or sand). Do not use combustible
Page 3 of 8
CHALLENGE 95

materials such as saw dust. Use only spark resistant and explosion proof recovery devices. Shovel into open-top drums or plastic bags for
further decontamination, if necessary. Wash the spill area clean with a liquid decontaminant. Remove and properly dispose of residues.
Notify applicable government authorities if release is reportable. (See CERCLA in Section 15).
ENVIRONMENTAL PRECAUTIONS
WATER SPILL: Do not discharge into drains or rivers.
GENERAL PROCEDURES: Refer to section 8 of SDS for personal protection details.
RELEASE NOTES: Composition and extent of any spill should be evaluated against local regulations and reported to the proper agencies, if
necessary.
7. HANDLING AND STORAGE
GENERAL PROCEDURES: Flammable liquid. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Avoid
breathing vapor over open containers. Avoid open container exposure to damp air. Avoid breathing aerosols, mists, and vapors.
HANDLING: Use in a well ventilated area. Avoid heat, sparks, and open flames. Avoid breathing vapor and contact with eyes, skin, and
clothing. Use appropriate personal protective equipment as specified in Section 8. Handle and use in a manner consistent with good
industrial/manufacturing techniques and practices.
STORAGE: Store in a cool, well-ventilated, dry place, away from excessive heat in the original or similar container. Avoid sources of ignition
and incompatible materials. Keep containers tightly sealed. Avoid unnecessary contact.
SHELF LIFE: 12 months from date of shipment under manufacturers recommended storage conditions.
ELECTROSTATIC ACCUMULATION HAZARD: This material can accumulate static charges which can cause an incendiary electrical
discharge. Use proper bonding and/or grounding procedure.
8. EXPOSURE CONTROLS / PERSONAL PROTECTION
EXPOSURE GUIDELINES
OSHA HAZARDOUS COMPONENTS (29 CFR1910.1200)
EXPOSURE LIMITS
OSHA PEL ACGIH TLV SupplierOEL
Chemical Name ppm mg/m
3
ppm mg/m
3
ppm mg/m
3
Toluene
TWA 200 NE 50 188 100
[1]
375
[1]
STEL 300 NE NE NE 150
[1]
560
[1]
2-propanol
TWA 400 980 200 490 NE NE
STEL NE NE 400 960 NE NE
1,2,4-trimethylbenzene
TWA NE NE 25 123 25
[1]
125
[1]
STEL NE NE NE NE NE NE
Stoddard solvent
TWA 500 2900 100 572 350
[1]
NE
[1]
STEL NE NE NE NE NE NE
OSHA TABLE COMMENTS:
1. NIOSH REL
ENGINEERING CONTROLS: Use process enclosures, local exhaust ventilation, or other engineering controls to control airborne levels
below recommended exposure limits.
PERSONAL PROTECTIVE EQUIPMENT
EYES AND FACE: Safety goggles or glasses are recommended. Plastic face shields should be used for complete face protection to protect
against possible splashing or spraying of material. ANSI Z87.1 or approved equivalent.
SKIN: Chemical-resistant gloves and chemical goggles, face-shield, and synthetic apron or coveralls should be used to prevent contact with
eyes, skin, or clothing. Wear nitrile or neoprene gloves. Chemical resistant gloves lined with polyethylene offer maximum protection.
RESPIRATORY: Exhaust ventilation recommended. An organic vapor cartridge or fresh air supplied respirator (NIOSH approved) may be
Page 4 of 8
CHALLENGE 95

necessary for certain applications. Consider the type of application, environmental concentrations, and other materials being used
concurrently when determining respirator use and selection. Observe OSHA regulations for respirator use (29 CFR 1910.134).
PROTECTIVE CLOTHING: Protective clothing should be selected and used in accordance with ‘Guidelines for the Selection of Chemical
Protective Clothing’ published by ACGIH.
WORK HYGIENIC PRACTICES: Contaminated clothing should be changed and washed before reuse. Eating, drinking and smoking in
immediate work area should be prohibited. Wash hands before eating.
OTHER USE PRECAUTIONS: Facilities storing or utilizing this material should be equipped with an eyewash facility and a safety shower.
Training is important. Follow all label precautions.
9. PHYSICAL AND CHEMICAL PROPERTIES
PHYSICAL STATE: Liquid
ODOR: Solvent
COLOR: Yellow
pH: Not Applicable
FLASHPOINT AND METHOD: 4 C (39.2 F) Closed Cup (Toluene)
VAPOR PRESSURE: Not Established
VAPOR DENSITY: Not Established
BOILING POINT: Not Established
SOLUBILITY IN WATER: Negligible
SPECIFIC GRAVITY: Not Established
VISCOSITY: Not Established
10. STABILITY AND REACTIVITY
STABILITY: This product is stable under the recommended storage conditions.
POLYMERIZATION: Will not occur.
CONDITIONS TO AVOID: Avoid heat, sparks, open flames and other ignition sources.
POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous reactions will not occur under normal transport or storage conditions.
HAZARDOUS DECOMPOSITION PRODUCTS: Carbon monoxide and carbon dioxide.
INCOMPATIBLE MATERIALS: Strong acids, strong bases, and strong oxidizing agents.
11. TOXICOLOGICAL INFORMATION
TOXICITY TO ANIMALS
Chemical Name
ORAL LD50
(rat)
DERMAL LD50
(rabbit)
INHALATION
LC
50 (rat)
Toluene 636 mg/kg 2 to 14 g/kg 26700 ppm (1h)
2-propanol 5800 mg/kg 16.4 ml/kg 12000 ppm (8 h)
1,2,4-trimethylbenzene 12.7 g/kg Not Established 18 g/m3
Stoddard solvent > 6000 mg/kg > 3000 ml/kg 5500 mg/m3 (4 h)
CHRONIC EFFECTS: Prolonged inhalation may be harmful. Prolonged or repeated exposure may cause lung injury. Prolonged or repeated
exposure may cause liver, kidney and central nervous system damage.
CARCINOGENICITY
Page 5 of 8
CHALLENGE 95

Chemical Name
IARC
Status
Toluene 3
2-propanol 3
IARC: This product contains substances that are not classifiable as carcinogens to humans.
IRRITATION: Causes eye, skin, and respiratory irritation.
SENSITIZATION: Risk of sensitization or allergic reactions among sensitive individuals.
NEUROTOXICITY: Central and/or peripheral nervous system damage. May cause drowsiness or dizziness.
REPRODUCTIVE EFFECTS: Suspected of damaging fertility. Suspected of damaging the unborn child.
TARGET ORGANS: Contains material which may cause damage to the following organs: respiratory tract, kidneys, liver, central nervous
system (CNS).
12. ECOLOGICAL INFORMATION
ENVIRONMENTAL DATA: This product may cause risk of hazardous effects to the environment.
ECOTOXICOLOGICAL INFORMATION: Harmful to aquatic organisms, may cause long-term adverse effects in the aquatic environment.
Avoid release to the environment.
BIOACCUMULATION/ACCUMULATION: No data available
DISTRIBUTION: No data available
CHEMICAL FATE INFORMATION: No data available
13. DISPOSAL CONSIDERATIONS
DISPOSAL METHOD: The generation of waste should be avoided or minimized wherever possible. Empty containers or liners may retain
some product residues. This material and its container must be disposed of in a safe way. Dispose of surplus and non-recyclable products via
a licensed waste disposal contractor. Disposal of this product, solutions and any by-products should at all times comply with the requirements
of environmental protections and waste disposal legislation and any regional local authority requirements. Avoid dispersal of spilled material
and runoff and contact with soil, waterways, drains and sewers.
EMPTY CONTAINER: Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without
proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty
containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with
governmental regulations. DO NOT PRESSURIZE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CO NTAINERS
TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHE R SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE
INJURY OR DEATH.
14. TRANSPORT INFORMATION
DOT (DEPARTMENT OF TRANSPORTATION) LAND
PROPER SHIPPING NAME: Flammable liquids, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
PRIMARY HAZARD CLASS/DIVISION: 3
UN/NA NUMBER: UN1993
PACKING GROUP: II
ERG CODE: 128
LABEL: Flammable liquid
AIR (ICAO/IATA)
SHIPPING NAME: Flammable liquid, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
UN/NA NUMBER: UN1993
PRIMARY HAZARD CLASS/DIVISION: 3
Page 6 of 8
CHALLENGE 95

PACKING GROUP: II
ERG CODE: 3H
LABEL: Flammable liquid
VESSEL (IMO/IMDG)
SHIPPING NAME: Flammable liquid, n.o.s.
TECHNICAL NAME: (toluene, mineral spirits)
UN/NA NUMBER: UN1993
PRIMARY HAZARD CLASS/DIVISION: 3
PACKING GROUP: II
LABEL: Flammable liquid
SPECIAL PROVISIONS: EmS: F-E, S-E
15. REGULATORY INFORMATION
UNITED STATES
SARA TITLE III (SUPERFUND AMENDMENTS AND REAUTHORIZ ATION ACT)
311/312 HAZARD CATEGORIES: Acute health hazard. Chronic health hazard. Fire hazard.
313 REPORTABLE INGREDIENTS: This product contains the following substances subject to the reporting requirements of Section
313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 and 40 CFR Part 372:
EPCRA SECTION 313 SUPPLIER NOTIFICATION
Chemical Name Wt.% CAS
Toluene 40 – 80108-88-3
2-propanol 0 – 2067-63-0
1,2,4-trimethylbenzene 5 – 1095-63-6
CERCLA (COMPREHENSIVE RESPONSE, COMPENSATION, AND L IABILITY ACT)
CERCLA REGULATORY: For this/these chemicals, release of more than the Reportable Quantity to the environment in a 24-hour
period requires notification to the National Response Center (800-424-8802 or 202-426-2675):
Chemical Name Wt.%
CERCLA
RQ
Toluene 40 – 801,000 lbs.
TSCA (TOXIC SUBSTANCE CONTROL ACT)
TSCA REGULATORY: This product contains chemical(s) subject to TSCA Section 12(b) export notification:
None
TSCA STATUS: This product or its components are listed in or exempt from the TSCA inventory requirements.
OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION (OSHA )
29 CFR1910.119—PROCESS SAFETY MANAGEMENT OF HIGHL Y HAZARDOUS CHEMICALS: None of the chemicals in
this product are considered highly hazardous by OSHA.
CALIFORNIA PROPOSITION 65: This product contains chemical(s) which are known to the State of California to cause cancer, birth
defects or other reproductive harm, and may be subject to the requirements of California Proposition 65 (CA Health & Safety Code
Section 25249.5):
Chemical Name Wt.% Listed
Toluene 40 – 80
Cancer
Developmental Toxicity
OSHA HAZARD COMM. RULE: The contents of the MSDS comply with the OSHA Hazard Communication Standard 29 CFR
1910.1200.
Page 7 of 8
CHALLENGE 95

CANADA
WHMIS HAZARD SYMBOL AND CLASSIFICATION
Flammable
Liquid
Toxic
WHMIS CLASSIFICATION
Class B2: Flammable liquid
Class D-2A: Poisonous and infectious material (Very toxic).
Class D-2B: Poisonous and infectious material (Toxic).
WHMIS HEALTH EFFECTS CRITERIA
D2A – Teratogenicity and embryotoxicity
D2B – Skin irritation
D2B – Eye irritation
WHMIS (WORKPLACE HAZARDOUS MATERIALS INFORMATION SY STEM): This product has been classified according to the
hazard criteria of the CPR and the MSDS contains all the information required by the CPR.
DOMESTIC SUBSTANCE LIST (INVENTORY): All components in this product are listed in or exempted from the Domestic
Substances List (DSL) or the Non-Domestic Substances List (NDSL).
16. OTHER INFORMATION
REASON FOR ISSUE: New Issue
HMIS RATING
HEALTH * 2
FLAMMABILITY 3
PHYSICAL HAZARD 1
PERSONAL PROTECTION X
NFPA CODES

3
2 1

HMIS RATINGS NOTES: Personal Protection: See Section 8
MANUFACTURER DISCLAIMER: This information is furnished without warranty, expressed or implied, except that is accurate to the best
knowledge of BJB Enterprises, Inc. The data on this sheet relates only to the specific material designated herein. BJB Enterprises, Inc.
assumes no legal responsibility for use or reliance upon this data.
Page 8 of 8
CHALLENGE 95