25HP8204BF_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8200 Series B-Side
Safety Data Sheet dated: 7/28/2023 – version 6
Date of first edition: 1/16/2023
1. IDENTIFICATION
Product identifier
Mixture identification:
Trade name:HP 8200 Series B-Side
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use:N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company:ETECO INC.
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable:N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION
Classification of the chemical
Label elements
Skin Sensitization, Category 1 May cause an allergic skin reaction.
Specific target organ toxicity following single exposure,
Category 1
Causes damage to organs.
Specific target organ toxicity following repeated exposure,
Category 2
May cause damage to organs through prolonged or repeated
exposure.
Hazard pictograms and Signal Word
Danger
Hazard statements
H317 May cause an allergic skin reaction.
H370 Causes damage to organs.
H373 May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash … Thoroughly after handling.
P270 Do not eat, drink or smoke when using this product.
P272 Contaminated work clothing must not be allowed out of the workplace.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P302+P352 IF ON SKIN: Wash with plenty of water/
P308+P311 IF exposed or concerned: Call a POISON CENTER/doctor/
Page n. of1 87/28/2023 Production Name HP 8200 Series B-SideDate

Hazards not otherwise classified identified during the classification process:
None
Additional classification information
HMIS Health:0 = MINIMAL
HMIS Flammability:0 = Not Combustible
HMIS Reactivity:0 = MINIMAL
HMIS P.P.E.:Safety glasses, gloves
NFPA Health:0 = MINIMAL
NFPA Flammability:0 = Not Combustible
NFPA Reactivity:0 = MINIMAL
NFPA Special Risk:NONE
P314 Get medical advice/attention if you feel unwell.
P321 Specific treatment (see … On this label).
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P363 Wash contaminated clothing before reuse.
P405 Store locked up.
P501 Dispose of contents/container to …
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
N.A.
Mixtures
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification:
List of components
Qty Name Ident. Numb. Classification Registration Number
< 5 % ETHOXYLATED, PROPOXYLATED ETHYLENEDIAMINE CAS:26316-40-5 Eye Irrit. 2A, H319; Skin Sens. 1, H317 < 5 % Diethylene glycol CAS:111-46-6 Acute Tox. 4, H302; STOT RE 2, H373 < 5 % METHYL FORMATE CAS:107-31-3 Flam. Liq. 1, H224; Acute Tox. 3, H301; Acute Tox. 3, H311; Acute Tox. 3, H331; Eye Irrit. 2A, H319; STOT SE 3, H335; STOT SE 1, H370 The actual concentration of the components listed above is withheld as a trade secret. 4. FIRST AID MEASURES Description of first aid measures In case of skin contact: Immediately take off all contaminated clothing. Remove contaminated clothing immediatley and dispose off safely. In case of eyes contact: Wash immediately with water. In case of Ingestion: Do not induce vomiting, get medical attention showing the SDS and label hazardous. In case of Inhalation: Remove casualty to fresh air and keep warm and at rest. Most important symptoms/effects, acute and delayed N.A. Indication of any immediate medical attention and special treatment needed In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible). 5. FIRE-FIGHTING MEASURES Page n. of2 87/28/2023 Production Name HP 8200 Series B-SideDate Extinguishing media Suitable extinguishing media: Water. Carbon dioxide (CO2). Unsuitable extinguishing media: None in particular. Specific hazards arising from the chemical Do not inhale explosion and combustion gases. Burning produces heavy smoke. Hazardous combustion products:N.A. Explosive properties:N.A. Oxidizing properties:N.A. Special protective equipment and precautions for fire-fighters Use suitable breathing apparatus . Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Move undamaged containers from immediate hazard area if it can be done safely. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Wear personal protection equipment. Remove persons to safety. See protective measures under point 7 and 8. Methods and material for containment and cleaning up Suitable material for taking up: absorbing material, organic, sand Wash with plenty of water. 7. HANDLING AND STORAGE Precautions for safe handling Avoid contact with skin and eyes, inhaltion of vapours and mists. Don't use empty container before they have been cleaned. Before making transfer operations, assure that there aren't any incompatible material residuals in the containers. Contamined clothing should be changed before entering eating areas. Do not eat or drink while working. See also section 8 for recommended protective equipment. Conditions for safe storage, including any incompatibilities Storage temperature:N.A. Incompatible materials: None in particular. Instructions as regards storage premises: Adequately ventilated premises. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Control parameters Appropriate engineering controls:N.A. Individual protection measures Eye protection: Use close fitting safety goggles, don't use eye lens. Protection for skin: Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton. Protection for hands: Use protective gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber. Respiratory protection: Use adequate protective respiratory equipment. No data available 9. PHYSICAL AND CHEMICAL PROPERTIES Information on basic physical and chemical properties Physical StateLiquid Appearance and colour:clear Odour:Mild Page n. of3 87/28/2023 Production Name HP 8200 Series B-SideDate Odour threshold:N.A. pH:N.A. Melting point / freezing point:N.A. Initial boiling point and boiling range:N.A. Flash point:N.A. Evaporation rate:N.A. Upper/lower flammability or explosive limits:N.A. Vapour density:>1
Vapour pressure:N.A.
Relative density:8.80 lbm/gal
Solubility in water:Soluble
Solubility in oil:N.A.
Partition coefficient (n-octanol/water):N.A.
Auto-ignition temperature:N.A.
Decomposition temperature: N.A.
Viscosity:750.00 cPo
Explosive properties:N.A.
Oxidizing properties:N.A.
Solid/gas flammability:N.A.
Other information
Substance Groups relevant propertiesN.A.
Miscibility:N.A.
Fat Solubility:N.A.
Conductivity:N.A.
10. STABILITY AND REACTIVITY
Reactivity
Stable under normal conditions
Chemical stability
Data not available.
Possibility of hazardous reactions
None.
Conditions to avoid
Stable under normal conditions.
Incompatible materials
None in particular.
Hazardous decomposition products
None.
11. TOXICOLOGICAL INFORMATION
Information on toxicological effects
Toxicological Information of the Preparation
a) acute toxicity Not classified
Based on available data, the classification criteria are not met
b) skin corrosion/irritation Not classified
Based on available data, the classification criteria are not met
c) serious eye damage/irritation Not classified
Based on available data, the classification criteria are not met
d) respiratory or skin sensitisationThe product is classified: Skin Sensitization, Category 1(H317)
e) germ cell mutagenicity Not classified
Based on available data, the classification criteria are not met
f) carcinogenicity Not classified
Based on available data, the classification criteria are not met
g) reproductive toxicity Not classified
Based on available data, the classification criteria are not met
h) STOT-single exposure The product is classified: Specific target organ toxicity following single exposure,
Category 1(H370)
i) STOT-repeated exposure The product is classified: Specific target organ toxicity following repeated exposure,
Category 2(H373)
Page n. of4 87/28/2023 Production Name HP 8200 Series B-SideDate

j) aspiration hazard Not classified
Based on available data, the classification criteria are not met
Toxicological information on main components of the mixture:
ETHOXYLATED, PROPOXYLATED ETHYLENEDIAMINE
CAS: 26316-40-5 a) acute toxicity LD50 Oral Rat > 5000 mg/kg
LD50 Skin Rabbit > 5000 mg/kg
b) skin corrosion/irritationSkin Irritant Rabbit No 4h
c) serious eye
damage/irritation
Eye Irritant Rabbit Yes
e) germ cell mutagenicityMutagenesis Salmonella Typhimurium Negative
Substance(s) listed on the IARC Monographs:
None
Substance(s) listed as OSHA Carcinogen(s):
None
Substance(s) listed as NIOSH Carcinogen(s):
None
Substance(s) listed on the NTP report on Carcinogens:
None
12. ECOLOGICAL INFORMATION
Toxicity
Adopt good working practices, so that the product is not released into the environment.
Eco-Toxicological Information:
Persistence and degradability
Bioaccumulative potential
Mobility in soil
Other adverse effects
N.A.
List of Eco-Toxicological properties of the product
Not classified for environmental hazards.
No data available for the product
List of Eco-Toxicological properties of the components
ETHOXYLATED, PROPOXYLATED ETHYLENEDIAMINE
CAS: 26316-40-5 a) Aquatic acute toxicity: LC50 Fish Pimephales promelas (fathead minnow) = 25600 mg/L 96h
a) Aquatic acute toxicity: EC50 Daphnia Daphnia magna (water flea) = 103 mg/L 48h
a) Aquatic acute toxicity: EC50 Desmodesmus subspicatus (green algae) > 100 mg/L 72h
METHYL FORMATE
CAS: 107-31-3 a) Aquatic acute toxicity: LC50 Fish Leuciscus idus = 120 mg/L 96h
a) Aquatic acute toxicity: EC50 Daphnia Daphnia magna (Water flea) > 500 mg/L 48h
ETHOXYLATED, PROPOXYLATED ETHYLENEDIAMINE
CAS: 26316-40-5 Non-readily biodegradable Test: Oxygen consumption; Value: 2.000
Notes: Exposure time 28 d
N.A.
N.A.
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Recover, if possible. Send to authorised disposal plants or for incineration under controlled conditions. In so doing, comply with the local and
national regulations currently in force.
14. TRANSPORT INFORMATION
Not classified as dangerous in the meaning of transport regulations.
Page n. of5 87/28/2023 Production Name HP 8200 Series B-SideDate

Not classified as dangerous in the meaning of transport regulations.
UN number
ADR-UN number: N.A.
DOT-UN Number: N.A.
IATA-Un number: N.A.
IMDG-Un number: N.A.
UN proper shipping name
ADR-Shipping Name: N.A.
DOT Proper Shipping Name: N.A.
IATA-Technical name:N.A.
IMDG-Technical name: N.A.
Transport hazard class(es)
ADR-Class:N.A.
DOT Hazard Class:N.A.
IATA-Class:N.A.
IMDG-Class:N.A.
Packing group
ADR-Packing Group: N.A.
DOT Packing Group:N.A.
IATA-Packing group:N.A.
IMDG-Packing group: N.A.
Environmental hazards
Marine pollutant:No
Environmental Pollutant:N.A.
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N.A.
Special precautions
Department of Transportation (DOT):
N.A.
Road and Rail (ADR-RID):
N.A.
Air (IATA):
N.A.
Sea (IMDG):
N.A.
15. REGULATORY INFORMATION
USA – Federal regulations
TSCA – Toxic Substances Control Act
SARA – Superfund Amendments and Reauthorization Act
CERCLA – Comprehensive Environmental Response, Compensation, and Liability Act
CAA – Clean Air Act
TSCA inventory:
No substances listed
TSCA listed substances:
No substances listed
Section 302 – Extremely Hazardous Substances:
No substances listed
Section 304 – Hazardous substances:
No substances listed
Section 313 – Toxic chemical list:
No substances listed
Substance(s) listed under CERCLA:
No substances listed
CAA listed substances:
Page n. of6 87/28/2023 Production Name HP 8200 Series B-SideDate

CWA – Clean Water Act
USA – State specific regulations
California Proposition 65
Massachusetts Right to know
Pennsylvania Right to know
New Jersey Right to know
No substances listed
CWA listed substances:
No substances listed
Substance(s) listed under California Proposition 65:
No substances listed
Substance(s) listed under Massachusetts Right to know:
No substances listed
Substance(s) listed under Pennsylvania Right to know:
No substances listed
Substance(s) listed under New Jersey Right to know:
No substances listed
16. OTHER INFORMATION
Safety Data Sheet dated: 7/28/2023 – version 6
The information contained herein is based on our state of knowledge at the above-specified date. It refers solely to the product indicated and
constitutes no guarantee of particular quality. The information relates only to the specific material and may not be valid for such material
used in combination with any other material or in any process.
This document was prepared by a competent person who has received appropriate training.
It is the duty of the user to ensure that this information is appropriate and complete with respect to the specific use intended.
This MSDS cancels and replaces any preceding release.
Legend to abbreviations and acronyms used in the safety data sheet:
ADR:European Agreement concerning the International Carriage of Dangerous Goods by Road.
RID:Regulation Concerning the International Transport of Dangerous Goods by Rail.
IMDG:International Maritime Code for Dangerous Goods.
IATA:International Air Transport Association.
Code Description
H224 Extremely flammable liquid and vapour.
H301 Toxic if swallowed.
H302 Harmful if swallowed.
H311 Toxic in contact with skin.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H331 Toxic if inhaled.
H335 May cause respiratory irritation.
H370 Causes damage to organs.
H373 May cause damage to organs through prolonged or repeated exposure.
Code Hazard class and hazard category Description
A.1/3/Dermal Acute Tox. 3 Acute toxicity (dermal), Category 3
A.1/3/Inhal Acute Tox. 3 Acute toxicity (inhalation), Category 3
A.1/3/Oral Acute Tox. 3 Acute toxicity (oral), Category 3
A.1/4/Oral Acute Tox. 4 Acute toxicity (oral), Category 4
A.3/2A Eye Irrit. 2A Eye irritation, Category 2A
A.4.2/1 Skin Sens. 1 Skin Sensitization, Category 1
A.8/1 STOT SE 1 Specific target organ toxicity following single exposure, Category 1
A.8/3 STOT SE 3 Specific target organ toxicity following single exposure, Category 3
A.9/2 STOT RE 2 Specific target organ toxicity following repeated exposure, Category 2
B.6/1 Flam. Liq. 1 Flammable Liquids Category 1
Page n. of7 87/28/2023 Production Name HP 8200 Series B-SideDate

IATA:International Air Transport Association.
IATA-DGR:Dangerous Goods Regulation by the “International Air Transport Association” (IATA).
ICAO:International Civil Aviation Organization.
ICAO-TI:Technical Instructions by the “International Civil Aviation Organization” (ICAO).
GHS:Globally Harmonized System of Classification and Labeling of Chemicals.
CLP:Classification, Labeling, Packaging.
EINECS:European Inventory of Existing Commercial Chemical Substances.
INCI:International Nomenclature of Cosmetic Ingredients.
CAS:Chemical Abstracts Service (division of the American Chemical Society).
GefStoffVO:Ordinance on Hazardous Substances, Germany.
LC50:Lethal concentration, for 50 percent of test population.
LD50:Lethal dose, for 50 percent of test population.
DNEL:Derived No Effect Level.
PNEC:Predicted No Effect Concentration.
TLV:Threshold Limiting Value.
TWATLV:Threshold Limit Value for the Time Weighted Average 8 hour day. (ACGIH Standard).
STEL:Short Term Exposure limit.
STOT:Specific Target Organ Toxicity.
WGK:German Water Hazard Class.
KSt:Explosion coefficient.
The information in this SDS is provided all the relevant data fully and truly. However, the information is provided without any
warranty on their absolute extensiveness and accuracy. This SDS was prepared to provide safety preventive measures for the users
who have got professional training. The personal user who obtained this SDS should make independent judgment for the
applicability of this SDS under special conditions. In these special cases, we do not assume responsibility for the damage.
Page n. of8 87/28/2023 Production Name HP 8200 Series B-SideDate

25HP8204AF_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8200 SERIES A-SIDE
Safety Data Sheet dated: 7/28/2023 – version 5
Date of first edition: 4/13/2023
1. IDENTIFICATION
Product identifier
Mixture identification:
Trade name:HP 8200 SERIES A-SIDE
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use:N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company:ETECO INC.
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable:N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION
Classification of the chemical
Label elements
Skin irritation, Category 2 Causes skin irritation.
Eye irritation, Category 2A Causes serious eye irritation.
Respiratory Sensitization, Category 1 May cause allergy or asthma symptoms or breathing difficulties if
inhaled.
Skin Sensitization, Category 1 May cause an allergic skin reaction.
Carcinogenicity, Category 2 Suspected of causing cancer.
Specific target organ toxicity following single exposure,
Category 3
May cause respiratory irritation.
Specific target organ toxicity following repeated exposure,
Category 2
May cause damage to organs through prolonged or repeated
exposure.
Acute toxicity (inhalation), Category 4 Harmful if inhaled.
Hazard pictograms and Signal Word
Danger
Hazard statements
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
Page n. of1 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

Hazards not otherwise classified identified during the classification process:
None
Additional classification information
HMIS Health:3 = SERIOUS
HMIS Flammability:0 = Not Combustible
HMIS Reactivity:0 = MINIMAL
HMIS P.P.E.:Safety glasses, gloves
NFPA Health:3 = SERIOUS
NFPA Flammability:0 = Not Combustible
NFPA Reactivity:0 = MINIMAL
NFPA Special Risk:NONE
H373 May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash … Thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing must not be allowed out of the workplace.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P302+P352 IF ON SKIN: Wash with plenty of water/
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P304+P341 IF INHALED: If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable
for breathing.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy
to do. Continue rinsing.
P308+P313 IF exposed or concerned: Get medical advice/attention.
P312 Call a POISON CENTER/doctor/ if you feel unwell.
P314 Get medical advice/attention if you feel unwell.
P321 Specific treatment (see … On this label).
P332+P313 If skin irritation occurs: Get medical advice/attention.
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
P342+P311 If experiencing respiratory symptoms: Call a POISON CENTER/doctor/
P362+P364 Take off contaminated clothing and wash it before reuse.
P363 Wash contaminated clothing before reuse.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents/container to …
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
N.A.
Mixtures
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification:
List of components
Qty Name Ident. Numb. Classification Registration Number
60-80 % DIPHENYLMETHANEDIISOCYANATE CAS:9016-87-9 Skin Irrit. 2, H315; Eye Irrit. 2A,
H319; STOT SE 3, H335; STOT RE
Page n. of2 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

60-80 % DIPHENYLMETHANEDIISOCYANATE CAS:9016-87-9
H319; STOT SE 3, H335; STOT RE
2, H373; Resp. Sens. 1, H334
30-70 % 4,4′-METHYLENEDIPHENYL
DIISOCYANATE
CAS:101-68-8 Acute Tox. 4, H332; Skin Irrit. 2,
H315; Eye Irrit. 2A, H319; Carc. 2,
H351; STOT SE 3, H335; STOT RE
2, H373; Resp. Sens. 1, H334;
Skin Sens. 1, H317
The actual concentration of the components listed above is withheld as a trade secret.
4. FIRST AID MEASURES
Description of first aid measures
In case of skin contact:
Immediately take off all contaminated clothing.
Remove contaminated clothing immediatley and dispose off safely.
After contact with skin, wash immediately with soap and plenty of water.
In case of eyes contact:
After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an opthalmologist
immediately.
Protect uninjured eye.
In case of Ingestion:
Do not induce vomiting, get medical attention showing the SDS and label hazardous.
In case of Inhalation:
If breathing is irregular or stopped, administer artificial respiration.
In case of inhalation, consult a doctor immediately and show him packing or label.
Most important symptoms/effects, acute and delayed
Eye irritation
Eye damages
Skin Irritation
Erythema
Indication of any immediate medical attention and special treatment needed
In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).
5. FIRE-FIGHTING MEASURES
Extinguishing media
Suitable extinguishing media:
Water.
Carbon dioxide (CO2).
Unsuitable extinguishing media:
None in particular.
Specific hazards arising from the chemical
Do not inhale explosion and combustion gases.
Burning produces heavy smoke.
Hazardous combustion products:N.A.
Explosive properties:N.A.
Oxidizing properties:N.A.
Special protective equipment and precautions for fire-fighters
Use suitable breathing apparatus .
Collect contaminated fire extinguishing water separately. This must not be discharged into drains.
Move undamaged containers from immediate hazard area if it can be done safely.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Wear personal protection equipment.
Wear breathing apparatus if exposed to vapours/dusts/aerosols.
Provide adequate ventilation.
Use appropriate respiratory protection.
See protective measures under point 7 and 8.
Methods and material for containment and cleaning up
Suitable material for taking up: absorbing material, organic, sand
Wash with plenty of water.
Page n. of3 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

7. HANDLING AND STORAGE
Precautions for safe handling
Avoid contact with skin and eyes, inhaltion of vapours and mists.
Exercise the greatest care when handling or opening the container.
Do not use on extensive surface areas in premises where there are occupants.
Use localized ventilation system.
Don’t use empty container before they have been cleaned.
Before making transfer operations, assure that there aren’t any incompatible material residuals in the containers.
Contamined clothing should be changed before entering eating areas.
Do not eat or drink while working.
See also section 8 for recommended protective equipment.
Conditions for safe storage, including any incompatibilities
Storage temperature:N.A.
Always keep in a well ventilated place.
Incompatible materials:
None in particular.
Instructions as regards storage premises:
Cool and adequately ventilated.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Appropriate engineering controls:N.A.
Individual protection measures
Eye protection:
Use close fitting safety goggles, don’t use eye lens.
Protection for skin:
Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton.
Protection for hands:
Use protective gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber.
Respiratory protection:
Use adequate protective respiratory equipment.
No data available
9. PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Physical StateLiquid
Appearance and colour:brown
Odour:Slightly Musty
Odour threshold:N.A.
pH:N.A.
Melting point / freezing point:N.A.
Initial boiling point and boiling range:300 C (572 F)
Flash point:N.A.
Evaporation rate:N.A.
Upper/lower flammability or explosive limits:N.A.
Vapour density:8.5
Vapour pressure:0.000004 mmHg @ 25 C
Relative density:9.00 lbm/gal
Solubility in water:N.A.
Solubility in oil:N.A.
Partition coefficient (n-octanol/water):N.A.
Auto-ignition temperature:N.A.Notes:>600 C
Decomposition temperature: N.A.
Viscosity:1,100.00 cPo
Explosive properties:N.A.
Oxidizing properties:N.A.
Solid/gas flammability:N.A.
Other information
Substance Groups relevant propertiesN.A.
Miscibility:N.A.
Fat Solubility:N.A.
Page n. of4 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

Fat Solubility:N.A.
Conductivity:N.A.
10. STABILITY AND REACTIVITY
Reactivity
Stable under normal conditions
Chemical stability
Data not available.
Possibility of hazardous reactions
None.
Conditions to avoid
Stable under normal conditions.
Incompatible materials
None in particular.
Hazardous decomposition products
None.
11. TOXICOLOGICAL INFORMATION
Information on toxicological effects
Toxicological Information of the Preparation
a) acute toxicity The product is classified: Acute toxicity (inhalation), Category 4(H332)
b) skin corrosion/irritation The product is classified: Skin irritation, Category 2(H315)
c) serious eye damage/irritation The product is classified: Eye irritation, Category 2A(H319)
d) respiratory or skin sensitisationThe product is classified: Respiratory Sensitization, Category 1(H334), Skin
Sensitization, Category 1(H317)
e) germ cell mutagenicity Not classified
Based on available data, the classification criteria are not met
f) carcinogenicity The product is classified: Carcinogenicity, Category 2(H351)
g) reproductive toxicity Not classified
Based on available data, the classification criteria are not met
h) STOT-single exposure The product is classified: Specific target organ toxicity following single exposure,
Category 3(H335)
i) STOT-repeated exposure The product is classified: Specific target organ toxicity following repeated exposure,
Category 2(H373)
j) aspiration hazard Not classified
Based on available data, the classification criteria are not met
Substance(s) listed on the IARC Monographs:
None
Substance(s) listed as OSHA Carcinogen(s):
None
Substance(s) listed as NIOSH Carcinogen(s):
None
Substance(s) listed on the NTP report on Carcinogens:
None
12. ECOLOGICAL INFORMATION
Toxicity
Adopt good working practices, so that the product is not released into the environment.
Eco-Toxicological Information:
Persistence and degradability
Bioaccumulative potential
List of Eco-Toxicological properties of the product
Not classified for environmental hazards.
No data available for the product
N.A.
Page n. of5 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

Bioaccumulative potential
Mobility in soil
Other adverse effects
N.A.
N.A.
N.A.
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Recover, if possible. Send to authorised disposal plants or for incineration under controlled conditions. In so doing, comply with the local and
national regulations currently in force.
14. TRANSPORT INFORMATION
UN number
ADR-UN number: 3082
DOT-UN Number: UN3082
IATA-Un number: 3082
IMDG-Un number: 3082
UN proper shipping name
ADR-Shipping Name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
DOT Proper Shipping Name: Environmentally hazardous substance, liquid, n.o.s.
IATA-Technical name:ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
IMDG-Technical name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
Transport hazard class(es)
ADR-Class:9
DOT Hazard Class:9
IATA-Class:9
IMDG-Class:9
Packing group
ADR-Packing Group: III
DOT Packing Group:III
IATA-Packing group:III
IMDG-Packing group: III
Environmental hazards
Marine pollutant:No
Environmental Pollutant:N.A.
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N.A.
Special precautions
Department of Transportation (DOT):
DOT-Special Provision(s):8, 146, 173, 335, IB3, T4, TP1, TP29
DOT Label(s):9
DOT Symbol:N/A
DOT Cargo Aircraft:No limit
DOT Passenger Aircraft:No limit
DOT Bulk:241
DOT Non-Bulk:203
Road and Rail (ADR-RID):
ADR-Label:9
ADR – Hazard identification number:90
ADR-Transport category (Tunnel restriction code):3 (-)
Air (IATA):
IATA-Passenger Aircraft:964
IATA-Cargo Aircraft:964
IATA-Label:9
IATA-Subrisk:-
IATA-Erg:9L
IATA-Special Provisions:A97 A158 A197 A215
Page n. of6 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

IATA-Special Provisions:A97 A158 A197 A215
Sea (IMDG):
IMDG-Stowage Code: Category A
IMDG-Stowage Note: –
IMDG-Subrisk:-
IMDG-Special Provisions:274 335 969
IMDG-EMS: F-A, S-F
15. REGULATORY INFORMATION
USA – Federal regulations
TSCA – Toxic Substances Control Act
SARA – Superfund Amendments and Reauthorization Act
CERCLA – Comprehensive Environmental Response, Compensation, and Liability Act
CAA – Clean Air Act
CWA – Clean Water Act
USA – State specific regulations
California Proposition 65
Massachusetts Right to know
Pennsylvania Right to know
New Jersey Right to know
TSCA inventory:
No substances listed
TSCA listed substances:
No substances listed
Section 302 – Extremely Hazardous Substances:
No substances listed
Section 304 – Hazardous substances:
No substances listed
Section 313 – Toxic chemical list:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under CERCLA:
No substances listed
CAA listed substances:
No substances listed
CWA listed substances:
No substances listed
Substance(s) listed under California Proposition 65:
No substances listed
Substance(s) listed under Massachusetts Right to know:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under Pennsylvania Right to know:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under New Jersey Right to know:
No substances listed
16. OTHER INFORMATION
Code Description
Page n. of7 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

Safety Data Sheet dated: 7/28/2023 – version 5
The information contained herein is based on our state of knowledge at the above-specified date. It refers solely to the product indicated and
constitutes no guarantee of particular quality. The information relates only to the specific material and may not be valid for such material
used in combination with any other material or in any process.
This document was prepared by a competent person who has received appropriate training.
It is the duty of the user to ensure that this information is appropriate and complete with respect to the specific use intended.
This MSDS cancels and replaces any preceding release.
Legend to abbreviations and acronyms used in the safety data sheet:
ADR:European Agreement concerning the International Carriage of Dangerous Goods by Road.
RID:Regulation Concerning the International Transport of Dangerous Goods by Rail.
IMDG:International Maritime Code for Dangerous Goods.
IATA:International Air Transport Association.
IATA-DGR:Dangerous Goods Regulation by the “International Air Transport Association” (IATA).
ICAO:International Civil Aviation Organization.
ICAO-TI:Technical Instructions by the “International Civil Aviation Organization” (ICAO).
GHS:Globally Harmonized System of Classification and Labeling of Chemicals.
CLP:Classification, Labeling, Packaging.
EINECS:European Inventory of Existing Commercial Chemical Substances.
INCI:International Nomenclature of Cosmetic Ingredients.
CAS:Chemical Abstracts Service (division of the American Chemical Society).
GefStoffVO:Ordinance on Hazardous Substances, Germany.
LC50:Lethal concentration, for 50 percent of test population.
LD50:Lethal dose, for 50 percent of test population.
DNEL:Derived No Effect Level.
PNEC:Predicted No Effect Concentration.
TLV:Threshold Limiting Value.
TWATLV:Threshold Limit Value for the Time Weighted Average 8 hour day. (ACGIH Standard).
STEL:Short Term Exposure limit.
STOT:Specific Target Organ Toxicity.
WGK:German Water Hazard Class.
KSt:Explosion coefficient.
The information in this SDS is provided all the relevant data fully and truly. However, the information is provided without any
warranty on their absolute extensiveness and accuracy. This SDS was prepared to provide safety preventive measures for the users
who have got professional training. The personal user who obtained this SDS should make independent judgment for the
applicability of this SDS under special conditions. In these special cases, we do not assume responsibility for the damage.
Paragraphs modified from the previous revision:
– 9. PHYSICAL AND CHEMICAL PROPERTIES
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
H373 May cause damage to organs through prolonged or repeated exposure.
Code Hazard class and hazard category Description
A.1/4/Inhal Acute Tox. 4 Acute toxicity (inhalation), Category 4
A.2/2 Skin Irrit. 2 Skin irritation, Category 2
A.3/2A Eye Irrit. 2A Eye irritation, Category 2A
A.4.1/1 Resp. Sens. 1 Respiratory Sensitization, Category 1
A.4.2/1 Skin Sens. 1 Skin Sensitization, Category 1
A.6/2 Carc. 2 Carcinogenicity, Category 2
A.8/3 STOT SE 3 Specific target organ toxicity following single exposure, Category 3
A.9/2 STOT RE 2 Specific target organ toxicity following repeated exposure, Category 2
Page n. of8 87/28/2023 Production Name HP 8200 SERIES A-SIDEDate

25HP8203A-D_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8200 SERIES A-SIDE ~
Safety Data Sheet dated: 7/28/2023 – version 5
Date of first edition: 4/13/2023 INC
POLYURETHANE SPECIALIST
1, IDENTIFICATION
Product identifier
Mixture identification:
Trade name: HP 8200 SERIES A-SIDE
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use: N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company: ETECO INC,
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable: N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300 *
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S, Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION .
Classification of the chemical
Skin irritation, Category 2 Causes skin irritation.
Eye irritation, Category 2A Causes serious eye irritation. .
Respiratory Sensitization, Category 1 May cause allergy or asthma symptoms or breathing difficulties if
inhaled,
Skin Sensitization, Category 1 May cause an allergic skin reaction.
Carcinogenicity, Category 2 Suspected of causing cancer.
Specific target organ toxicity following single exposure, May cause respiratory irritation.
Category 3
Specific target organ toxicity following repeated exposure, May cause damage to organs through prolonged or repeated
Category 2 exposure.
Acute toxicity (inhalation), Category 4 Harmful if inhaled.
Label elements
Hazard pictograms and Signal Word
Danger
Hazard statements
HB15 Causes skin irritation.
#317 May cause an allergic skin reaction,
#319 Causes serious eye irritation,
4332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
Date 7/28/2023 Production Name HP 8200 SERIES A-SIDE Pagen. 1 of 8

25HP8202-D_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8200 SERIES A-SIDE
Safety Data Sheet dated: 7/28/2023 – version 5
Date of first edition: 4/13/2023 E T E Cc O Inc.
POLYURETHANE SPECIALIST
1, IDENTIFICATION
Product identifier
Mixture identification:
Trade name: HP 8200 SERIES A-SIDE

Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use: N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company: ETECO INC.

1000 S. Linwood Ave.

Santa Ana, CA 92705

Company Phone: + 001 714-480-1370
Responsable: N.A.
Emergency telephone number .
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION .
Classification of the chemical
Skin irritation, Category 2 Causes skin irritation.
Eye irritation, Category 2A Causes serious eye irritation.
Respiratory Sensitization, Category 1 May a allergy or asthma symptoms or breathing difficulties if

inhaled.

Skin Sensitization, Category 1 May cause an allergic skin reaction.
Carcinogenicity, Category 2 Suspected of causing cancer.
Specific target organ toxicity following single exposure, May cause respiratory irritation.
Category 3
Specific target organ toxicity following repeated exposure, May cause damage to organs through prolonged or repeated
Category 2 exposure.
Acute toxicity (inhalation), Category 4 Harmful if inhaled.
Label elements
Hazard pictograms and Signal Word
&o
Hazard statements
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
1335 May cause respiratory irritation.
H351 Suspected of causing cancer.
Date 7/28/2023 Production Name HP 8200 SERIES A-SIDE Pagen. 1- of 8

25HP8203-D_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8200 SERIES A-SIDE
Safety Data Sheet dated: 7/28/2023 – version 5
Date of first edition: 4/13/2023 E T E Cc O Inc.
POLYURETHANE SPECIALIST
1, IDENTIFICATION
Product identifier
Mixture identification:
Trade name: HP 8200 SERIES A-SIDE

Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use: N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company: ETECO INC.

1000 S. Linwood Ave.

Santa Ana, CA 92705

Company Phone: + 001 714-480-1370
Responsable: N.A.
Emergency telephone number .
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION .
Classification of the chemical
Skin irritation, Category 2 Causes skin irritation.
Eye irritation, Category 2A Causes serious eye irritation.
Respiratory Sensitization, Category 1 May a allergy or asthma symptoms or breathing difficulties if

inhaled.

Skin Sensitization, Category 1 May cause an allergic skin reaction.
Carcinogenicity, Category 2 Suspected of causing cancer.
Specific target organ toxicity following single exposure, May cause respiratory irritation.
Category 3
Specific target organ toxicity following repeated exposure, May cause damage to organs through prolonged or repeated
Category 2 exposure.
Acute toxicity (inhalation), Category 4 Harmful if inhaled.
Label elements
Hazard pictograms and Signal Word
&o
Hazard statements
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
1335 May cause respiratory irritation.
H351 Suspected of causing cancer.
Date 7/28/2023 Production Name HP 8200 SERIES A-SIDE Pagen. 1- of 8

25HP8105BF_SDS.pdf

by | Sep 27, 2025

1
SAFETY DATA SHEET
PRODUCT NAME: HP 81 05 B
MSDS NUMBER: HP 8105 B
DATE: June 0’1,2021
SUPERSEDES MSDS: June 01,2018
SECTION 1: MATERIAL AND MANUFACTURER IDENTIFICATION
MANUFACTURER: TRANSPORTATION EMERGENCY CALL CHEMTREC
Eteco, lnc. 800 424 9300
1000 South Linwood Ave. MEDICAL EMERGENCY INFORMATION:
Santa Ana, CA92705 800 328 8501
Phone: 714 480 1370
PRODUCTION IDENTIFICATION NUMBER: HP 8’105 B
CHEMICAL FAMILY: POLYETHER POLYOL BLEND
SECTION 2: HAZARDS IDENTIFICATION
This material is classified as hazardous under OSHA Hazard Communication Standard (29 CFR 1910.1200).
PhysicalState: Liquid
Potential Acute Heath Effects:
Eyes Corrosive to eyes.
Skin Corrosive to skin on contact. Skin contact may produce burns.
lnhalation lnhalation of the spray mist may produce severe irritation of respiratory tract, characterized by
coughing, choking or shortness of breath.
lngestion May cause burns to mouth, throat and stomach.
GENERAL INFORMATION: Read the entire MSDS for more thorough evaluation of the hazards.
GHS Label Elements:
Hazard pictograms
SignalWord:
Hazard statement:
Precautionary statements:
Warning
Causes serious eye irritation
Wear eye protection, protective clothing, protective gloves. lf in eyes: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and
easy to do. Continue rinsing. lf eye irritation persists: Get medical
advice/attention.
t
a

2
SECTION 3: COMPOSITION AND INFORMATION ON INGREDIENTS
MATERIAL OR COMPONENT
PROPRIETARY COMPONENT
GLYCOLS
CAS
NUMBER
Mixture
Mixture
%BY
WEIGHT
55-90 %
0-10 %
*Occupational
Exposure Limit(s), if available, are listed in Section B
SECTION 4: FIRST AID MEASURES
Eye Contact: Check for and remove any contact lenses. ln case of eye contact, immediately flush eyes with
plenty of water for at least 15 minutes. Get immediate medical attention.
Skin Contact: ln case of contact, immediately wash skin with soap and plenty of water for at least
’15
minutes
while removing contaminated clothing and shoes. Wash clothing before reuse. Get medical attention
immediately.
lnhalation: lf excessive inhalation of vapor occurs, remove to fresh air. lf breathing is difficult, qualified
personnel may administer oxygen. Get medical attention immediately.
lngestion: Do NOT induce vomiting unless directed to do so by medical personnel. Never give anything by
mouth to an unconscious person. lf large quantities of this material are swallowed, call a physician
immediately. Loosen tight clothing such as a collar, tie, belt or waistband.
Notes to Physician: Symptomatic treatment and supportive therapy as indicated. Administer oxygen if
necessary.
Following severe exposure the patient should be kept under medical review for at least 48 hours as
delayed pulmonary edema may develop.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: >212’F Closed Cup
Auto lgnition Temp: Not available
Flammable Limits: Not available
Products of Combustion:
Thermal Decomposition products are toxic and may include oxides of carbon and nitrogen,
amines, possibly other irritating gases.
Fire Fighting Media and Instructions:
SMALL FIRE: Use DRY chemical powder.
LARGE FIRE: Use water spray, fog or foam. Do not use water jet.
Protective Clothing (Fire):
Splash goggles. Full suit. Boots. Gloves. A self-contained breathing apparatus should be used to
avoid inhalation of the product.

J
SECTION 6: ACCIDENTAL RELEASE MEASURES
For major spills call Chemtrec (800-424-9300l-
See Safety Data Sheet section 8 Personal Protective Equipment
Small Spill and Leak Absorb with an inert material and put the material in an appropriate waste disposal container
Large Spill and Leak Corrosive liquid. Toxic liquid.
Stop leak if without risk. Absorb with DRY earth, sand or other non-combustible material. Do not get water
inside container. Do not touch spilled material. Use water spray curtain to divert vapor drift. Use water
spray to reduce vapors. Prevent entry into sewers, basements of confined area; dike if needed. Eliminate
all ignition sources. Call for assistance on disposal. Finish cleaning by spreading water on the
contaminated surface and allow to evacuate through the sanitary system. Be careful that the product is
not present at a concentration level above TLV. Check TLV on the MSDS and with local authorities.
SECTION 7: HANDLING AND STORAGE
Handling Do not ingest. Do not breathe vapor or mist. Keep container closed. Use only with adequate ventilation
Wash thoroughly after handling. Avoid contactwith eyes, skin and clothing.
Storage Keep container tightly closed. Keep container in a cool, well-ventilated area
SECTION 8: EXPOSURE CONTROLS AND PERSONAL PROTEGTION
Preventive Measures Conditions of use, adequacy of engineering or other control measures, and actual exposures will
dictate the need for specific protective devices at your workplace.
Engineering Controls Use local exhaust ventilation to maintain airborne concentrations bellow the TLV. Suitable
respiratory equipment should be used in case of insufficient ventilation or where operational procedures
demand it. For guidance on engineering control measures refer to publications such as the ACGIH
current edition of ‘lndustrial Ventilation, a manual of Recommended Practice.’
Personal Protection
Eyes Chemical safety goggles. lf there is a potential for splashing, use a full-face shield.
Body and Hands Full chemical suit. Gloves
Respiratory Wear appropriate respirator when ventilation is inadequate
Personal Protection in case of a Large Spill
Splash goggles. Full suit. Vapor respirator or a self-contained breathing apparatus. Boots.
Gloves.
Suggested protective clothing might not be sufficient; consult a specialist BEFORE handling this product.
Product Name Exposure Limits

4
SECTION 9: PHYSICAL AHD CHEMICAL PROPERTIES
APPEARANCE AND ODOR
BOtLING POTNT (.F/.C)
MELTTNG POTNT (.F/.C)
SPECIFIC GRAVITY (WATER = 1)
BULK DENSITY
pH OF UNDILUTED PRODUGT
VAPOR PRESSURE (MM Hg.)
VAPOR DENSTTY (ArR-1)
VISCOSITY
PERCENT (%) VOC
SOLUBILITY IN WATER
Clear Slight Odor
Not determined
Not determined
1.12 kgll
8.8|b/gal
Not determined
Not determined
>1
600 to 900 cps @25″ C
0
Soluble
SECTION 10: STABILITY AND REACTIVITY
Stability and Reactivity
Conditions of Sta bility
This product is stable.
Avoid moisture to protect product quality
Incompatibility with Various Substances
Slightly reactive to reactive with oxidizing agents, alkalis.
Hazardous Decomposition Products
Thermal decomposition products are toxic and may include oxides of carbon and
nitrogen, amines, possibly other irritating gases.
Hazardous Polymerization Will not occur
SECTION 1 1 : TOXICOLOGIcAL INFORMATION
No applicable data for this section
SEGTION 121: ECOLOGICAL INFORMATION
No applicable data for this section
SECTION 13: DISPOSAL CONSIDERATIONS
Waste lnformation lncinerate or landfill in a licensed facility. Do not discharge into watenryays of sewer systems.
Container Disposal: Steeldrums must be emptied (as defined by RCRA, Section 261.7 orstate
regulations that may be more stringent) and can be sent to a licensed drum reconditoiner for reuse, a
scrap metal dealer or an approve landfill. Drums destined for scrap dealer of landfill must be punctured or
crushed to prevent reuse.
Material for disposal should be placed in appropriated sealed containers to avoid potential human and
environmental exposure. lt is the responsibility of the generator to comply with all federal, state,
provincial and local laws and regulations. We recommend that you contact an appropriate waste disposal
contractor and environmental agency for relevant laws and regulations. Under the US, Resource
Conservation and Recovery Act (RCRA), it is the responsibility of the user of the product to determined at
the time of disposal, whether the product meets relevant waste classification and to assure proper
disposal.

5
SECTION 14: TRANSPORT INFORMATION
Tra ns portati on Emerge ncy N um b er 1 -800 424-9 300 (C H E MTREC).
DOT Classification
TDG Classification
I MO/IMDG Classification
I CAO/IATA Classification
Non Regulated
Non Regulated
Non Regulated
Non Regulated
SECTION 15: REGULATORY INFORMATION
U.S. Federal Regulations
This material is classified as hazardous under OSHA Hazard Communication Standard (29 CFR 1910,1200).
HCS C/assification
Class: Corrosive material
TSCA 8(b) inventory: All ingredients Listed.
CERGLA (Comprehensive Environmental Response, Compensation and Liability Act):
Any spill or release above the RC must be reported to the National Response Center (800-424-8802)
SARA 313 toxic chemical notification and release reporting: None
Sfafe Regulations California prop 65: No ingredients listed.
Canadian Regulations
This product has been classified in accordance with the hazard criteria of the CPR
(Controlled Products Regulations) and this MSDS (Material Safety Data Sheet) contains all the
information required by the CPR.
WHMIS (Canada) Class D-1B: Material causing immediate and serious toxic effects (Toxic).
Class D-28: Material causing other toxic effects (Toxic).
CEPA DSL/NDSL Not all lngredients Listed.
SECTION 16: OTHER INFORMATION
Causes respiratory tract, eye and skin burns.
Harmful if inhaled.
May be harmful if swallowed.
Contains material, which may cause birth defects based on animal data
Hazardous Material lnformation System (U.S.A.) National Fire Protection Association (U.S.A.)
Health:
Fire Hazard
Reactivity:
“l
1
0
Health:
Fire Hazard
Reactivity:
1
1
0

6
Notice to Reader
White the information and recommendations in this publication are to the best of our knowledge, information and
belief accurate atthe date of pubtication, NOTHING HEREIN TS fO BE CONSIRUED AS A WARANTy, EXPRESS
OR OTHERWISE.
IN ALL CASES, IT IS THE RESPONS/BILITY OF THE USER TO DETERMINE THE APPLICABILITY OF SUCH
INFORMATION AND RECOMMENDATIONSAND THE SUITABILITY OF ANY PRIDUCT FOR
‘TS
OWN PARTICULAR
PURPOSE.
THE PRODUCT MAY PRESENT HAZARDS AND SHOULD BE USED WITH CAUTION. WHILE CERTAIN HAZAEDS
ARE DESCRIBED IN THIS PUBLICATION, NO GUARANTEE IS MADE THAT THESE ARE THE ONLY HAZARDS
THAT EXIST.
Hazards, toxicity, and behavior of the products may differ when used with other materials and are dependent
upon the manufacturing circumsfances or other processes. Such hazards, toxicity and behavior should be
determined by the user and made known to handlers, processors and end use/s.
We disclaim liability for damage or injury incurring directly or indirectly from the use of this product.
APPROVED AND AUTHORIZED BY: EnesTorlic

25HP8105AF_SDS.pdf

by | Sep 27, 2025

I
SAFETY DATA SHEET
PRODUCT NAME: HP 8105 A
MSDS NUMBER: HP 8105 A
DATE: June 21,2021
SUPERSEDES MSDS: June 21,2018
SECTION 1: MATERIAL AND MANUFACTURER IDENTIFIGATION
MANUFACTURER: TRANSPORTATION EMERGENCY CALL CHEMTREC
Eteco, lnc. 800 424 9300
1000 South Linwood Ave. MEDICAL EMERGENCY INFORMATION:
Santa Ana, CA92705 800 328 8501
Phone: 714 480 1370
PRODUCT IDENTIFICATION NUMBER: HP 8105 A
CHEMICAL FAMILY: POLYMERIC ISOCYANATE
SECTION 2: HAZARDS IDENTIFICATON
This materialis classified as hazardous under OSHA Hazard Communication Standard (29 CFR 1910.1200)
Physical State and Appearance: Brown Liquid
Emergency Overview:
INHALATION OF MDI MISTS OR VAPORS MAY CAUSE RESPIRATORY IRRITATION, BREATHLESSNESS, CHEST
DISCOUMFORT AND REDUCED PULMONARY FUNCTION. OVEREXPOSURE WELL ABOVE THE PEL MAY
RESULT IN BRONCHITIS, BRONCHIAL SPASMS AND PULMONARY EDEMA. LONG-TERM EXPOSURE TO
ISOCYANATES HAS BEEN REPORTED TO CAUSE LUNG DAMAGE, INCLUDING REDUCED LUNG FUNCTION
WHICH MAY BE PERMANENT. ACUTE OR CHRONIC OVEREXPOSURE TO ISOCYANATES MAY CAUSE
SENSATION IN SOME INDIVIDUALS, RESULTING IN ALLERGIC RESPRATORY REACTIONS INCLUDING
WHEEZING, SHORTNESS OF BREATH AND DIFFICULTY BREATHING.
Skin: HAZARDOUS lN CASE OF SKIN CONTACT (IRRITANT, SENSITIZER). SKIN INFLAMMATION lS
IS CHARACTERIZED BY ITCHING, SCALING OR REDDENING.
Eyes: HAZARDOUS lN CASE OF EYE CONTACT (IRRITANT).
lnhalation: HAZARDOUS lN CASE OF INHALATION (LUNG IRRITANT, LUNG SENSITIZER).
lngestion: SLIGHTLY HAZARDOUS lN CASE OF INGESTION.
Medical Conditions Aggravated by Overexposure: Preexisting conditions such as asthma, allergies, eczema,
bronchitis, and other lung and skin disorders may be aggravated by exposure to the product. Results from a lifetime
inhalation study in rats indicate that MDI aerosolwas carcinogenic at 9 mg/m3, the highest dose tested. This is well above
the recommended TLV of 5ppb (0.05 mg/m3). Only irritation was noted at the lower concentration of 0.2 and 1 mg/m3. No
birth defects orteratogenic effects were reported in a teratology study with rats exposed to 1,4, and 12mglm3 polymeric
MDI for 6 hr/day on days 6-15 of gestation. Embryotoxicity and fetotoxicity was reported at the top dose in the presence of
maternal toxicity. As a result of previous repeated overexposures or a single large dose, certain individuals will develop
isocyanate sensitization (chemical asthma), which will cause them to react to a later exposure to isocyanate at levels well
below the PEL/WL. Those symptoms, which include chest tightness, wheezing, cough, shortness of breath, or asthmatic
attack, could be immediate of delayed up to several hours after exposure. Similar to many non-specific asthmatic
responses, there are reports that once sensitized an individual can experience these symptoms upon exposure to dust,
cold air or other irritants. This increased lung sensitivity can persist for weeks and in severe cases for several years.
Chronic overexposure to isocyanates has also been reported to cause lung damage, including a decrease in lung
function, which may be permanent. Sensitization may e either temporary of permanent. Prolonged contact can cause
reddening, swelling, rash, scaling, or blistering, in those who have developed a skin sensitization, these symptoms can
develop as a result of contact with very small amount s of liquid material, or even as a result of vapor-only exposure.

2
Aggravated Medical Conditions:
tnOividuals who are sensitized to isocyanates and those with preexisting lung diseases of conditions, including non-
specific bronchial hyper reactivity or asthma, must avoid all exposure to isocyanates.
GHS Label Elements
@c
Hazard Pictograms
SignalWord:
Hazard statement
Danger
Harmful if inhaled. Causes skin and eye irritation.
May Cause allergy or asthma symptoms or breathing difficulties if inhaled
May cause an allergic skin reaction.
May cause respiratory irritation.
SECTION 3: HAZARDOUS INGREDIENTS
MATERIAL OR COMPONENT cAs
NUMBER
%BY
WEIGHT
POLYMERIC DIPHENYLMETHANE DIISOCYANATE 9O’16-87-9 IOOO/O
*Occupational
Exposure Limit(s) if available, are listed in section 8
SECTION 4: FIRST AID MEASURES
Eyes: ln case of eye contact, immediately flush eyes with large amounts of water for at least 15 minutes, keeping the
eyelids open. Get immediate medical attention.
Skin Contact: Remove contaminated clothing. ln case of contact, immediately wash skin with soap and plenty of water
lf symptoms develop obtain medicalattention. Contaminated clothing should be thoroughly cleaned. An MDI study has
demonstrated that a polyglycol-based skin cleaner or corn oil may be more effective than soap and water.
lnhalation: lf excessive inhalation of vapor occurs, remove patient to fresh air. lf not breathing, give artificial respiration,
preferably mouth-to-mouth. lf breathing is difficult, qualified personnel may administer oxygen. Get immediate medical
attention.
lngestion: lf swallowed, dilute with water. DO NOT INDUCE VOMITING. Never give fluids or induce vomiting if the victim
is unconscious or having convulsions. Get immediate medical attention.
NOTES TO PHYSICIANS: There is no specific antidote to counteract the effects of MDl. Symptomatic and supportive
therapy as needed. Following severe exposure medical follow-up should be monitored for at least 48 hours.
Other First Aid Procedures: Medical supervision of all employees who handle or come into contact with MDI is
recommended. Pre-employment and periodic medical examinations with respiratory function test (PEV, PVC, as a
minimum are suggested). Persons with asthmatic conditions chronic bronchitis, other chronic respiratory diseased,
recurrent eczema or pulmonary sensitization should be excluded from working with MDl. Once a person is diagnosed as
having pulmonary sensitization (allergic asthma) to MDl, further exposure is not permissible.
SECTION 5: FIRE FIGHTING MEASURES
Flash Point: >93.3’C, Closed Cup.
Autoignition: >600’C.
Flammable Limits: Not available.
Products of Combustion: Carbon Monoxide, Carbon Dioxide, Nitrous Oxide and HCN

J
Fire Hazards in Presence of Various Substances: Slightly flammable to flammable in presence of open flames, sparks
and static discharge or combustible materials.
Fire Fighting Media and lnstructions: Small Fire: Use DRY chemical powder.
Large Fire: Use water spray, fog or foam. Do not use water jet.
Protective Clothing (Fire): Splash goggles. Full suit. Boots. Gloves. A self-contained breathing apparatus should be
used to avoid inhalation of the product.
Special Remarks on Fire Hazards: Reacts slowly with water to produce carbon dioxide, which may rupture closed
containers. This reaction accelerates at higher temperatures.
SECTION 6: ACGIDENTAL RELEASE MEASURES
For major spills call Ghemtrec (800424-9300)
Small Spill and Leak: Clean-up should only be performed by trained personnel. People dealing with major spillages
should wear full protective clothing including appropriate respiratory protection. Evacuate the area. Prevent further
leakage, spillage or entry into drains.
Large Spill and Leak: Contain and absorb large spillages onto an inert, non-flammable adsorbent carrier (such as earth
or sand). Shovel into open-top drums or plastic bags for further decontamination, if necessary. Wash the spillage area
with
Liquid decontaminant. Test atmosphere for MDl. Neutralize small spillages with decontaminant. Remove and properly
dispose of residues (see Section 13 for disposal considerations). Notify applicable government authorities if release is
reportable. The CERCLA RQ for 4,4-MDl is 5000 lbs (see CERCLA in Section 15).
Decontaminant: Preparation of Decontaminant Solution: Prepare a decontamination solution of 0.2-0.5% liquid detergent
and 3-B% concentrated ammonium hydroxide in water (5-10% sodium carbonate may be substituted for ammonium
hydroxide). Follow the precautions on the supplier’s material safety data sheets when preparing and using solution.
Use of Decontamination Solution: Allow deactivated material to stand for at least 30 minutes before shoveling into drums.
Do not tighten the bungs. Mixing with wet earth is also effective, but slower.
SECTION 7: HANDLING AND STORAGE
Handling: Avoid personal contactwith the product or reaction mixture. Use only with adequate ventilation to ensure that
the occupational exposure limit is not exceeded. The efficiency of the ventilation system must be monitored regularly
because of the possibility of blockage. Avoid breathing aerosols, mists and vapors. (See Section B Exposure Control for
details.)
Storage: Keep containers properly sealed and when stored indoors, in a well ventilated area. Keep contents away from
moisture. Due to reaction with water, producing CO2-gas, a hazardous build-up of pressure could result if contaminated
containers are re-sealed. Do not reseal contaminated containers. Uncontaminated containers, free of moisture, may be
resealed only after placing under a nitrogen blanket. Do not store in containers made of cooper, cooper alloys or
galvanized surfaces.
ldeal storage temperature is 16-38oC (60-100″F).
Keep stocks of decontaminant (see Section 6) readily available.
SECTION 8: EXPOSURE CONTROLS, PERSONAL PROTECTION
Preventive Measures: Conditions of use, adequacy of engineering or other control measures, and actual exposures will
dictate the need for specific protective devices at your workplace.
Engineering Controls: Use local exhaust ventilation to maintain airborne concentrations bellow the TLV. Suitable
respiratory equipment should be used in cases of insufficient ventilation or where operational procedu res demand it. For

4
guidance on engineering control measures refer to publications such as the ACGIH current edition of ” lndustrial
Ventilation, a manual of Recommended Practice”.
Personal Protection
Eyes: Chemical safety goggles. lf there is a potential for splashing, use a full face shield
Body and Hands: The following protective materials are recommended: Gloves-neoprene, nitrile rubber, butyl
rubber. Thin latex disposable gloves should be avoided for repeated or long term use. Protective clothing should be
selected and used in accordance with “Guidelines for the Selection of Chemical Protective Clothing” published by ACGIH.
Respiratory: When the product is sprayed or heated without adequate ventilation, an approved MSHA/NIOSH
positive-pressure, supplied-air respirator may be required. Air purifying respirators equipped with organic vapor cartridges
and a HEPA (P100) particulate filter may be used under certain conditions when a cartridge change-out schedule has
been developed in accordance with the OSHA respiratory protection standard (29 C.F.R. 1910.134).
Personal Protection in Case of a Large Spills: Splash goggles. Full suit. Vapor respirator or a self-contained breathing
apparatus. Boots. Gloves. Suggested protective clothing might not be sufficient; consult a specialist BEFORE handling
this product.
Product Name Exposure Limits
4,4-Diphenylmethane Diisocyanate ACGIH TLV
OSHA PEL Ceiling Limit
NIOSH REL/TWA
NIOSH REL/CEILING
0.05 mg/m3 (8-hour, 40 hours/week)
0.20 mg/m3
0.05 mg/m3 (1O-hour, 40 hours/week)
0.20 mg/m3 (‘1 0-minutes)
Exposure control/ personal protection: Medical supervision of all employees who handle or come in contact with
respiratory sensitizers is recommended. Persons with respiratory problems including asthmatlc-type conditions, chronic
Bronchitis, other chronic respiratory diseases or recurrent skin eczema or skin allergies should be evaluated for their
suitability of working with this product. Once a person is diagnosed as sensitized, no further exposure to the material that
caused the sensitization should be permitted. The Occupational Exposure limits do not apply to previously sensitized
individuals.
SECTION 9: PHYSICAL AHD CHEMICAL PROPERTIES
APPEARANCE AND ODOR
BOtLtNG POTNT (.C)
MELTING POINT (‘F/”C)
SPECIFIC GRAVITY ( WATER = 1)
BULK DENSITY
pH
VAPOR PRESSURE (MM Hg.)
VAPOR DENSTTY (ArR-1)
VISCOSITY
PERCENT (%)VOC
FLASH POINTS
Brown Liquid Slightly Musty
>300’c
Not available
1.23 grlml
9.0 lb/gal
Not applicable
0.000004 mmHg @25″C
8.5
900-1300 cps @ 25’C
0%
>93.3″C (230’F) Closed Cup
SECTION 10: STABILITY AND REACTIVITY
Stability: Stable at room temperature.
lncompatibility with various Substances: Reactive with moisture.
Conditions of lnstability: Avoid high temperatures. Avoid freezing.
Hazardous Decomposition Products: Carbon Monoxide, Carbon Dioxide, Nitrous Oxide and HCN.
Hazardous Polymerization: Polymerization may occur at elevated temperatures in the presence of alkalies, tertiary
amines and metal compounds.

5
SECTION 1 1 : TOXICOLOGICAL INFORMATION
Toxicity to Animals: LD50 Rat Oral: >5000m9/kg
LD50 Rabbit Dermal: >5000 mg/kg
lnhalation: This product is a respiratory irritantand potential respiratory sensitizer. Repeated inhalation of vaporor
aerosol at levels above the occupational exposure limit could cause respiratory sensitization. Symptoms may include
irritation to the eyes, nose, throat and lungs, possibly combined with dryness of the throat, tightness of chest and difficulty
in breathing. The onset of the respiratory symptoms may be delayed for several hours after exposure. A hyper-reactive
response to even minimal concentrations of MDI may develop in sensitized persons.
Skin Contact: Moderate irritant. Repeated and/or prolonged contact may cause skin sensitization. There is limited
evidence from animal studies that skin contact may play a role in respiratory sensitization. These results emphasize the
need for protective clothing including gloves to be worn at all times when handling these chemicals or in maintenance
work.
Eye Contact: The vapor, aerosol, and liquid are irritant.
lngestion: lngestion may cause irritation of the gastrointestinaltract. Based on the acute oral LD50 this product is
considered practically non{oxic by ingestion.
Remarks: Short term test have shown that it is unlikely to be genotoxic. (BUTYLATEDHYDROXYTOLUENE)
Carcinogenic Effects: The ingredients of this product are not classified as carcinogenic by ACGIH or IARC, not
regulated as carcinogens by OSHA, and not listed as carcinogens by NTP.
Mutagenic Effects: There is no substantial evidence of mutagenic potential.
Reproductive Effects: No adverse reproductive effects are anticipated.
Teratogenic Effects: No birth defects were seen in two independent animal (rat) studies. Fetotoxicity was observed at
doses that were extremely toxic (including lethal) to the mother. Fetotoxicity was not observed at doses that were not
maternally toxic. The doses used in these studies were maximal respirable concentrations well in excess of the defined
limits.
Remark: A study was conducted where groups of rats were exposed for 6 hours/day, 5 days/week for a lifetime to
atmosphere of respirable polymeric MDI aerosol at concentrations of 0, 0.2,
‘1
or 6 mg/m3. No adverse effects were
observed at 0.2 mg/m3. At the 1mg/m3 concentration, minimal nasal and lung irritant effect were seen. Only at the top
concentration (6.0 mg/m3) was there an increased incidence of a benign tumor of the lung (adenoma). One malignant
pulmonary tumor (adenocarcinoma) was seen in the 6.0 mg/m3 group. MDI administration to rats in this study did not
change the distribution and incidence of tumors from those seen in controlanimals. The increased incidence of lung
tumors is associated with prolonged respiratory irritation and the concurrent accumulation of yellow materialin the lung. ln
the absence of prolonged exposure to high concentration leading to chronic irritation and lung damage, it is highly unlikely
that tumor formation will occur.
There are reports that excessive chronic exposure to diisocyanates may result in permanent decrease in lung function.
SECTION 12: EGOLOGICAL INFORMATION
Ecotoxicity: Polymeric MDl. LC50 (Zebra Fish) >1000 ml/|. EC50 (Daphnia magna) (24 hours) >1000 mg/l EC50 (E. Coli)
> 100m1/l
Environmentat Fate and Distribution: lt is unlikely that significant environmental exposure in the air or water will arise
based on consideration of the production and use of the substance.
Persistence and Degradation: lmmiscible with water, but will react with water to produce inert and non-biodegradable
solids.
SECTION 13: DISPOSAL CONSIDERATIONS

6
Waste lnformation: The generation of waste should be avoided or minimized wherever possible.
Disposal should be in accordance with local, state, provincial or national regulations, This material is not hazardous waste
under RCRA 40 CFR 261. Small quantities should be treated with a decontaminant solution (see Section 6). The treated
waste is not a hazardous material under RCRA 40 CFR 261. Chemicalwaste, even small quantities, should never be
poured down drains, sewers or watenruays.
Empty containers should be decontaminated and either passed to an approved drum recycler or destroyed.
SECTION 14: TRANSPORT INFORMATION
For major spills call Chemtrec (800424-9300).
DOT Classification: Single containers less than 5000 lbs. are not regulated. Single containers with 5000 lbs. Or more of
4,4-Methylene Diphenyl Diisocyanate are regulated as: Other Regulated Substances, Liquid, N.O.S. (Methylene Diphenyl
Diisocyanate), 9, NA30B2, Pclll, RQ.
TDG Classification: Not regulated.
IMO/IMDG Classification: Not regulated.
ICAO/IATA Glassification: Not regulated.
SECTION 15: REGULATORY INFORMATION
U.S. Federal Regulations
This material is classified as hazardous under OSHA Hazard Communication Standard (29 CFR 1910.1200).
HCS Classification: Class: Toxic
Class: lrritating substance.
Class: Sensitizing substance
TSCA B(b) inventory: All lngredients Listed
EPCRA Section 313 (40 CFR 372)
Diisocyanate Compounds (Category Code N120) 100%
CERCLA (Comprehensive Environmental Response, Compensation and Liability Act):
This product does not contain nor is it manufactured with ozone depleting substances.
State Regulations:
Canadian Regulations: This material has been classified in accordance with the hazard criteria of the CPR (Controlled
Products Regulations) and this MSDS (Material Safety Data Sheet) contains all the information required by the CPR,
WHMIS (Canada): Class D-1A: Material causing immediate and serious toxic effects (VERY TOXIC).
Class D-2A: Material causing other toxic effects (VERY TOXIC)’
Class D-2B: Material causing other toxic effects (TOXIC)’
CEPA: DSL/NDSL: All lngredients Listed.
SECTION 16: OTHER INFORMATION
CAUSES DAMAGE TO THE FOLLOWING ORGANS: LUNGS, RESPIRATORY TRACT, SKIN AND EYES. MAY BE
HARMFULL IF INHALED. MAY CAUSE RESPIRATORY TRACT, EYE AND SKIN IRRITATION. MAY CAUSE ALLERGIC
RESPIRATORY AND SKIN REACTION.

7
Hazardous Material lnformation System (U.S.A’)
Health: 2 Fire Hazard: 1 Reactivity: 1
National Fire Protection Association (U.S.A.)
Health: 2 FireHazard:1 Reactivity: 1
White the information and recommendations in this publication are to the best of our knowledge, information and belief accurate at the date
of pubtication, NOTHIN? HERETN tS TO BE CONSTRUED AS A WARRANTy, EXPRESS OR OTHERWISE-
IN ALL CASES, IT IS THE RESPONSIBILITY OF THE USER TO DETERMINE THE APPLICATION OF SUCH INFORMATION AND
RECOMMENDATIONS AND SUITABILITY OF ANY PRODIJCT FOR IRS OWN PARTICULAR PURPOSE.
THE PRODUCT MAY PRESENT HAZARD AND SHOULD BE USED WITH CAUTION, WHILE CERTAIN HAZARDS ARE DESCRIBED IN THIS
PIJBLICATION, NO GUARANTEE IS MADE THAT ARE THE ONLY HAZARDS THAT EXIST,
Hazards, toxicity and behavior of the products may differ when used with other materials and are dependent upon the manufactu ring
circumstances or other processes. Such hazards, toxicity and behavior should be determined by the user and made known to handlers’
processors and end users.
We disclaim liability for damage or injury incurring directly or indirectly from the use of this product’
APROVED AND AUTHORIZED BY: EnesTorlic

25HP8104BF_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8100 SERIES B-SIDE
Safety Data Sheet dated: 7/27/2023 – version 5
Date of first edition: 2/7/2023
1. IDENTIFICATION
Product identifier
Mixture identification:
Trade name:HP 8100 SERIES B-SIDE
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use:N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company:ETECO INC.
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable:N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION
Classification of the chemical
Label elements
Hazards not otherwise classified identified during the classification process:
None
Additional classification information
HMIS Health:0 = MINIMAL
HMIS Flammability:0 = Not Combustible
HMIS Reactivity:0 = MINIMAL
HMIS P.P.E.:Safety glasses, gloves
Specific target organ toxicity following repeated exposure,
Category 2
May cause damage to organs through prolonged or repeated
exposure.
Hazard pictograms and Signal Word
Warning
Hazard statements
H373 May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P314 Get medical advice/attention if you feel unwell.
P501 Dispose of contents/container to …
Page n. of1 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

HMIS P.P.E.:Safety glasses, gloves
NFPA Health:0 = MINIMAL
NFPA Flammability:0 = Not Combustible
NFPA Reactivity:0 = MINIMAL
NFPA Special Risk:NONE
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
N.A.
Mixtures
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification:
List of components
Qty Name Ident. Numb. Classification Registration Number
< 10 % Diethylene glycol CAS:111-46-6 Acute Tox. 4, H302; STOT RE 2, H373 The actual concentration of the components listed above is withheld as a trade secret. 4. FIRST AID MEASURES Description of first aid measures In case of skin contact: Immediately take off all contaminated clothing. Areas of the body that have - or are only even suspected of having - come into contact with the product must be rinsed immediately with plenty of running water and possibly with soap. Wash thoroughly the body (shower or bath). Remove contaminated clothing immediatley and dispose off safely. In case of eyes contact: Wash immediately with water. In case of Ingestion: Do not induce vomiting, get medical attention showing the SDS and label hazardous. In case of Inhalation: Remove casualty to fresh air and keep warm and at rest. Most important symptoms/effects, acute and delayed N.A. Indication of any immediate medical attention and special treatment needed In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible). 5. FIRE-FIGHTING MEASURES Extinguishing media Suitable extinguishing media: Water. Carbon dioxide (CO2). Unsuitable extinguishing media: None in particular. Specific hazards arising from the chemical Do not inhale explosion and combustion gases. Burning produces heavy smoke. Hazardous combustion products:N.A. Explosive properties:N.A. Oxidizing properties:N.A. Special protective equipment and precautions for fire-fighters Use suitable breathing apparatus . Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Move undamaged containers from immediate hazard area if it can be done safely. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Wear personal protection equipment. Remove persons to safety. See protective measures under point 7 and 8. Methods and material for containment and cleaning up Page n. of2 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate Methods and material for containment and cleaning up Suitable material for taking up: absorbing material, organic, sand Wash with plenty of water. 7. HANDLING AND STORAGE Precautions for safe handling Avoid contact with skin and eyes, inhaltion of vapours and mists. Don't use empty container before they have been cleaned. Before making transfer operations, assure that there aren't any incompatible material residuals in the containers. Contamined clothing should be changed before entering eating areas. Do not eat or drink while working. See also section 8 for recommended protective equipment. Conditions for safe storage, including any incompatibilities Storage temperature:N.A. Incompatible materials: None in particular. Instructions as regards storage premises: Adequately ventilated premises. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Control parameters Appropriate engineering controls:N.A. Individual protection measures Eye protection: Not needed for normal use. Anyway, operate according good working practices. Protection for skin: Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton. Protection for hands: Use protective gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber. Respiratory protection: Use adequate protective respiratory equipment. No data available 9. PHYSICAL AND CHEMICAL PROPERTIES Information on basic physical and chemical properties Physical StateLiquid Appearance and colour:clear Odour:Mild Odour threshold:N.A. pH:N.A. Melting point / freezing point:N.A. Initial boiling point and boiling range:N.A. Flash point:N.A.Notes:closed up Evaporation rate:N.A. Upper/lower flammability or explosive limits:N.A. Vapour density:>1
Vapour pressure:N.A.
Relative density:8.80 lbm/gal
Solubility in water:Soluble
Solubility in oil:N.A.
Partition coefficient (n-octanol/water):N.A.
Auto-ignition temperature:N.A.
Decomposition temperature: N.A.
Viscosity:750.00 cPo
Explosive properties:N.A.
Oxidizing properties:N.A.
Solid/gas flammability:N.A.
Other information
Substance Groups relevant propertiesN.A.
Miscibility:N.A.
Fat Solubility:N.A.
Page n. of3 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

Fat Solubility:N.A.
Conductivity:N.A.
10. STABILITY AND REACTIVITY
Reactivity
Stable under normal conditions
Chemical stability
Data not available.
Possibility of hazardous reactions
None.
Conditions to avoid
Stable under normal conditions.
Incompatible materials
None in particular.
Hazardous decomposition products
None.
11. TOXICOLOGICAL INFORMATION
Information on toxicological effects
Toxicological Information of the Preparation
a) acute toxicity Not classified
Based on available data, the classification criteria are not met
b) skin corrosion/irritation Not classified
Based on available data, the classification criteria are not met
c) serious eye damage/irritation Not classified
Based on available data, the classification criteria are not met
d) respiratory or skin sensitisationNot classified
Based on available data, the classification criteria are not met
e) germ cell mutagenicity Not classified
Based on available data, the classification criteria are not met
f) carcinogenicity Not classified
Based on available data, the classification criteria are not met
g) reproductive toxicity Not classified
Based on available data, the classification criteria are not met
h) STOT-single exposure Not classified
Based on available data, the classification criteria are not met
i) STOT-repeated exposure The product is classified: Specific target organ toxicity following repeated exposure,
Category 2(H373)
j) aspiration hazard Not classified
Based on available data, the classification criteria are not met
Substance(s) listed on the IARC Monographs:
None
Substance(s) listed as OSHA Carcinogen(s):
None
Substance(s) listed as NIOSH Carcinogen(s):
None
Substance(s) listed on the NTP report on Carcinogens:
None
12. ECOLOGICAL INFORMATION
Toxicity
Adopt good working practices, so that the product is not released into the environment.
Eco-Toxicological Information:
List of Eco-Toxicological properties of the product
Page n. of4 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

Persistence and degradability
Bioaccumulative potential
Mobility in soil
Other adverse effects
N.A.
Not classified for environmental hazards.
No data available for the product
N.A.
N.A.
N.A.
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Recover, if possible. Send to authorised disposal plants or for incineration under controlled conditions. In so doing, comply with the local and
national regulations currently in force.
14. TRANSPORT INFORMATION
Not classified as dangerous in the meaning of transport regulations.
UN number
ADR-UN number: N.A.
DOT-UN Number: N.A.
IATA-Un number: N.A.
IMDG-Un number: N.A.
UN proper shipping name
ADR-Shipping Name: N.A.
DOT Proper Shipping Name: N.A.
IATA-Technical name:N.A.
IMDG-Technical name: N.A.
Transport hazard class(es)
ADR-Class:N.A.
DOT Hazard Class:N.A.
IATA-Class:N.A.
IMDG-Class:N.A.
Packing group
ADR-Packing Group: N.A.
DOT Packing Group:N.A.
IATA-Packing group:N.A.
IMDG-Packing group: N.A.
Environmental hazards
Marine pollutant:No
Environmental Pollutant:N.A.
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N.A.
Special precautions
Department of Transportation (DOT):
N.A.
Road and Rail (ADR-RID):
N.A.
Air (IATA):
N.A.
Sea (IMDG):
N.A.
15. REGULATORY INFORMATION
USA – Federal regulations
TSCA – Toxic Substances Control Act
TSCA inventory:
Page n. of5 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

SARA – Superfund Amendments and Reauthorization Act
CERCLA – Comprehensive Environmental Response, Compensation, and Liability Act
CAA – Clean Air Act
CWA – Clean Water Act
USA – State specific regulations
California Proposition 65
Massachusetts Right to know
Pennsylvania Right to know
New Jersey Right to know
No substances listed
TSCA listed substances:
No substances listed
Section 302 – Extremely Hazardous Substances:
No substances listed
Section 304 – Hazardous substances:
No substances listed
Section 313 – Toxic chemical list:
No substances listed
Substance(s) listed under CERCLA:
No substances listed
CAA listed substances:
No substances listed
CWA listed substances:
No substances listed
Substance(s) listed under California Proposition 65:
No substances listed
Substance(s) listed under Massachusetts Right to know:
No substances listed
Substance(s) listed under Pennsylvania Right to know:
No substances listed
Substance(s) listed under New Jersey Right to know:
No substances listed
16. OTHER INFORMATION
Safety Data Sheet dated: 7/27/2023 – version 5
The information contained herein is based on our state of knowledge at the above-specified date. It refers solely to the product indicated and
constitutes no guarantee of particular quality. The information relates only to the specific material and may not be valid for such material
used in combination with any other material or in any process.
This document was prepared by a competent person who has received appropriate training.
It is the duty of the user to ensure that this information is appropriate and complete with respect to the specific use intended.
This MSDS cancels and replaces any preceding release.
Legend to abbreviations and acronyms used in the safety data sheet:
ADR:European Agreement concerning the International Carriage of Dangerous Goods by Road.
RID:Regulation Concerning the International Transport of Dangerous Goods by Rail.
Code Description
H302 Harmful if swallowed.
H373 May cause damage to organs through prolonged or repeated exposure.
Code Hazard class and hazard category Description
A.1/4/Oral Acute Tox. 4 Acute toxicity (oral), Category 4
A.9/2 STOT RE 2 Specific target organ toxicity following repeated exposure, Category 2
Page n. of6 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

RID:Regulation Concerning the International Transport of Dangerous Goods by Rail.
IMDG:International Maritime Code for Dangerous Goods.
IATA:International Air Transport Association.
IATA-DGR:Dangerous Goods Regulation by the “International Air Transport Association” (IATA).
ICAO:International Civil Aviation Organization.
ICAO-TI:Technical Instructions by the “International Civil Aviation Organization” (ICAO).
GHS:Globally Harmonized System of Classification and Labeling of Chemicals.
CLP:Classification, Labeling, Packaging.
EINECS:European Inventory of Existing Commercial Chemical Substances.
INCI:International Nomenclature of Cosmetic Ingredients.
CAS:Chemical Abstracts Service (division of the American Chemical Society).
GefStoffVO:Ordinance on Hazardous Substances, Germany.
LC50:Lethal concentration, for 50 percent of test population.
LD50:Lethal dose, for 50 percent of test population.
DNEL:Derived No Effect Level.
PNEC:Predicted No Effect Concentration.
TLV:Threshold Limiting Value.
TWATLV:Threshold Limit Value for the Time Weighted Average 8 hour day. (ACGIH Standard).
STEL:Short Term Exposure limit.
STOT:Specific Target Organ Toxicity.
WGK:German Water Hazard Class.
KSt:Explosion coefficient.
The information in this SDS is provided all the relevant data fully and truly. However, the information is provided without any
warranty on their absolute extensiveness and accuracy. This SDS was prepared to provide safety preventive measures for the users
who have got professional training. The personal user who obtained this SDS should make independent judgment for the
applicability of this SDS under special conditions. In these special cases, we do not assume responsibility for the damage.
Paragraphs modified from the previous revision:
– Safety Data Sheet
– 1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY/UNDERTAKING
– 3. COMPOSITION/INFORMATION ON INGREDIENTS
– 8. EXPOSURE CONTROLS/PERSONAL PROTECTION
– 9. PHYSICAL AND CHEMICAL PROPERTIES
– 11. TOXICOLOGICAL INFORMATION
Page n. of7 77/28/2023 Production Name HP 8100 SERIES B-SIDEDate

25HP8104AF_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8100 SERIES A SIDE
Safety Data Sheet dated: 7/28/2023 – version 7
Date of first edition: 1/16/2023
1. IDENTIFICATION
Product identifier
Mixture identification:
Trade name:HP 8100 SERIES A SIDE
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use:N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company:ETECO INC.
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable:N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION
Classification of the chemical
Label elements
Skin irritation, Category 2 Causes skin irritation.
Eye irritation, Category 2A Causes serious eye irritation.
Respiratory Sensitization, Category 1 May cause allergy or asthma symptoms or breathing difficulties if
inhaled.
Skin Sensitization, Category 1 May cause an allergic skin reaction.
Carcinogenicity, Category 2 Suspected of causing cancer.
Specific target organ toxicity following single exposure,
Category 3
May cause respiratory irritation.
Specific target organ toxicity following repeated exposure,
Category 2
May cause damage to organs through prolonged or repeated
exposure.
Acute toxicity (inhalation), Category 4 Harmful if inhaled.
Hazard pictograms and Signal Word
Danger
Hazard statements
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
Page n. of1 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Hazards not otherwise classified identified during the classification process:
None
Additional classification information
HMIS Health:3 = SERIOUS
HMIS Flammability:0 = Not Combustible
HMIS Reactivity:0 = MINIMAL
HMIS P.P.E.:Safety glasses, gloves
NFPA Health:3 = SERIOUS
NFPA Flammability:0 = Not Combustible
NFPA Reactivity:0 = MINIMAL
NFPA Special Risk:NONE
H373 May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
P201 Obtain special instructions before use.
P202 Do not handle until all safety precautions have been read and understood.
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P261 Avoid breathing dust/fume/gas/mist/vapours/spray.
P264 Wash … Thoroughly after handling.
P271 Use only outdoors or in a well-ventilated area.
P272 Contaminated work clothing must not be allowed out of the workplace.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P284 [In case of inadequate ventilation] wear respiratory protection.
P302+P352 IF ON SKIN: Wash with plenty of water/
P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.
P304+P341 IF INHALED: If breathing is difficult, remove victim to fresh air and keep at rest in a position comfortable
for breathing.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy
to do. Continue rinsing.
P308+P313 IF exposed or concerned: Get medical advice/attention.
P310 Immediately call a POISON CENTER/doctor/
P312 Call a POISON CENTER/doctor/ if you feel unwell.
P314 Get medical advice/attention if you feel unwell.
P320 Specific treatment is urgent (see … On this label).
P321 Specific treatment (see … On this label).
P332+P313 If skin irritation occurs: Get medical advice/attention.
P333+P313 If skin irritation or rash occurs: Get medical advice/attention.
P337+P313 If eye irritation persists: Get medical advice/attention.
P342+P311 If experiencing respiratory symptoms: Call a POISON CENTER/doctor/
P362+P364 Take off contaminated clothing and wash it before reuse.
P363 Wash contaminated clothing before reuse.
P403+P233 Store in a well-ventilated place. Keep container tightly closed.
P405 Store locked up.
P501 Dispose of contents/container to …
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
N.A.
Mixtures
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification:
List of components
Qty Name Ident. Numb. Classification Registration Number
Page n. of2 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Qty Name Ident. Numb. Classification Registration Number
60-80 % DIPHENYLMETHANEDIISOCYANATE CAS:9016-87-9 Skin Irrit. 2, H315; Eye Irrit. 2A,
H319; STOT SE 3, H335; STOT RE
2, H373; Resp. Sens. 1, H334
30-70 % 4,4′-METHYLENEDIPHENYL
DIISOCYANATE
CAS:101-68-8 Acute Tox. 4, H332; Skin Irrit. 2,
H315; Eye Irrit. 2A, H319; Carc. 2,
H351; STOT SE 3, H335; STOT RE
2, H373; Resp. Sens. 1, H334;
Skin Sens. 1, H317
The actual concentration of the components listed above is withheld as a trade secret.
4. FIRST AID MEASURES
Description of first aid measures
In case of skin contact:
Immediately take off all contaminated clothing.
Remove contaminated clothing immediatley and dispose off safely.
After contact with skin, wash immediately with soap and plenty of water.
In case of eyes contact:
After contact with the eyes, rinse with water with the eyelids open for a sufficient length of time, then consult an opthalmologist
immediately.
Protect uninjured eye.
In case of Ingestion:
Do not induce vomiting, get medical attention showing the SDS and label hazardous.
In case of Inhalation:
If breathing is irregular or stopped, administer artificial respiration.
In case of inhalation, consult a doctor immediately and show him packing or label.
Most important symptoms/effects, acute and delayed
Eye irritation
Eye damages
Skin Irritation
Erythema
Indication of any immediate medical attention and special treatment needed
In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible).
5. FIRE-FIGHTING MEASURES
Extinguishing media
Suitable extinguishing media:
Water.
Carbon dioxide (CO2).
Unsuitable extinguishing media:
None in particular.
Specific hazards arising from the chemical
Do not inhale explosion and combustion gases.
Burning produces heavy smoke.
Hazardous combustion products:N.A.
Explosive properties:N.A.
Oxidizing properties:N.A.
Special protective equipment and precautions for fire-fighters
Use suitable breathing apparatus .
Collect contaminated fire extinguishing water separately. This must not be discharged into drains.
Move undamaged containers from immediate hazard area if it can be done safely.
6. ACCIDENTAL RELEASE MEASURES
Personal precautions, protective equipment and emergency procedures
Wear personal protection equipment.
Wear breathing apparatus if exposed to vapours/dusts/aerosols.
Provide adequate ventilation.
Use appropriate respiratory protection.
See protective measures under point 7 and 8.
Methods and material for containment and cleaning up
Suitable material for taking up: absorbing material, organic, sand
Page n. of3 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Wash with plenty of water.
7. HANDLING AND STORAGE
Precautions for safe handling
Avoid contact with skin and eyes, inhaltion of vapours and mists.
Exercise the greatest care when handling or opening the container.
Do not use on extensive surface areas in premises where there are occupants.
Use localized ventilation system.
Don’t use empty container before they have been cleaned.
Before making transfer operations, assure that there aren’t any incompatible material residuals in the containers.
Contamined clothing should be changed before entering eating areas.
Do not eat or drink while working.
See also section 8 for recommended protective equipment.
Conditions for safe storage, including any incompatibilities
Storage temperature:N.A.
Always keep in a well ventilated place.
Incompatible materials:
None in particular.
Instructions as regards storage premises:
Cool and adequately ventilated.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
Control parameters
Appropriate engineering controls:N.A.
Individual protection measures
Eye protection:
Use close fitting safety goggles, don’t use eye lens.
Protection for skin:
Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton.
Protection for hands:
Use protective gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber.
Respiratory protection:
Use adequate protective respiratory equipment.
No data available
9. PHYSICAL AND CHEMICAL PROPERTIES
Information on basic physical and chemical properties
Physical StateLiquid
Appearance and colour:brown
Odour:Slightly Musty
Odour threshold:N.A.
pH:N.A.
Melting point / freezing point:N.A.
Initial boiling point and boiling range:300 C (572 F)
Flash point:N.A.
Evaporation rate:N.A.
Upper/lower flammability or explosive limits:N.A.
Vapour density:8.5
Vapour pressure:0.000004 mmHg @ 25 C
Relative density:9.00 lbm/gal
Solubility in water:N.A.
Solubility in oil:N.A.
Partition coefficient (n-octanol/water):N.A.
Auto-ignition temperature:N.A.
Decomposition temperature: N.A.
Viscosity:1,100.00 cPo
Explosive properties:N.A.
Oxidizing properties:N.A.
Solid/gas flammability:N.A.
Other information
Substance Groups relevant propertiesN.A.
Page n. of4 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Substance Groups relevant propertiesN.A.
Miscibility:N.A.
Fat Solubility:N.A.
Conductivity:N.A.
10. STABILITY AND REACTIVITY
Reactivity
Stable under normal conditions
Chemical stability
Data not available.
Possibility of hazardous reactions
None.
Conditions to avoid
Stable under normal conditions.
Incompatible materials
None in particular.
Hazardous decomposition products
None.
11. TOXICOLOGICAL INFORMATION
Information on toxicological effects
Toxicological Information of the Preparation
a) acute toxicity The product is classified: Acute toxicity (inhalation), Category 4(H332)
b) skin corrosion/irritation The product is classified: Skin irritation, Category 2(H315)
c) serious eye damage/irritation The product is classified: Eye irritation, Category 2A(H319)
d) respiratory or skin sensitisationThe product is classified: Respiratory Sensitization, Category 1(H334), Skin
Sensitization, Category 1(H317)
e) germ cell mutagenicity Not classified
Based on available data, the classification criteria are not met
f) carcinogenicity The product is classified: Carcinogenicity, Category 2(H351)
g) reproductive toxicity Not classified
Based on available data, the classification criteria are not met
h) STOT-single exposure The product is classified: Specific target organ toxicity following single exposure,
Category 3(H335)
i) STOT-repeated exposure The product is classified: Specific target organ toxicity following repeated exposure,
Category 2(H373)
j) aspiration hazard Not classified
Based on available data, the classification criteria are not met
Substance(s) listed on the IARC Monographs:
None
Substance(s) listed as OSHA Carcinogen(s):
None
Substance(s) listed as NIOSH Carcinogen(s):
None
Substance(s) listed on the NTP report on Carcinogens:
None
12. ECOLOGICAL INFORMATION
Toxicity
Adopt good working practices, so that the product is not released into the environment.
Eco-Toxicological Information:
Persistence and degradability
List of Eco-Toxicological properties of the product
Not classified for environmental hazards.
No data available for the product
Page n. of5 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Bioaccumulative potential
Mobility in soil
Other adverse effects
N.A.
N.A.
N.A.
N.A.
13. DISPOSAL CONSIDERATIONS
Waste treatment methods
Recover, if possible. Send to authorised disposal plants or for incineration under controlled conditions. In so doing, comply with the local and
national regulations currently in force.
14. TRANSPORT INFORMATION
UN number
ADR-UN number: 3082
DOT-UN Number: UN3082
IATA-Un number: 3082
IMDG-Un number: 3082
UN proper shipping name
ADR-Shipping Name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
DOT Proper Shipping Name: Environmentally hazardous substance, liquid, n.o.s.
IATA-Technical name:ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
IMDG-Technical name: ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S.
Transport hazard class(es)
ADR-Class:9
DOT Hazard Class:9
IATA-Class:9
IMDG-Class:9
Packing group
ADR-Packing Group: III
DOT Packing Group:III
IATA-Packing group:III
IMDG-Packing group: III
Environmental hazards
Marine pollutant:No
Environmental Pollutant:N.A.
Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code
N.A.
Special precautions
Department of Transportation (DOT):
DOT-Special Provision(s):8, 146, 173, 335, IB3, T4, TP1, TP29
DOT Label(s):9
DOT Symbol:N/A
DOT Cargo Aircraft:No limit
DOT Passenger Aircraft:No limit
DOT Bulk:241
DOT Non-Bulk:203
Road and Rail (ADR-RID):
ADR-Label:9
ADR – Hazard identification number:90
ADR-Transport category (Tunnel restriction code):3 (-)
Air (IATA):
IATA-Passenger Aircraft:964
IATA-Cargo Aircraft:964
IATA-Label:9
IATA-Subrisk:-
IATA-Erg:9L
Page n. of6 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

IATA-Erg:9L
IATA-Special Provisions:A97 A158 A197 A215
Sea (IMDG):
IMDG-Stowage Code: Category A
IMDG-Stowage Note: –
IMDG-Subrisk:-
IMDG-Special Provisions:274 335 969
IMDG-EMS: F-A, S-F
15. REGULATORY INFORMATION
USA – Federal regulations
TSCA – Toxic Substances Control Act
SARA – Superfund Amendments and Reauthorization Act
CERCLA – Comprehensive Environmental Response, Compensation, and Liability Act
CAA – Clean Air Act
CWA – Clean Water Act
USA – State specific regulations
California Proposition 65
Massachusetts Right to know
Pennsylvania Right to know
New Jersey Right to know
TSCA inventory:
No substances listed
TSCA listed substances:
No substances listed
Section 302 – Extremely Hazardous Substances:
No substances listed
Section 304 – Hazardous substances:
No substances listed
Section 313 – Toxic chemical list:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under CERCLA:
No substances listed
CAA listed substances:
No substances listed
CWA listed substances:
No substances listed
Substance(s) listed under California Proposition 65:
No substances listed
Substance(s) listed under Massachusetts Right to know:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under Pennsylvania Right to know:
4,4′-METHYLENEDIPHENYL DIISOCYANATE
Substance(s) listed under New Jersey Right to know:
No substances listed
16. OTHER INFORMATION
Page n. of7 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

Safety Data Sheet dated: 7/28/2023 – version 7
The information contained herein is based on our state of knowledge at the above-specified date. It refers solely to the product indicated and
constitutes no guarantee of particular quality. The information relates only to the specific material and may not be valid for such material
used in combination with any other material or in any process.
This document was prepared by a competent person who has received appropriate training.
It is the duty of the user to ensure that this information is appropriate and complete with respect to the specific use intended.
This MSDS cancels and replaces any preceding release.
Legend to abbreviations and acronyms used in the safety data sheet:
ADR:European Agreement concerning the International Carriage of Dangerous Goods by Road.
RID:Regulation Concerning the International Transport of Dangerous Goods by Rail.
IMDG:International Maritime Code for Dangerous Goods.
IATA:International Air Transport Association.
IATA-DGR:Dangerous Goods Regulation by the “International Air Transport Association” (IATA).
ICAO:International Civil Aviation Organization.
ICAO-TI:Technical Instructions by the “International Civil Aviation Organization” (ICAO).
GHS:Globally Harmonized System of Classification and Labeling of Chemicals.
CLP:Classification, Labeling, Packaging.
EINECS:European Inventory of Existing Commercial Chemical Substances.
INCI:International Nomenclature of Cosmetic Ingredients.
CAS:Chemical Abstracts Service (division of the American Chemical Society).
GefStoffVO:Ordinance on Hazardous Substances, Germany.
LC50:Lethal concentration, for 50 percent of test population.
LD50:Lethal dose, for 50 percent of test population.
DNEL:Derived No Effect Level.
PNEC:Predicted No Effect Concentration.
TLV:Threshold Limiting Value.
TWATLV:Threshold Limit Value for the Time Weighted Average 8 hour day. (ACGIH Standard).
STEL:Short Term Exposure limit.
STOT:Specific Target Organ Toxicity.
WGK:German Water Hazard Class.
KSt:Explosion coefficient.
The information in this SDS is provided all the relevant data fully and truly. However, the information is provided without any
warranty on their absolute extensiveness and accuracy. This SDS was prepared to provide safety preventive measures for the users
who have got professional training. The personal user who obtained this SDS should make independent judgment for the
applicability of this SDS under special conditions. In these special cases, we do not assume responsibility for the damage.
Code Description
H315 Causes skin irritation.
H317 May cause an allergic skin reaction.
H319 Causes serious eye irritation.
H332 Harmful if inhaled.
H334 May cause allergy or asthma symptoms or breathing difficulties if inhaled.
H335 May cause respiratory irritation.
H351 Suspected of causing cancer.
H373 May cause damage to organs through prolonged or repeated exposure.
Code Hazard class and hazard category Description
A.1/4/Inhal Acute Tox. 4 Acute toxicity (inhalation), Category 4
A.2/2 Skin Irrit. 2 Skin irritation, Category 2
A.3/2A Eye Irrit. 2A Eye irritation, Category 2A
A.4.1/1 Resp. Sens. 1 Respiratory Sensitization, Category 1
A.4.2/1 Skin Sens. 1 Skin Sensitization, Category 1
A.6/2 Carc. 2 Carcinogenicity, Category 2
A.8/3 STOT SE 3 Specific target organ toxicity following single exposure, Category 3
A.9/2 STOT RE 2 Specific target organ toxicity following repeated exposure, Category 2
Page n. of8 87/28/2023 Production Name HP 8100 SERIES A SIDEDate

25HP8103BD_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
HP 8100 SERIES B-SIDE
Safety Data Sheet dated: 3/9/2023 – version 3
Date of first edition: 2/7/2023
1. IDENTIFICATION
Product identifier
Mixture identification:
Trade name:HP 8100 SERIES B-SIDE
Recommended use of the chemical and restrictions on use
Recommended use: N.A.
Restrictions on use:N.A.
Name, address, and telephone number of the chemical manufacturer, importer, or other responsible party
Company:ETECO INC.
1000 S. Linwood Ave.
Santa Ana, CA 92705
Company Phone: + 001 714-480-1370
Responsable:N.A.
Emergency telephone number
Transportation Emergency Call Chemtrec: 800 424 9300
Medical Emergency Information: 800 328 8501
Manufacturer Contact: 1000 S. Linwood Ave Santa Ana, CA 92705 Company Phone: + 001 714-480-1370
2. HAZARD(S) IDENTIFICATION
Classification of the chemical
Label elements
Hazards not otherwise classified identified during the classification process:
None
Additional classification information
HMIS Health:0 = MINIMAL
HMIS Flammability:0 = Not Combustible
HMIS Reactivity:0 = MINIMAL
HMIS P.P.E.:Safety glasses, gloves
Specific target organ toxicity following repeated exposure,
Category 2
May cause damage to organs through prolonged or repeated
exposure.
Hazard pictograms and Signal Word
Warning
Hazard statements
H373 May cause damage to organs through prolonged or repeated exposure.
Precautionary statements
P260 Do not breathe dust/fume/gas/mist/vapours/spray.
P314 Get medical advice/attention if you feel unwell.
P501 Dispose of contents/container to …
Page n. of1 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate

HMIS P.P.E.:Safety glasses, gloves
NFPA Health:0 = MINIMAL
NFPA Flammability:0 = Not Combustible
NFPA Reactivity:0 = MINIMAL
NFPA Special Risk:NONE
3. COMPOSITION/INFORMATION ON INGREDIENTS
Substances
N.A.
Mixtures
Hazardous components within the meaning of 29 CFR 1910.1200 and related classification:
List of components
Qty Name Ident. Numb. Classification Registration Number
< 10 % Diethylene glycol CAS:111-46-6 Acute Tox. 4, H302; STOT RE 2, H373 4. FIRST AID MEASURES Description of first aid measures In case of skin contact: Immediately take off all contaminated clothing. Areas of the body that have - or are only even suspected of having - come into contact with the product must be rinsed immediately with plenty of running water and possibly with soap. Wash thoroughly the body (shower or bath). Remove contaminated clothing immediatley and dispose off safely. In case of eyes contact: Wash immediately with water. In case of Ingestion: Do not induce vomiting, get medical attention showing the SDS and label hazardous. In case of Inhalation: Remove casualty to fresh air and keep warm and at rest. Most important symptoms/effects, acute and delayed N.A. Indication of any immediate medical attention and special treatment needed In case of accident or unwellness, seek medical advice immediately (show directions for use or safety data sheet if possible). 5. FIRE-FIGHTING MEASURES Extinguishing media Suitable extinguishing media: Water. Carbon dioxide (CO2). Unsuitable extinguishing media: None in particular. Specific hazards arising from the chemical Do not inhale explosion and combustion gases. Burning produces heavy smoke. Hazardous combustion products:N.A. Explosive properties:N.A. Oxidizing properties:N.A. Special protective equipment and precautions for fire-fighters Use suitable breathing apparatus . Collect contaminated fire extinguishing water separately. This must not be discharged into drains. Move undamaged containers from immediate hazard area if it can be done safely. 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protective equipment and emergency procedures Wear personal protection equipment. Remove persons to safety. See protective measures under point 7 and 8. Methods and material for containment and cleaning up Suitable material for taking up: absorbing material, organic, sand Wash with plenty of water. Page n. of2 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate Wash with plenty of water. 7. HANDLING AND STORAGE Precautions for safe handling Avoid contact with skin and eyes, inhaltion of vapours and mists. Don't use empty container before they have been cleaned. Before making transfer operations, assure that there aren't any incompatible material residuals in the containers. Contamined clothing should be changed before entering eating areas. Do not eat or drink while working. See also section 8 for recommended protective equipment. Conditions for safe storage, including any incompatibilities Storage temperature:N.A. Incompatible materials: None in particular. Instructions as regards storage premises: Adequately ventilated premises. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Control parameters Appropriate engineering controls:N.A. Individual protection measures Eye protection: Not needed for normal use. Anyway, operate according good working practices. Protection for skin: Use clothing that provides comprehensive protection to the skin, e.g. cotton, rubber, PVC or viton. Protection for hands: Use protective gloves that provides comprehensive protection, e.g. P.V.C., neoprene or rubber. Respiratory protection: Use adequate protective respiratory equipment. No data available 9. PHYSICAL AND CHEMICAL PROPERTIES Information on basic physical and chemical properties Physical StateN.A. Appearance and colour:N.A. Odour:N.A. Odour threshold:N.A. pH:N.A. Melting point / freezing point:N.A. Initial boiling point and boiling range:N.A. Flash point:N.A. Evaporation rate:N.A. Upper/lower flammability or explosive limits:N.A. Vapour density:N.A. Vapour pressure:N.A. Relative density:N.A. Solubility in water:N.A. Solubility in oil:N.A. Partition coefficient (n-octanol/water):N.A. Auto-ignition temperature:N.A. Decomposition temperature: N.A. Viscosity:N.A. Explosive properties:N.A. Oxidizing properties:N.A. Solid/gas flammability:N.A. Other information Substance Groups relevant propertiesN.A. Miscibility:N.A. Fat Solubility:N.A. Conductivity:N.A. Page n. of3 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate 10. STABILITY AND REACTIVITY Reactivity Stable under normal conditions Chemical stability Data not available. Possibility of hazardous reactions None. Conditions to avoid Stable under normal conditions. Incompatible materials None in particular. Hazardous decomposition products None. 11. TOXICOLOGICAL INFORMATION Information on toxicological effects Toxicological Information of the Preparation a) acute toxicity Not classified Based on available data, the classification criteria are not met b) skin corrosion/irritation Not classified Based on available data, the classification criteria are not met c) serious eye damage/irritation Not classified Based on available data, the classification criteria are not met d) respiratory or skin sensitisationNot classified Based on available data, the classification criteria are not met e) germ cell mutagenicity Not classified Based on available data, the classification criteria are not met f) carcinogenicity Not classified Based on available data, the classification criteria are not met g) reproductive toxicity Not classified Based on available data, the classification criteria are not met h) STOT-single exposure Not classified Based on available data, the classification criteria are not met i) STOT-repeated exposure The product is classified: Specific target organ toxicity following repeated exposure, Category 2(H373) j) aspiration hazard Not classified Based on available data, the classification criteria are not met Substance(s) listed on the IARC Monographs: None Substance(s) listed as OSHA Carcinogen(s): None Substance(s) listed as NIOSH Carcinogen(s): None Substance(s) listed on the NTP report on Carcinogens: None 12. ECOLOGICAL INFORMATION Toxicity Adopt good working practices, so that the product is not released into the environment. Eco-Toxicological Information: Persistence and degradability List of Eco-Toxicological properties of the product Not classified for environmental hazards. No data available for the product Page n. of4 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate Persistence and degradability Bioaccumulative potential Mobility in soil Other adverse effects N.A. N.A. N.A. N.A. 13. DISPOSAL CONSIDERATIONS Waste treatment methods Recover, if possible. Send to authorised disposal plants or for incineration under controlled conditions. In so doing, comply with the local and national regulations currently in force. 14. TRANSPORT INFORMATION Not classified as dangerous in the meaning of transport regulations. UN number ADR-UN number: N.A. DOT-UN Number: N.A. IATA-Un number: N.A. IMDG-Un number: N.A. UN proper shipping name ADR-Shipping Name: N.A. DOT Proper Shipping Name: N.A. IATA-Technical name:N.A. IMDG-Technical name: N.A. Transport hazard class(es) ADR-Class:N.A. DOT Hazard Class:N.A. IATA-Class:N.A. IMDG-Class:N.A. Packing group ADR-Packing Group: N.A. DOT Packing Group:N.A. IATA-Packing group:N.A. IMDG-Packing group: N.A. Environmental hazards Marine pollutant:No Environmental Pollutant:N.A. Transport in bulk according to Annex II of MARPOL73/78 and the IBC Code N.A. Special precautions Department of Transportation (DOT): N.A. Road and Rail (ADR-RID): N.A. Air (IATA): N.A. Sea (IMDG): N.A. 15. REGULATORY INFORMATION USA - Federal regulations TSCA - Toxic Substances Control Act TSCA inventory: No substances listed TSCA listed substances: Page n. of5 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate SARA - Superfund Amendments and Reauthorization Act CERCLA - Comprehensive Environmental Response, Compensation, and Liability Act CAA - Clean Air Act CWA - Clean Water Act USA - State specific regulations California Proposition 65 Massachusetts Right to know Pennsylvania Right to know New Jersey Right to know No substances listed Section 302 - Extremely Hazardous Substances: No substances listed Section 304 - Hazardous substances: No substances listed Section 313 - Toxic chemical list: No substances listed Substance(s) listed under CERCLA: No substances listed CAA listed substances: No substances listed CWA listed substances: No substances listed Substance(s) listed under California Proposition 65: No substances listed Substance(s) listed under Massachusetts Right to know: No substances listed Substance(s) listed under Pennsylvania Right to know: No substances listed Substance(s) listed under New Jersey Right to know: No substances listed 16. OTHER INFORMATION Safety Data Sheet dated: 3/9/2023 - version 3 The information contained herein is based on our state of knowledge at the above-specified date. It refers solely to the product indicated and constitutes no guarantee of particular quality. The information relates only to the specific material and may not be valid for such material used in combination with any other material or in any process. This document was prepared by a competent person who has received appropriate training. It is the duty of the user to ensure that this information is appropriate and complete with respect to the specific use intended. This MSDS cancels and replaces any preceding release. Legend to abbreviations and acronyms used in the safety data sheet: ADR:European Agreement concerning the International Carriage of Dangerous Goods by Road. RID:Regulation Concerning the International Transport of Dangerous Goods by Rail. IMDG:International Maritime Code for Dangerous Goods. IATA:International Air Transport Association. IATA-DGR:Dangerous Goods Regulation by the "International Air Transport Association" (IATA). Code Description H302 Harmful if swallowed. H373 May cause damage to organs through prolonged or repeated exposure. Code Hazard class and hazard category Description A.1/4/Oral Acute Tox. 4 Acute toxicity (oral), Category 4 A.9/2 STOT RE 2 Specific target organ toxicity following repeated exposure, Category 2 Page n. of6 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate IATA-DGR:Dangerous Goods Regulation by the "International Air Transport Association" (IATA). ICAO:International Civil Aviation Organization. ICAO-TI:Technical Instructions by the "International Civil Aviation Organization" (ICAO). GHS:Globally Harmonized System of Classification and Labeling of Chemicals. CLP:Classification, Labeling, Packaging. EINECS:European Inventory of Existing Commercial Chemical Substances. INCI:International Nomenclature of Cosmetic Ingredients. CAS:Chemical Abstracts Service (division of the American Chemical Society). GefStoffVO:Ordinance on Hazardous Substances, Germany. LC50:Lethal concentration, for 50 percent of test population. LD50:Lethal dose, for 50 percent of test population. DNEL:Derived No Effect Level. PNEC:Predicted No Effect Concentration. TLV:Threshold Limiting Value. TWATLV:Threshold Limit Value for the Time Weighted Average 8 hour day. (ACGIH Standard). STEL:Short Term Exposure limit. STOT:Specific Target Organ Toxicity. WGK:German Water Hazard Class. KSt:Explosion coefficient. The information in this SDS is provided all the relevant data fully and truly. However, the information is provided without any warranty on their absolute extensiveness and accuracy. This SDS was prepared to provide safety preventive measures for the users who have got professional training. The personal user who obtained this SDS should make independent judgment for the applicability of this SDS under special conditions. In these special cases, we do not assume responsibility for the damage. Paragraphs modified from the previous revision: - 3. COMPOSITION/INFORMATION ON INGREDIENTS Page n. of7 73/9/2023 Production Name HP 8100 SERIES B-SIDEDate