by | Sep 27, 2025
SAFETY DATA SHEET
Page 1 of 6 Balsaflex
1 Product and Company Identification
Product identification: Balsaflex
Material identification: End-grain balsa wood (hard tropical wood) core material.
Application of the material: Structural core flexible panel
Product description: End-grain balsa wood flexible panel scrimmed with fiberglass fabric sheet
or scored and with or without surface coating.
Supplier/Manufacturer:
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012 .
However, when subject to machining or processing methods under normal condition of use, the release of wood
dust may pose some hazards if work is not performed under good industrial and safety practices. Risks of exposure
from these chemicals are specified below in line with the OSHA HCS classification.
DANGER!
– May cause an allergic skin reaction.
– May cause allergy or asthma symptoms or breathing difficulties if inhaled.
– May cause respiratory irritation.
– May cause cancer.
– Causes damage to respiratory system through prolonged or repeated exposure.
– May form combustible dust in the air.
Precautionary statements: – Do not breathe dust.
– Use only in a well-ventilated area.
– Wear protective gloves, protective clothing, eye protection.
– In case of inadequate ventilation, wear respira tory protection.
– Keep away from open flames and other ignition sources.
First aid: If experiencing respiratory symptoms, get medical attention.
If skin irritation or rash occurs get medical advice.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
Hazard classifications for wood dust: Skin sensitization 1
Respiratory sensitization 1
Carcinogenicity 1A
STOT SE3
STOT RE1
Combustible Dust
SAFETY DATA SHEET
Page 2 of 6 Balsaflex
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during a fire. Combustion by-product
include but are not limited to carbon dioxide, carbon monoxide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust, remove individual to fresh air. If condition persists, consult a physician.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide local exhaust ventilation during machining and processing operations to control airborne
contaminant exposure.
Wear appropriate personal protection when machining the product.
Storage: Protect from heat and open flames. This product should be stored according to the national or local
Fire Code.
3 Composition/Information on Ingredients
Date of issue: 28/05/15
Product contains no hazardous ingredients per 29 CFR 1910.1200.
SAFETY DATA SHEET
Page 3 of 6 Balsaflex
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name OSHA (PEL) ACGIH (TLV)
Particulates Not Otherwise Regulated (Total dust) 1 5 mg/m
3
(TWA) –
Particulates Not Otherwise Regulated (respirable fraction) 5 mg/m
3
(TWA) 1 mg/m
3
(TWA)
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved respirator with particulate cartridge if ventilation is not adequate and excessive
dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Ochre – white
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Not available
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 Balsaflex
11 Toxicological Information
Toxicological data: No data available
Route of exposure (when processing product): inhalation, eye, skin.
– Dust released when machining the product may cause irritation to upper respiratory tract.
– Dust released when machining the product may cause eye and skin irritation.
Sensitization: Wood dust may cause allergic contact dermatitis and respiratory sensitization with prolonged
and repetitive exposure.
Chronic toxicity:
– Prolonged exposure to wood dust by inhalation has been reported to be associated with nasal and
paranasal cancer. Wood dust is classified carcinogen (IARC Group 1)
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not expose to flame. Avoid ignition source along with dust cloud formed during
machining operations.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: None.
Hazardous decomposition products: Decomposition products include but are not limited to carbon
monoxide, carbon dioxide depending on condition of combustion.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
13 Disposal Considerations
Waste disposal: This product is stable and not hazardous. Waste generator should review appropriate
regulations.
SAFETY DATA SHEET
Page 5 of 6 Balsaflex
Regulatory status: This product is subject to hazardous classification only if machining the product
generates wood dust. See safety label attached to this Safety Data Sheet as required
by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: Drilling, sawing, sanding or machining wood products generates wood dust, a
substance known to the State of California to cause cancer.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
Date of issue: 28/05/15
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG; IATA): Not regulated for transport.
SAFETY LABEL
Page 6 of 6 Balsaflex
When this product is subject to processing methods under normal condition of use,
the release of wood dust may pose health risks and combustible dust hazard if work
is not performed under good industrial and safety practices.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
DANGER! WOOD DUST
– May cause an allergic skin reaction.
– May cause allergy or asthma symptoms or breathing difficulties if inhaled.
– May cause respiratory irritation.
– May cause cancer.
– Causes damage to respiratory system through prolonged or repeated exposure.
– May form combustible dust in the air.
Precautionary statements:
– Do not breathe dust.
– Use only in a well-ventilated area.
– Wear protective gloves, protective clothing, eye protection.
– In case of inadequate ventilation, wear respiratory protection.
– Keep away from open flames and other ignition sources.
First aid:
– If experiencing respiratory symptoms, get medical attention.
– If skin irritation or rash occurs get medical advice.
C
California proposition 65:
Drilling, sawing, sanding or machining wood products generates wood dust,
a substance known to the State of California to cause cancer.
Balsaflex
by | Sep 27, 2025
SAFETY DATA SHEET (SDS)
METYX
Glass Fiber Fabric
1
/5 FR-04-2/13.04.2015
1. Identification of the Substance and Company/Undertaking
1.1. Trade Name: METYX Glass Fiber Fabrics
1.2. Chemical Name: Fiber Glass
1.3. Scope: Industrial applications
1.4. Supplier Details:
METYX, USA, Inc.
2504 Lowell Road Gastonia NC 28054
Tel.: +1 704 824 1030
Web: www.metyx.com
e-Mail: metyx@metyx.com
Emergency Phone number: + 704 239 5671
2. Composition/Information on Ingredients
Continuous filament glass fiber including synthetic threading yarn
Ingredient name CAS Number: %
Glass, oxide, chemicals 65997 17 3 >95
Organic Surface Binder/Sizing Not available <5
Continuous filament glass fiber is a glass product which is given a specific shape (filament) and dimension
(filament diameter). A surface treatment (sizing) is applied to the filament which are gathered to form a strand. The
sizing is a mixture of chemicals, i.e. film former, coupling agent and polymeric resin/emulsion. The sizing content
is usually less than or equal to 2%. Non crimp fabrics made with glass fibers are stitched with synthetic yarns.
3. Hazards Identifications
The product is not classified as hazardous according to Regulation (EC) 1272/2008 as amended.
See Section 16 for the full text of the H statements declared above.
See Section 11 for more detailed information on health effects and symptoms.
Product definiton: Article . Classification according to Regulation (EC) No. 1272/2008 [CLP/GHS]
Under normal industrial conditions, product is not flammable and has stability.
3.1. Skin: Directly contact with skin may cause irritation, itching, rash, and swelling. Wear protective clothes.
3.2. Eye: May cause eye irritation, rash, pain. These symptoms may continue after stop working. This condition
may be temporary but may cause permanent influence as cornea. Wear safety glasses.
3.3. Respiratory: May cause respiratory problems. This may damage throat and lungs and cause cough. Wear
respiratory mask.
4. First Aid Measures
4.1. Inhalation: May cause respiratory problem. Move to fresh air. If symptoms persist, call physician.
SAFETY DATA SHEET (SDS)
METYX
Glass Fiber Fabric
2
/5 FR-04-2/13.04.2015
4.2. Skin Contact: If skin irritation does occur, remove contaminated clothing and wash off plenty of water min.
15 minutes without rubbing. Use a mild soap if possible. If symptoms persist, call physician.
4.3. Eye Contact: Rinse immediately with plenty of water, also under the eyelids, for at least 15 minutes without
rubbing. If eye irritation persists, consult a specialist.
4.4. Ingestion: Gently wipe or rinse the inside of the mouth with water. Consult a physician if necessary.
4.5. Additional information: Mild hydrocortisone skin cream is helpful for skin irritation.
5. Fire Fighting Measures
5.1. Suitable Extinguishing Media: Water, carbon dioxide (CO2), foam, dry chemical. Extinguishing media for B
class fire may be used.
5.2. Special Protective Clothing: In case of big fires self-contained breathing apparatus must be used ad full
protective clothing must be worn.
5.3. Additional information: Only the packaging film, polyester yarn and glass sizing material are likely burn. Combustion
gases are basically carbon dioxide and water vapor. Formation of toxic gases is possible during heating or in case of fire.
There may be small quantities of carbon monoxide and other substances which make it necessary to use protective devices in
the event of a major fire. Fiberglass will not burn, but smoking of the product may occur at approximately 400 - 500 F
(approximately 200 - 260 C) due to decomposition of the surface binder.
Surface binders may decompose in a fire situation and release carbon monoxide, carbon dioxide and water. Additionally,
there are many chemicals that can evolve during any partial decomposition of chemical products. The amounts or identities
cannot be predicted and can differ in each situation.
6. Accidental Release Measures
6.1. Personal Precautions: Provide eyewash stations. Under normal industrial conditions, this product is not
flammable and has stability. See chapter 8.
6.2. Environmental Precautions: No special environmental precautions required.
6.3. Spill Cleanup Methods: NONE.
7. Handling & Storage
7.1. Usage Precautions: Wear appropriate personal protective equipment in case of direct contact with the product
(See section 8). Provide adequate ventilation. Prevent and/or minimize dust formation. Keep away heating
sources.
7.2. Storage Precautions: Keep product in its packaging until use to minimize potential dust generation. Store in
original package in a cool, dry place. Packing material must be prevented to damage during transporting and
carrying.
7.3. Special Usage: Vacuum clean, sweep or shovel carefully in order to prevent dust suspension.
SAFETY DATA SHEET (SDS)
METYX
Glass Fiber Fabric
3
/5 FR-04-2/13.04.2015
8. Exposure Control & Personal Protection
Continuous filament glass fibers are not respirable however certain mechanical processes might generate
airborne dust or fiber (See section 11).
8.1. Engineering Measures:
Occupational Exposure Limits (OEL)
Fiber Glass Continuous Filament (65997-17-3)
The American Conference of Governmental Hygienists has adopted a Threshold Limit Value (TLV) for fibrous
dust of 15mg/m (total) and 5mg/m (respirable). The Occupational Safety and Health Administration (OSHA)
does not prescribe a Permissible Exposure Limit (PEL) for fibrous glass but relies on the PEL-TWA s for
nuisance dust of 15mg/m (total) and 5mg/m (respirable).
Respirable fraction: 1 fiber/cc (related to respirable particulate with fiber-like dimensions (glass shards)
8.2. Respiratory Equipment: Provide adequate ventilation to ensure that the defined workplace exposure limit is
not exceeded. If use or application generates dust, use an appropriate respirator with a particulate filter.
8.3. Skin Protect: Skin irritation is known to occur chiefly at the pressure points such as around the neck, wrists,
and waist and between the fingers. Long-sleeved garments and long leggings are recommended to prevent irritation
Wear protective gloves (nitrile rubber, butyl rubber, PVC, Viton ).
8.4. Eye Protect: Wear safety glasses with side-shields.
8.5. Hygiene Considerations: Wash hands before breaks and immediately after handling the product
Avoid contact with skin, eyes and clothing
Avoid getting dust into boots and gloves through wrist bands and pant tucks
Remove and wash contaminated clothing before re-use
9. Physical & Chemical Specifications
9.1. Appear./Form/Odor: Solid, white, roll, odorless
9.2. Density: Glass: aprx. 2.6 g/cm
9.3. pH : not applicable
9.4. Viscosity: not applicable
9.5. Solubility: insoluble in water and oil
9.6. Vapor Pressure: not applicable
9.7. Flash Point: not applicable
9.8. Ignition Temp.: not applicable
9.9. Melting Point: Glass:~ 800-850 C,
9.10. Boiling Temp.: not applicable
9.11. Explosion Limits: not applicable
9.12. Thermal Decomposition: not applicable, see chapter 10
9.13. Other: Friction may cause static electricity
SAFETY DATA SHEET (SDS)
METYX
Glass Fiber Fabric
4
/5 FR-04-2/13.04.2015
10. Stability & Reactivity
10.1. Conditions to Avoid: High humidity and heat can affect product properties
10.2. Materials to Avoid: Moisture, strong oxidizing agents
10.3. Hazardous Decomposition Products: Long time high heat exposure can damage surface coating of product.
CO and NOx gasses can be released.
10.4 Possibility of hazardous reactions. Reacts with strong oxidizing agents, alkali, amines and acids
11. Toxicological Information
Glass fibers Short term effects:
Dusts and fibers may cause mechanical irritation to eyes and skin. The irritation disappears when the exposure
ceases. Mechanical irritation is not considered as a health hazard in the meaning of Regulation (EC) No 1272/2008
on hazardous substance. Continous filament glass fibers do not require a classification as an irritant (Xi) under the
Regulation (EC) No 1272/2008. Inhalation may cause coughing, nose and throat irritation and sneezing. High
exposures may cause difficult breathing, congestion and chest tightness.
Glass fibers Long term effects:
There are no known health effects from the long term use or contact with non-respirable continuous filament fibers.
Non-respirable fibers cannot reach the deep lung because they have a diameter of greater than 3.5 micrometers.
Fibers of this diameter cannot penetrate the narrow, bending passages of the human respiratory tract to reach the
lower regions of the lung and thus, have no possibility of causing serious pulmonary damage. Instead, they deposit
on the surfaces of the upper respiratory tract, nose, or pharynx. These fibers are then cleared through normal
physiological mechanisms.
Powder effects: When used and handled according to specifications, the product does not have any harmful effects
according to our experience and the information provided to us.
12. Ecological Information
12.1 Ecotoxicity: N/A
12.2 Mobility: N/A
12.3 Stability &Decomposition: N/A
12.4 Bioaccumulatetive: N/A
12.5 Other: N/A
13. Disposal Considerations
This product can be considered as immobile solid waste and disposed as solid waste. Glass fiber must be
destroyed depending on local regulations. The generation of waste should be avoided or minimised wherever possible.
Dispose of surplus and non-recyclable products via a licensed waste disposal contractor.
Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental
protection and waste disposal legislation and any regional local authority requirements.
SAFETY DATA SHEET (SDS)
METYX
Glass Fiber Fabric
5
/5 FR-04-2/13.04.2015
If glass fiber involves any resin to form a composite structure (cured or half cured), disposing of this material
must do considering disposal consideration of the resin.
Must not be disposed of together with household garbage. Do not allow product to reach sewage system.
14. Transport Information
Not classified as dangerous in the meaning of transport regulations.
Not classified as a hazardous material with respect to transportation regulations (ADR for road,
RID for rail, IMDG for sea and ICAO/IATA for air transport).
15. Regulatory Information
This product is not hazardous according to
Conforms to Regulation (EC) No. 1907/2006 (REACH), Annex II, as amended by Regulation (EU) No. 2015/830 -
United Kingdom (UK). Annex XIV - List of substances subject to authorisation No SVHC's normally expected above 0.1%
w/w
The international Agency for Research on Cancer (IARC) in June, 1987 and in October, 2001, categorized
continuous filament fiber glass as not classifiable with respect to human carcinogenicity (Group 3). The evidence
from human, as well as, animal studies was evaluated by IARC as insufficient to classify continuous filament fiber
glass as a confirmed, probable or even possible cancer causing material.
16. Other Information
Full text of abbreviated H Statements: Not applicable.
Full text of classifications [CLP/GHS]: Not applicable.
Abbreviations and acronyms : ATE = Acute Toxicity Estimate
CLP = Classification, Labelling and Packaging Regulation [Regulation (EC) No.
1272/2008]
DNEL = Derived No Effect Level
EUH statement = CLP-specific Hazard statement
PNEC = Predicted No Effect Concentration
RRN = REACH Registration Number
Rev date.26.04.2018
DISCLAIMER
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief
at the date of its publication. The information given is designed only as guidance for safe handling, use, processing,
storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The
information relates only to the specific material designated and may not be valid for such material used in
combination with any other materials or in any process, unless specified in the text. Users assume full
responsibility for applying the appropriate safety measures when the product used.
by | Sep 27, 2025
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
by | Sep 27, 2025
INDEX
27A5
27A50CP750
27A50PL100
27A55C0500
27A5CM0125
SAFETY DATA SHEET
Page 1 of 6 CORECELL
TM
FOAM
1 Product and Company Identification
Product identification: CORECELL
TM
Foam A,K,M,P,S,T series
Application of the material: Structural rigid foam panel
Supplier/Manufacturer: Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809
USA Tel: 401-396-5008
For additional information : Health, Safety and Environment department:
Email:
regulatory@gurit.com
Emergency phone number: 1-800-424-9300
Date of issue: 28/05/15
2 Hazards Identification
THIS PRODUCT WHEN SOLD IS NOT CLASSIFIED AS A HAZAR DOUS CHEMICAL PER OSHA HCS-2012.
However, when subject to machining operations under normal condition of use, the release of dust may pose a
combustible dust risk if work is not performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
– Prevent dust accumulations to minimize explosion hazard.
– Keep away from all ignition sources including heat, sparks and flame.
3 Composition/Information on Ingredients
Corecell
TM
is a structural expanded polymer product having some of the characteristics of SAN copolymer
CAS 9003-54-7. The chemicals listed below will be released when processing the product. Trace levels of
residual acrylonitrile monomers is also expected to be released in small amounts during processing operations.
Chemical name CAS number % concentration
Acetone 67-64-1 1 5 %
Hexane isomers 92112-69-1 1 5 %
SAFETY DATA SHEET
Page 2 of 6 CORECELL
TM
FOAM
6 Accidental Release Measures
Personal precautions, protective equipment and emergency procedures: No special measures required.
Clean up methods and materials: Vacuum or sweep up material.
5 Fire-Fighting Measures
Suitable extinguishing media: Water, foam, carbon dioxide or dry chemical fire extinguishers.
Specific hazards: Formation of toxic gases will occur during thermal decomposition or in case
of fire. Hazardous combustion products include Carbon monoxide, Carbon
dioxide, Nitrogen oxides, Hydrogen cyanide and Hydrogen bromide.
Protective equipment: Wear fully protective suit with self contained breathing apparatus (SCBA)
with a face-piece operated in positive pressure mode. Reduce direct exposure
to smoke and fumes.
4 First-Aid Measures
Eye contact: If dust particles become lodged in eyes, rinse immediately with plenty of water. If symptoms
persist, consult a physician.
Skin contact: No need for specific measures.
Ingestion: In case of persistent symptoms, consult a physician.
Inhalation: If affected by dust or vapors, remove individual to fresh air. If condition persists, obtain
medical attention.
Most important symptoms/effects: Upper respiratory system irritation.
Immediate medical attention and special treatment: No special requirements.
7 Handling and Storage
Handling: Machining operations which can produce dust should be properly fitted to a dust collection system.
Prevent formation of dust that could create explosive atmospheres.
Provide adequate general ventilation and local exhaust ventilation during machining and processing
operations to control airborne contaminant exposure.
Processing the product through heated equipment or tools could enhance the release of organic vapors.
Accumulation of static electricity charges may appear during machining operations or handling of the
material. Ensure all machining equipment are bonded and grounded to reduce static energy build-up.
Static electricity might give an unpleasant sensation but is not a possible source of ignition.
Storage: Protect from heat and open flames. This product is a combustible material and should be stored
according to the national or local Fire Code.
Trace levels of organic vapors may be released for a while after machining operations. Ensure good
mechanical ventilation for storage of large quantities of the processed product.
Date of issue: 28/05/15
SAFETY DATA SHEET
Page 3 of 6 CORECELL
TM
FOAM
8 Exposure Controls / Personal Protection
Exposure limits :
Ingredient name CAS# OSHA (PEL) ACGIH (TLV)
Acetone 67-64-1 1000 ppm (TWA)
500 ppm
(TWA)
;
750 ppm (STEL)
Hexane isomers 92112-69-1 –
500 ppm
(TWA)
;
1000 ppm (STEL)
Particulates Not Otherwise Regulated – 15 mg/m
3
(TWA) –
Note: Dust fraction size from machining operations will not constitute a respirable dust issue.
Engineering controls: Provide general and local exhaust ventilation to control airborne contaminant.
Personal protection equipments:
– Wear safety glasses/goggles.
– Wear general purpose gloves and protective work clothing.
– Wear approved NIOSH respirator with organic vapour cartridge if vapors are not adequately
controlled. Breathing protection recommended if excessive dust is generated.
General measures: Handle product with good industrial and safety practices.
Date of issue: 28/05/15
9 Physical and Chemical Properties
Physical state: Solid
Color: Yellow
Odor: Nearly odorless
Flash point: Not applicable
Melting point: Softening point 70
o
C – 120
o
C (158
o
F – 248
o
F)
Thermal degradation: >180
o
C (356
o
F)
Boiling point: Not applicable
Ignition temperature: Not available
Relative density: 0.05-0.5 g/cm
3
Vapor pressure: Not applicable
Solubility in water: Insoluble
Note: Items not included in this section are not available or not relevant to this product.
SAFETY DATA SHEET
Page 4 of 6 CORECELL
TM
FOAM
11 Toxicological Information
Toxicological data:
Substance LC50 (Inhalation Rat) LD50 (Oral Rat)
Acetone 21 000 ppm (8h) 5800 mg/kg
Route of exposure (when processing product): inhalation, eye contact.
Dust and vapors released when machining the product may cause irritation to upper
respiratory tract.
Dust and vapors released when machining the product may cause eye irritation.
Product is not expected to present harmful effects if swallowed.
Sensitization: No sensitizing effects known.
Chronic toxicity: No data available.
The product has not been tested as a whole for its possible chronic effects.
Additional information: It is recommended that pregnant or breastfeeding women should not be working in
areas where this product is processed.
Date of issue: 28/05/15
10 Stability and Reactivity
Chemical stability: This product is stable.
Conditions to avoid: Do not overheat to avoid thermal decomposition. Keep away from open flames.
Chemical reactivity: No relevant information available.
Possibility of hazardous reactions: No hazardous reactions known.
Incompatibility with other substances: Strong oxidizers, strong acids and bases will damage the product.
Hazardous decomposition products: Decomposition products include but are not limited to: Residual
monomers, Carbon monoxide, Carbon dioxide, Nitrogen oxides,
Hydrogen cyanide and Hydrogen bromide.
SAFETY DATA SHEET
Page 5 of 6 CORECELL
TM
FOAM
Regulatory status: This product is subject to hazardous classification only if machining or processing
the product is considered normal conditions of use. See safety label at the end of this
Safety Data Sheet as required by OSHA HCS.
TSCA (USA): All substances are listed.
California Prop. 65: This product contains trace quantities of a substance known to the State of California
to cause cancer: Acrylonitrile.
15 Regulatory Information
14 Transport Information
Regulatory status
(DOT; IMDG/IATA): Not regulated for transport.
13 Disposal Considerations
Waste disposal: Product is stable and may be disposed of in approved landfills. Toxic gases will be
generated if product is burned. Disposal of waste material should be done according to
applicable Federal and State regulations.
16 Other Information
References: 29CFR 1910.1200 OSHA Hazard Communication Standard (2012);
Notice to the reader:
To the best of our knowledge, the information contained herein is accurate at the date of its publication.
However, this shall not constitute a guarantee for any specific product features and shall not establish a
legally valid contractual relationship.
12 Ecological Information
Ecotoxicity data: No data available.
Persistence, biodegradability and mobility: No data available.
Date of issue: 28/05/15
SAFETY LABEL
Page 6 of 6 CORECELL
TM
FOAM
Corecell
TM
Foam
When this product is subject to processing methods under normal condition
of use, the release of dust may pose a combustible dust risk if work is not
performed under good industrial and safety practices.
WARNING!
May form combustible dust in the air.
Prevent dust accumulations to minimize explosion hazard.
Keep away from all ignition sources including heat, sparks and flame.
Gurit (USA) Inc.
115 Broadcommon Road
Bristol, Rhode Island 02809 USA
Tel: 401-396-5008
