by | Sep 27, 2025
TECHNICAL DATA SHEE T
VACFILM 800G
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VF800G_02.21_Issue1
VACFILM 800G
Vacuum bagging film
Ideally suited to aerospace applications
Features and Benefits
Highly conformable, transparent, co-polymer film
which will remain soft and pliable during cures up
to 177 C (351 F).
Suitable for use with complex tooling geometry.
Not recommended for use with polyester or
vinylester resin systems.
PROPERTIES
Maximum Use Temperature 204 C (400 F)
Color Green
Tensile strength at break (ASTM D882)
Transverse direction 90MPa 13053PSI
Machine direction 90MPa 13053PSI
Elongation at break (ASTM D882)
Transverse direction
Machine direction
500%
550%
Yield
17.54m /kg (50 m) 9.44yd /lb (0.001 )
11.76m /kg (75 m) 6.38yd /lb (0.002 )
8.77m /kg (100 m) 4.72yd /lb (0.004 )
AVAILABILITY
Thickness 50, 75 and 100 m 0.002, 0.003 and 0.004in
Roll weight Up to 150kg Up to 330lbs
Widths Up to 7m Up to 275in
Formats available Lay-flat tube, V sheet, sheet, gusseted, C-fold
STORAGE
Vacfilm 800G is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use
is therefore an important factor for successful performance. All nylon films absorb water. The higher the moisture content
the more flexible they become. Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product SDS for safe handling and personal protective equipment recomendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
STRETCH- VAC
TM
3000
Vacuum bagging film, ideally suited to aerospace applications.
Features and Benefits
Multi-layer vacuum baggng film produced using our
state of the art co- extrusion technology.
Suitable for high temperature autoclave curing of
aerospace composites, including BMI resins.
Soft and supple with unprecedented tensile strength
for added security.
Unique formulation less sensitive to low humidity
conditions than standard nylon films. SV 3000 is a
mono-nylon film.
PROPERTIES
Maximum use temperature 204
C 400
F
Color Pink
Density 1.14 g/cm
3
0.65oz/in
3
DSC medium 217
C 422.6 F
Tensile Strength at break (ASTM D882) 96.53 MPa 14,000 psi
Elongation at break (ASTM D882) 475%
Yield for 50 m (0.002 ) 17.4m
2
/kg 9.44 yd
2
/lb
Yield for 75 m (0.003 ) 11.6m
2
/kg 6.29yd
2
/lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003 inches
Roll weight Up to 45 kg Up to 100lbs.
Widths 4.06m (open) 160 inches (open)
Formats available Tube, sheet, V-sheet, gusseted and C-fold
STORAGE, HANDLING AND USE
Nylon based films are sensitive to humidity. A high humidity level will act as plasticizer, making the film more flexible and softer,
while a low humidity level will cause the film to become stiffer.
To preserve the integrity of the materials when stored in their original packaging, it is advisable not to stack more than two pallets.
Do not store rolls on their ends.
STORAGE (RECOMMENDED)
Store the film in a relative humidity (RH) from 25% to 60% and a temperature range of 15 to 40
C (59 to 104 F). Avoid stocking in
RH less than 25% and temperatures less than 10 C (50 F).
USAGE (RECOMMENDED)
If possible use the film in a RH ranging from 50% to 60% and a temperature range of 20 to 25 C (68 to 77 F).
If possible condition the film before handling for 48 hours in the recommended RH and temperature ranges.
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product SDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEE T
VACFILM 400Y
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VF400Y_02.21_Issue1
VACFILM 400Y
Vacuum bagging film
Ideally suited to marine and wind energy applications
Features and Benefits
Tough, high elongation elastomeric film, suitable for
de-bulking applications and oven curing of
composites up to temperatures of 150 C (302 F).
Due to the film s high elasticity, the necessity for
pleats is reduced in debulk operations.
Premium film for marine and wind energy applications.
Good release from sealant tape.
PROPERTIES
Maximum use
temperature
150 C (302 F)
Color Yellow
Tensile strength at break
(ASTM D882)
Transverse direction
Machine direction
40MPa
37MPa
5802PSI
5366PSI
Elongation at break
(ASTM D882)
Transverse direction
Machine direction
370%
360%
Yield
50 m (0.002in)
65 m (0.0025in)
75 m (0.003in)
19.12m /kg
14.71m /kg
12.74m /kg
10.37yd /lb
7.98yd /lb
6.91yd /lb
AVAILABILITY
Thickness 50, 65 and 75 m 0.002, 0.0025 and 0.003in
Roll weight Up to 45kg Up to 100lbs
Widths Up to 10.05m (open) Up to 394in (open)
Formats available Tube, sheet, V sheet, gusseted and C-fold
STORAGE
Vacfilm 400Y is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use is
therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
STRETCH- VAC
TM
3000
Vacuum bagging film, ideally suited to aerospace applications.
Features and Benefits
Multi-layer vacuum baggng film produced using our
state of the art co- extrusion technology.
Suitable for high temperature autoclave curing of
aerospace composites, including BMI resins.
Soft and supple with unprecedented tensile strength
for added security.
Unique formulation less sensitive to low humidity
conditions than standard nylon films. SV 3000 is a
mono-nylon film.
PROPERTIES
Maximum use temperature 204
C 400
F
Color Pink
Density 1.14 g/cm
3
0.65oz/in
3
DSC medium 217
C 422.6 F
Tensile Strength at break (ASTM D882) 96.53 MPa 14,000 psi
Elongation at break (ASTM D882) 475%
Yield for 50 m (0.002 ) 17.4m
2
/kg 9.44 yd
2
/lb
Yield for 75 m (0.003 ) 11.6m
2
/kg 6.29yd
2
/lb
AVAILABILITY
Thickness 50 and 75 m 0.002 and 0.003 inches
Roll weight Up to 45 kg Up to 100lbs.
Widths 4.06m (open) 160 inches (open)
Formats available Tube, sheet, V-sheet, gusseted and C-fold
STORAGE, HANDLING AND USE
Nylon based films are sensitive to humidity. A high humidity level will act as plasticizer, making the film more flexible and softer,
while a low humidity level will cause the film to become stiffer.
To preserve the integrity of the materials when stored in their original packaging, it is advisable not to stack more than two pallets.
Do not store rolls on their ends.
STORAGE (RECOMMENDED)
Store the film in a relative humidity (RH) from 25% to 60% and a temperature range of 15 to 40
C (59 to 104 F). Avoid stocking in
RH less than 25% and temperatures less than 10 C (50 F).
USAGE (RECOMMENDED)
If possible use the film in a RH ranging from 50% to 60% and a temperature range of 20 to 25 C (68 to 77 F).
If possible condition the film before handling for 48 hours in the recommended RH and temperature ranges.
TECHNICAL DATA SHEET
STRETCH- VAC
TM
3000
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS SV3000_0 2.21_Issue1
HEALTH & SAFETY
Please refer to the product SDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
li Huntington Beach Fax: + 1 714-899-8179 Website: wwwairtech.com
y ea CA92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 100, 100S, 100R, 100 ARMOR SLEEVE
High temperature autoclave/oven hoses
DESCRIPTION
Airflow 100 is a durable high temperature and high pressure autoclave hose. The hose construction consists of a
braided steel outer covering a PTFE inner tube supported with a flexible steel spring conduit. Its unique design
prevents collapse from vacuum or autoclave pressures.
Airflow 1008S has the same construction as the Airflow 100 with the addition of a steel outer protection coil.
Airflow 100R has the same construction as the Airflow 100 with the addition of a silicone rubber outer protective
sleeve.
Airflow 100 Armor Sleeve has the same construction as the Airflow 100 with an outer steel armor jacket.
BENEFITS
+ Safer vacuum for part curing with heavy duty metal hose construction.
+ More temperature resistance and longer in service life.
+ Different outer jackets for different use conditions.
Ml TECHNICAL DATA
Material type of inner tube PTFE
Material type of inner conduit Flexible steel
Material type of outer braid Steel
Material type of outer protection Flexible steel (100S) / Silicone rubber (100R)
End fitting 1/4 inch male NPT
Service temperature 260 C (500 F)
Max autoclave pressure 22 bar (320 psi)
lM SIZES
(9) Product Reference 9} Nominal Outer Hose Diameter Available Length
AIRFLOW 100 11.1. mm (7/16 inch) up to 30 m (100 feet)
AIRFLOW 100 S 11.1 mm (7/16 inch) up to 9 m (32 feet)
AIRFLOW 100 ARMOR SLEEVE 15.8 mm (5/8 inch) up to 22 m (75 feet)
AIRFLOW 100 R 15.8 mm (5/8 inch) up to 15 m (50 feet)
+ Though standard sizes are 3 meters (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
+ Other hose diameters and end fittings are available.
rear TO Fg Airflow 100
Wie Airflow 100S
aunannnarmnannorerecoTen ei Airflow 100
Armor Sleeve
OFT O]
sofia Airflow 100R ke
Airflow 100, 100R and 100 Armor Sleeve: % in. male NPT a ian
straight andor 90 end fitings on one or both ends.
Last updated : 2024-06-11
Catalog position : Vacuum valves and hoses
the conion or method endgame bred crotch Intestin neds atau reszenbay fhe paranormal”: Ach ema nc
cian buy enn and a np waar ng wie ion the ingd wane of earaba ano eter parce Te oman coaned her epeses wl papers Shine ed or
peer protein aniaeni proved ory Comeniene on) Tne ofcalnguoge sagan andte tel ona Caton Se
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
li Huntington Beach Fax: + 1 714-899-8179 Website: wwwairtech.com
y ea CA92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 100, 100S, 100R, 100 ARMOR SLEEVE
High temperature autoclave/oven hoses
DESCRIPTION
Airflow 100 is a durable high temperature and high pressure autoclave hose. The hose construction consists of a
braided steel outer covering a PTFE inner tube supported with a flexible steel spring conduit. Its unique design
prevents collapse from vacuum or autoclave pressures.
Airflow 1008S has the same construction as the Airflow 100 with the addition of a steel outer protection coil.
Airflow 100R has the same construction as the Airflow 100 with the addition of a silicone rubber outer protective
sleeve.
Airflow 100 Armor Sleeve has the same construction as the Airflow 100 with an outer steel armor jacket.
BENEFITS
+ Safer vacuum for part curing with heavy duty metal hose construction.
+ More temperature resistance and longer in service life.
+ Different outer jackets for different use conditions.
Ml TECHNICAL DATA
Material type of inner tube PTFE
Material type of inner conduit Flexible steel
Material type of outer braid Steel
Material type of outer protection Flexible steel (100S) / Silicone rubber (100R)
End fitting 1/4 inch male NPT
Service temperature 260 C (500 F)
Max autoclave pressure 22 bar (320 psi)
lM SIZES
(9) Product Reference 9} Nominal Outer Hose Diameter Available Length
AIRFLOW 100 11.1. mm (7/16 inch) up to 30 m (100 feet)
AIRFLOW 100 S 11.1 mm (7/16 inch) up to 9 m (32 feet)
AIRFLOW 100 ARMOR SLEEVE 15.8 mm (5/8 inch) up to 22 m (75 feet)
AIRFLOW 100 R 15.8 mm (5/8 inch) up to 15 m (50 feet)
+ Though standard sizes are 3 meters (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
+ Other hose diameters and end fittings are available.
rear TO Fg Airflow 100
Wie Airflow 100S
aunannnarmnannorerecoTen ei Airflow 100
Armor Sleeve
OFT O]
sofia Airflow 100R ke
Airflow 100, 100R and 100 Armor Sleeve: % in. male NPT a ian
straight andor 90 end fitings on one or both ends.
Last updated : 2024-06-11
Catalog position : Vacuum valves and hoses
the conion or method endgame bred crotch Intestin neds atau reszenbay fhe paranormal”: Ach ema nc
cian buy enn and a np waar ng wie ion the ingd wane of earaba ano eter parce Te oman coaned her epeses wl papers Shine ed or
peer protein aniaeni proved ory Comeniene on) Tne ofcalnguoge sagan andte tel ona Caton Se
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
fF = CA 92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 100, 100S, 100R, 100 ARMOR SLEEVE
High temperature autoclave/oven hoses
lM DESCRIPTION
Airflow 100 is a durable high temperature and high pressure autoclave hose. The hose construction consists of a
braided steel outer covering a PTFE inner tube supported with a flexible steel spring conduit. Its unique design
prevents collapse from vacuum or autoclave pressures.
Airflow 100S has the same construction as the Airflow 100 with the addition of a steel outer protection coil.
Airflow 100R has the same construction as the Airflow 100 with the addition of a silicone rubber outer protective
sleeve.
Airflow 100 Armor Sleeve has the same construction as the Airflow 100 with an outer steel armor jacket.
M@ BENEFITS
+ Safer vacuum for part curing with heavy duty metal hose construction.
+ More temperature resistance and longer in service life.
+ Different outer jackets for different use conditions.
@ TECHNICAL DATA
Material type of inner tube PTFE
Material type of inner conduit Flexible steel
Material type of outer braid Steel
Material type of outer protection Flexible steel (100S) / Silicone rubber (100R)
End fitting 1/4 inch male NPT
Service temperature 260 C (500 F)
Max autoclave pressure 22 bar (320 psi)
@ SIZES
Product Reference Nominal Outer Hose Diameter Available Length
AIRFLOW 100 11.1 mm (7/16 inch) up to 30 m (100 feet)
AIRFLOW 100 S 11.1 mm (7/16 inch) up to 9 m (32 feet)
AIRFLOW 100 ARMOR SLEEVE 15.8 mm (5/8 inch) up to 22 m (75 feet)
AIRFLOW 100 R 15.8 mm (5/8 inch) up to 15 m (50 feet)
+ Though standard sizes are 3 meters (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
+ Other hose diameters and end fittings are available.
Feiner ED Airflow 100
Airflow 100S
ch ~ Airflow 100
Armor Sleeve
_ Eee]
=- Airflow 100R ere
aes
iow 100, 100R and 100 Armor Sleeve: %in. male NPT ie
straight andlor 90 end fitings on one or both ends. =>
Last updated : 2024-06-11 y,
Catalog position : Vacuum valves and hoses A
ste conditions creat ue nding sarge beyond ot cota itech trator does ese pony for the pevonnnce fhe for ry arr. The mates sols Artech inten ne A
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
fF = CA 92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 100, 100S, 100R, 100 ARMOR SLEEVE
High temperature autoclave/oven hoses
lM DESCRIPTION
Airflow 100 is a durable high temperature and high pressure autoclave hose. The hose construction consists of a
braided steel outer covering a PTFE inner tube supported with a flexible steel spring conduit. Its unique design
prevents collapse from vacuum or autoclave pressures.
Airflow 100S has the same construction as the Airflow 100 with the addition of a steel outer protection coil.
Airflow 100R has the same construction as the Airflow 100 with the addition of a silicone rubber outer protective
sleeve.
Airflow 100 Armor Sleeve has the same construction as the Airflow 100 with an outer steel armor jacket.
M@ BENEFITS
+ Safer vacuum for part curing with heavy duty metal hose construction.
+ More temperature resistance and longer in service life.
+ Different outer jackets for different use conditions.
@ TECHNICAL DATA
Material type of inner tube PTFE
Material type of inner conduit Flexible steel
Material type of outer braid Steel
Material type of outer protection Flexible steel (100S) / Silicone rubber (100R)
End fitting 1/4 inch male NPT
Service temperature 260 C (500 F)
Max autoclave pressure 22 bar (320 psi)
@ SIZES
Product Reference Nominal Outer Hose Diameter Available Length
AIRFLOW 100 11.1 mm (7/16 inch) up to 30 m (100 feet)
AIRFLOW 100 S 11.1 mm (7/16 inch) up to 9 m (32 feet)
AIRFLOW 100 ARMOR SLEEVE 15.8 mm (5/8 inch) up to 22 m (75 feet)
AIRFLOW 100 R 15.8 mm (5/8 inch) up to 15 m (50 feet)
+ Though standard sizes are 3 meters (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
+ Other hose diameters and end fittings are available.
Feiner ED Airflow 100
on Airflow 100S
ch ~ Airflow 100
Armor Sleeve
_ Eee]
=- Airflow 100R ere
mates
iow 100, 100R and 100 Armor Sleeve: %in. male NPT ie
straight andlor 90 end fitings on one or both ends. =>
Last updated : 2024-06-11 y,
Catalog position : Vacuum valves and hoses A
ste conditions creat ue nding sarge beyond ot cota itech trator does ese pony for the pevonnnce fhe for ry arr. The mates sols Artech inten ne A
by | Sep 27, 2025
5700 Skylab Road Phone: +1 714-899-8100 E-mail: airtech@airtech.com
iT Huntington Beach Fax: + 1 714-899-8179 Website: www.airtech.com
fF = CA 92647 USA
INTERNATIONAL INC.
Data Sheet AIRFLOW 100, 100S, 100R, 100 ARMOR SLEEVE
High temperature autoclave/oven hoses
lM DESCRIPTION
Airflow 100 is a durable high temperature and high pressure autoclave hose. The hose construction consists of a
braided steel outer covering a PTFE inner tube supported with a flexible steel spring conduit. Its unique design
prevents collapse from vacuum or autoclave pressures.
Airflow 100S has the same construction as the Airflow 100 with the addition of a steel outer protection coil.
Airflow 100R has the same construction as the Airflow 100 with the addition of a silicone rubber outer protective
sleeve.
Airflow 100 Armor Sleeve has the same construction as the Airflow 100 with an outer steel armor jacket.
M@ BENEFITS
+ Safer vacuum for part curing with heavy duty metal hose construction.
+ More temperature resistance and longer in service life.
+ Different outer jackets for different use conditions.
@ TECHNICAL DATA
Material type of inner tube PTFE
Material type of inner conduit Flexible steel
Material type of outer braid Steel
Material type of outer protection Flexible steel (100S) / Silicone rubber (100R)
End fitting 1/4 inch male NPT
Service temperature 260 C (500 F)
Max autoclave pressure 22 bar (320 psi)
@ SIZES
Product Reference Nominal Outer Hose Diameter Available Length
AIRFLOW 100 11.1 mm (7/16 inch) up to 30 m (100 feet)
AIRFLOW 100 S 11.1 mm (7/16 inch) up to 9 m (32 feet)
AIRFLOW 100 ARMOR SLEEVE 15.8 mm (5/8 inch) up to 22 m (75 feet)
AIRFLOW 100 R 15.8 mm (5/8 inch) up to 15 m (50 feet)
+ Though standard sizes are 3 meters (10 feet), hose lengths can be customized to meet your specific
requirements, contact Airtech for more information.
+ Other hose diameters and end fittings are available.
Feiner ED Airflow 100
Airflow 100S
ch ~ Airflow 100
Armor Sleeve
_ Eee]
=- Airflow 100R ere
aes
iow 100, 100R and 100 Armor Sleeve: %in. male NPT ie
straight andlor 90 end fitings on one or both ends. =>
Last updated : 2024-06-11 y,
Catalog position : Vacuum valves and hoses A
ste conditions creat ue nding sarge beyond ot cota itech trator does ese pony for the pevonnnce fhe for ry arr. The mates sols Artech inten ne A
by | Sep 27, 2025
TECHNICAL DATA SHEE T
VACFILM 465B
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VF465B_02.21_Issue1
VACFILM 465B
Vacuum bagging film
Ideally suited to wind energy applications
Features and Benefits
High strength, high elongation yet stiff film.
Multi-layer, co- extruded film with a
nylon/polyethylene construction which exhibits
excellent resistance to polyester, vinylester and
epoxy resins.
Ideally suited for use with medium temperature epoxy
prepregs.
Ideal for use in the production in large components
such as wind energy structures.
PROPERTIES
Maximum use
temperature
165 C (329 F)
Colour Blue
Tensile strength at break
(ASTM D882)
Transverse direction
Machine direction
80MPa
80MPa
10878PSI
10878PSI
Elongation at break
(ASTM D882)
Transverse direction
Machine direction
400%
450%
Yield 15.38m /kg 8.34yd /lb
AVAILABILITY
Thickness 50 m / 55 m / 75 m 0.002in / 0.0023im / 0.003in
Roll weight Up to 45kg Up to 100lbs
Widths Up to 7.5m (open) Up to 295in (open)
Formats available Sheet, V-sheet and tube
STORAGE
Vacfilm 465B is a hydrophilic material. Moisture and water act as plasticizers. The level of moisture content at time of use is
therefore an important factor for successful performance. The higher the moisture content the more flexible they become.
Conversely at lower moisture levels flexibility is limited.
Do not store rolls vertically on their ends.
TECHNICAL DATA SHEE T
VACFILM 465B
VACUUM BAGGING FILM
Aerovac
955-10 National Parkway
Schaumburg, IL 60 173
USA
TDS VF465B_02.21_Issue1
HEALTH & SAFETY
Please refer to the product MSDS for safe handling, personal protective equipment recommendations and disposal
considerations.
DISCLAIMER: The data and information provided in this document have been obtained from carefully controlled samples and are considered to be
representative of the product described. Aerovac does not express or imply any guarantee or warranty of any kind including, but not limited to, the accuracy, the
completeness or the relevance of the data and information set out herein. Because the properties of this product can be significantly affected by the fabrication
and testing techniques employed, and since Aerovac does not control the conditions under which its products are tested and used, Aerovac cannot guarantee
the properties provided will be obtained with other processes and equipment. No guarantee or warranty is provided if the product is adapted for a s pecific use or
purpose. Aerovac declines any liability with respect to the use made by any third party of the data and information contained herein. Aerovac has the right to
change any data or information when deemed appropriate. All trademarks are the property of their respective owners. 2021 , Aerovac. All rights reserved.
