application/pdf | Revchem Composites

10A107_SDS.pdf

by | Sep 27, 2025

ThermoFisher
SCIENTIFIC
SAFETY DATA SHEET
Creation Date 22-Sep-2009 Revision Date 17-Jan-2018 Revision Number 5
1 Identification Se en
Product Name 2,4-Pentanedione
Cat No. : A25-500
CAS-No 123-54-6
Synonyms Acetylacetone
Recommended Use Laboratory chemicals.
Uses advised against Not for food, drug, pesticide or biocidal product use
Details of the supplier of the safety data sheet
Company
Fisher Scientific
One Reagent Lane
Fair Lawn, NJ 07410
Tel: (201) 796-7100
Emergency Telephone Number
CHEMTREC , Inside the USA: 800-424-9300
CHEMTRECS, Outside the USA: 001-703-527-3887
2. Hazard(s) identification
Classification
This chemical is considered hazardous by the 2012 OSHA Hazard Communication Standard (29 CFR 1910.1200)
Flammable liquids Category 3
Acute oral toxicity Category 4
Acute dermal toxicity Category 3
Acute Inhalation Toxicity – Vapors Category 3
Label Elements
Signal Word
Danger
Hazard Statements
Flammable liquid and vapor
Harmful if swallowed
Toxic in contact with skin
Toxic if inhaled
Page 1/8

123M00512_SDS.pdf

by | Sep 27, 2025

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 1of 7

Material Safety Data Sheet

Copyright, 2010, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly
utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is
obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit
thereon.
SECTION 1: PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME: 3M Abrasive Product, 750U, 751U
MANUFACTURER: 3M
DIVISION: Abrasives Systems Division
ADDRESS: 3M Center
St. Paul, MN 55144-1000
EMERGENCY PHONE: 1-800-364-3577 or (651) 737-6501 (24 hours)
Issue Date: 03/29/10
Supercedes Date: 03/01/10
Document Group:08-9059-0
Product Use:
Intended Use: Abrasive Product
SECTION 2: INGREDIENTS
Ingredient C.A.S. No. % by Wt
Hookit Backing None 25 -55
Aluminum Oxide Mineral 1344-28-1 15 -40
Cured Resin Mixture 10 -20
Cubitron Mineral 66402-68-4 3 -15
Filler 1317-65-3 4 -10
SECTION 3: HAZARDS IDENTIFICATION
3.1 EMERGENCY OVERVIEW
Odor, Color, Grade: Solid abrasive product, no odor.
General Physical Form: Solid
Immediate health, physical, and environmental hazards: his document covers only the 3M product. For
complete assessment, when determining the degree of hazard, the material being abraded must also be considered.

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 2of 7
3.2 POTENTIAL HEALTH EFFECTS
Eye Contact:
Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion.
Dust created by cutting, grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling,
pain, tearing, and blurred or hazy vision.
Skin Contact:
Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching.
Inhalation:
Dust from cutting, grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough,
sneezing, nasal discharge, headache, hoarseness, and nose and throat pain.
Ingestion:
No health effects are expected.

SECTION 4: FIRST AID MEASURES
4.1 FIRST AID PROCEDURES
he following first aid recommendations are based on an assumption that appropriate personal and industrial hygiene practices are
followed.
Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention.
Skin Contact: Wash affected area with soap and water. If signs/symptoms develop, get medical attention.
Inhalation: If signs/symptoms develop, remove person to fresh air. If signs/symptoms persist, get medical attention.
If Swallowed: No need for first aid is anticipated.
SECTION 5: FIRE FIGHTING MEASURES
5.1 FLAMMABLE PROPERTIES
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 3of 7
5.2 EXTINGUISHING MEDIA
Ordinarycombustible material. Use fire extinguishers with class A extinguishing agents (e.g., water, foam).
5.3 PROTECTION OF FIRE FIGHTERS
Special Fire Fighting Procedures: Wear full protective equipment (Bunker Gear) and a self-contained breathing apparatus
(SCBA).
Unusual Fire and Explosion Hazards: Not applicable. None inherent in this product.
Note: See STABILITY AND REACTIVITY (SECTION 10) for hazardous combustion and thermal decomposition
information.
SECTION 6: ACCIDENTAL RELEASE MEASURES
Accidental Release Measures:
Not applicable.
In the event of a release of this material, the user should determine if therelease qualifies as reportable according to
local, state, and federal regulations.
SECTION 7: HANDLING AND STORAGE
7.1 HANDLING
For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can
break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace
if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations.
Sparks and particles flying from the product during sanding or grinding can cause injury and fire.
7.2 STORAGE
Store in a cool, dry place.
SECTION 8: EXPOSURE CONTROLS/PERSONAL PROTECTION
8.1 ENGINEERING CONTROLS
Use with appropriate local exhaust ventilation. Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use
general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below Occupational Exposure Limits
and/or control dust, fume, or airborne particles. If ventilation is not adequate, use respiratory protection equipment.
8.2 PERSONAL PROTECTIVE EQUIPMENT (PPE)
8.2.1 Eye/Face Protection
Avoid eye contact. To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or
grinding operations or when near such operations.
he following eye protection(s) are recommended: Safety Glasses with side shields
.

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 4of 7
8.2.2 Skin Protection
Avoid skin contact. Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from
grinding or sanding.

8.2.3 Respiratory Protection
Avoid breathing of dust created by sanding, grinding or machining. Assess exposure concentrations of all materials involved in the
work process. Consider material being abraded when determining the appropriate resipratory protection. Select and use appropriate
respirators to prevent inhalation overexposure.
Select one of the following NIOSH approved respirators based on airborne concentration of contaminants and in accordance with
OSHA regulations: Half facepiece or fullface air-purifying respirator with N95 particulate filters
. Consult the current 3M Respiratory Selection Guide for additional information or call 1-800-243-4630 for 3M technical assistance.
8.2.4 Prevention of Swallowing
Not an expected route of exposure. Wash hands after handlingand before eating.
8.3 EXPOSURE GUIDELINES
IngredientAuthorityType Limit Additional Information
Aluminum Oxide Mineral CMRG TWA 1 fiber/cc
Aluminum Oxide Mineral OSHA TWA, respirable
fraction
5 mg/m3
Aluminum Oxide Mineral OSHA TWA, as total dust15 mg/m3
Filler OSHA TWA, respirable
fraction
5 mg/m3
Filler OSHA TWA, as total dust15 mg/m3
SOURCE OF EXPOSURE LIMI DATA:
ACGIH: American Conference of Governmental Industrial Hygienists
CMRG: Chemical Manufacturer Recommended Guideline
OSHA: Occupational Safety and Health Administration
AIHA: American Industrial Hygiene Association Workplace Environmental Exposure Level (WEEL)

SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES
Odor, Color, Grade: Solid abrasive product, no odor.
General Physical Form: Solid
Autoignition temperature Not Applicable
Flash Point Not Applicable
Flammable Limits -LEL Not Applicable
Flammable Limits -UEL Not Applicable
Boiling point Not Applicable
Vapor Density Not Applicable
Vapor Pressure Not Applicable
Specific Gravity No Data Available
pH Not Applicable
Melting point Not Applicable

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 5of 7
Solubility In Water Not Applicable
Evaporation rate Not Applicable
Volatile Organic Compounds Not Applicable
Kow -Oct/Water partition coef Not Applicable
Percent volatile Not Applicable
VOC Less H2O & Exempt Solvents Not Applicable
SECTION 10: STABILITY AND REACTIVITY
Stability:Stable.
Materials and Conditions to Avoid:
10.1 Conditions to avoid
None known

10.2 Materials to avoid
None known
Hazardous Polymerization: Hazardous polymerization will not occur.

Hazardous Decomposition or By-Products
Substance Condition
Carbon monoxide During Combustion
Carbon dioxide During Combustion

Hazardous Decomposition: Under recommended usage conditions, hazardous decomposition products are not expected. Hazardous
decomposition products may occur as a result of oxidation, heating, or reaction with another material.

SECTION 11: TOXICOLOGICAL INFORMATION

Please contact the address listed on the first page of the MSDS for Toxicological Information on this material and/or its
components.
SECTION 12: ECOLOGICAL INFORMATION
ECOTOXICOLOGICAL INFORMATION
Not determined.
CHEMICAL FATE INFORMATION
Not determined.

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 6of 7
SECTION 13: DISPOSAL CONSIDERATIONS
Waste Disposal Method: he substrate that was abraded must be considered as a factor in the disposal method for this product.
Dispose of waste product in a sanitary landfill. As a disposal alternative, incinerate in an industrial or commercial facility in the
presence of a combustible material.
EPA Hazardous Waste Number (RCRA):Not regulated
Since regulations vary, consult applicable regulations or authorities before disposal.
SECTION 14:TRANSPORT INFORMATION
Not regulated per U.S. DOT, IATA or IMO.
These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for
complying with all applicable laws and regulations, including proper transportation classification and packaging.3M s
transportation classifications are based on product formulation, packaging, 3M policies and 3M s understanding of applicable
current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to
transportation classification and notthe packaging, labeling, or marking requirements.The original 3M package is certified
for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory
requirements.
SECTION 15: REGULATORY INFORMATION
US FEDERAL REGULATIONS
Contact 3M for more information.
311/312 Hazard Categories:
Fire Hazard -No Pressure Hazard -No Reactivity Hazard -No Immediate Hazard -Yes Delayed Hazard -Yes

STATE REGULATIONS
Contact 3M for more information.
CHEMICAL INVENTORIES
his product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements.
Contact 3M for more information.

MATERIAL SAFETY DATA SHEET 3M Abrasive Product, 750U, 751U 03/29/10
_________________________________________________________________________________________________
Page 7of 7

INTERNATIONAL REGULATIONS
Contact 3M for more information.
WHMIS: Hazardous

This MSDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200.
SECTION 16: OTHER INFORMATION
NFPA Hazard Classification
Health: 1 Flammability: 1 Reactivity: 0 Special Hazards: None

National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are
presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the
inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to
be generated in significant quantities.

Reason for Reissue: he MSDS has been revised because 3M has adopted the 16-section ANSI/ISO format. he potential hazards
of the product have not changed. We encourage you to reread the MSDS and review the information.
Revision Changes:
Section 8: Eye/face protection information was modified.
Section 8: Respiratory protection -recommended respirators information was modified.
Section 10: Materials to avoid physical property was modified.
Section 10: Conditions to avoid physical property was modified.
DISCLAIMER: he information in this Material Safety Data Sheet (MSDS) is believed to be correct as of the date issued. 3M
MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BU NO LIMITED TO, ANY IMPLIED WARRANTY
OF MERCHANTABILITY O R FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF
TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of
use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely
within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a
particular purpose and suitable for user’s method of use or application.
3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may
have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy.
In addition, information obtained from a database may not be as current as the information in the MSDS available directly from 3M.

3M MSDSs are available at www.3M.com

10A106_SDS.pdf

by | Sep 27, 2025

Safety Data Sheet
according to 29CFR1910/1200 and GHS Rev. 3
Effective date : 10.24.2014 Page 1 of 7
Acetone Reagent Grade
SECTION 1: Identification of the substance/mixture and of the supplier
Product name : Acetone Reagent Grade
Manufacturer/Supplier Trade name:
Manufacturer/Supplier Article number: S25120B
Recommended uses of the product and uses restrictions on use:
Manufacturer Details:
AquaPhoenix Scientific
9 Barnhart Drive, Hanover, PA 17331
Supplier Details:
Fisher Science Education
15 Jet View Drive, Rochester, NY 14624
Emergency telephone number:
Fisher Science Education Emergency Telephone No.: 800-535-5053
SECTION 2 : Hazards identification
Classification of the substance or mixture:
Flammable
Flammable liquids, category 2
Irritant
Eye irritation, category 2A
Specific target organ toxicity following single exposure, category 3
Flam. Liq. 2
Eye Irrit. 2A
STOT SE3
Signal word :Danger
Hazard statements:
Highly flammable liquid and vapour
Causes serious eye irritation
May cause drowsiness or dizziness
Precautionary statements:
If medical advice is needed, have product container or label at hand
Keep out of reach of children
Read label before use
Keep away from heat/sparks/open flames/hot surfaces. No smoking
Wear protective gloves/protective clothing/eye protection/face protection
Keep container tightly closed
Ground/bond container and receiving equipment
Use explosion-proof electrical/ventilating/light/equipment
Use only non-sparking tools
Take precautionary measures against static discharge
Avoid breathing dust/fume/gas/mist/vapours/spray
Created by Global Safety Management, Inc. -Tel: 1-813-435-5161 – www.gsmsds.com

10A104_SDS.pdf

by | Sep 27, 2025

SAFETY DATA SHEET
SDS Distribution: The information in this document
should be made available to all who may handle the
product.
Product ID 20-80 Blend
20-80 Blend
Page 1 of 10 www.aglayne.com

SECTION 2) HAZARDS IDENTIFICATION
Classification
Carcinogenicity – Category 1A
Eye Irritation – Category 2A
Flammable Liquids – Category 2
Germ Cell Mutagenicity – Category 1B
Skin Irritation – Category 2
Specific Target Organ Toxicity -Single Exposure (Narcotic Effects) – Category 3
Pictograms
Signal Word
Danger
Hazardous Statements – Physical
Highly flammable liquid and vapor
Hazardous Statements – Health
May cause cancer.
Causes serious eye irritation
May cause genetic defects.
Causes skin irritation
May cause drowsiness or dizziness
Precautionary Statements – General
If medical advice is needed, have product container or label at hand.
Keep out of reach of children.
SAFETY DATA SHEET
May 04, 2021
A. G. Layne, Inc.
4578 Brazil Street Los Angeles, CA, US, 90039
Manufacturer’s Name:
Revision Date:
Address:
SECTION 1) CHEMICAL PRODUCT AND MANUFACTURER’S IDENTIFICATION
Version: 1.0
Date Printed: May 04, 2021
Supersedes Date: N.A.
Product ID: 20-80 Blend
Product Name: 20-80 Blend
Emergency Phone:
Information Phone Number:
CHEMTREC US : 1-800-424-9300, INTERNATIONAL CALLS : 1-703-527-3887
323-245-2345
Fax:
Product/Recommended Uses: Industrial solvent
20-80 Blend
Page 2 of 10 www.aglayne.com

Read label before use.
Precautionary Statements – Prevention
Obtain special instructions before use.
Do not handle until all safety precautions have been read and understood.
Wear protective gloves/protective clothing/eye protection/face protection.
Wash with soap and water thoroughly after handling.
Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
Keep container tightly closed.
Ground/bond container and receiving equipment.
Use explosion-proof electrical/ventilating/lighting equipment.
Use only non-sparking tools.
Take action to prevent static discharges.
Avoid breathing dust/fume/gas/mist/vapors/spray.
Use only outdoors or in a well-ventilated area.
Precautionary Statements – Response
IF exposed or concerned: Get medical advice/attention.
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
If eye irritation persists: Get medical advice/attention.
IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse with water or shower.
In case of fire: Use DRY chemical, alcohol- resistant foam, water spray/fog or carbon-dioxide to extinguish.
IF ON SKIN: Wash with plenty of water.
Specific treatment (see First-aid on this label).
If skin irritation occurs: Get medical advice/attention.
Take off contaminated clothing. And wash it before reuse.
IF INHALED: Remove person to fresh air and keep comfortable for breathing.
Call a POISON CENTER/doctor if you feel unwell.
Precautionary Statements – Storage
Store locked up.
Store in a well-ventilated place. Keep cool.
Store in a well-ventilated place. Store locked up.
Precautionary Statements – Disposal
Dispose of contents/container to disposal recycling center.
Waste management should be in full compliance with federal, state and local laws.
Hazards Not Otherwise Classified (HNOC)
None
SECTION 4) FIRST-AID MEASURES
CAS Chemical Name % By Weight
0000067-64-1 ACETONE 61.780% – 92.670%
0000079-20-9 METHYL ACETATE 18.220% – 27.330%
0000071-43-2 BENZENE 0 – 0.001 %
Specific chemical identity and/or exact percentage (concentration) of the composition has been withheld to protect confidentiality.
SECTION 3) COMPOSITION, INFORMATION ON INGREDIENTS
20-80 Blend
Page 3 of 10 www.aglayne.com

Inhalation
Remove source of exposure or move person to fresh air and keep comfortable for breathing. If victim is not breathing, call 911 and
administer CPR as directed.
Eliminate all ignition sources if safe to do so.
Skin Contact
Rinse/wash with lukewarm, gently flowing water (and mild soap) for 15-20 minutes or until product is removed. If skin irritation occurs or
you feel unwell: Get medical advice/attention.
Eye Contact
Remove source of exposure or move person to fresh air. Rinse eyes cautiously with lukewarm, gently flowing water for 15-20 minutes,
while holding the eyelids open. Remove contact lenses, if present and easy to do. Continue rinsing. Take care not to rinse contaminated
water into the unaffected eye or onto the face. Get immidiate medical attention.
Ingestion
Immediately call 911 POISON CENTER/doctor/.Immediately transport to the nearest medical facility for treatment.Do NOT induce
vomiting. If vomiting occurs naturally, lie on your side, in the recovery position.
Most important symptoms and effects, both acute and delayed
No data available.
Indication of any immediate medical attention and special treatment needed
No data available.
SECTION 5) FIRE-FIGHTING MEASURES
Suitable Extinguishing Media
Dry chemical, foam, carbon dioxide or fog is recommended. Water spray is recommended to cool or protect exposed materials or
structures. Carbon dioxide can displace oxygen. Use caution when applying carbon dioxide in confined spaces. Simultaneous use of
foam and water on the same surface is to be avoided as water destroys the foam. Sand or earth may be used for small fires only.
Unsuitable Extinguishing Media
No data available.
Specific Hazards in Case of Fire
No data available.
Fire-fighting Procedures
Isolate immediate hazard area and keep unauthorized personnel out. Stop spill/release if it can be done safely. Move undamaged
containers from immediate hazard area if it can be done safely. Water spray may be useful in minimizing or dispersing vapors and to
protect personnel.
Dispose of fire debris and contaminated extinguishing water in accordance with official regulations.
Special Protective Actions
Wear protective pressure self-contained breathing apparatus (SCBA) and full turnout gear.
SECTION 6) ACCIDENTAL RELEASE MEASURES
Emergency Procedure
ELIMINATE all ignition sources (no smoking, flares, sparks or flames in immediate area).
RELEASE CAN CAUSE FIRE/EXPLOSION. LIQUIDS/VAPORS MAY IGNITE.
Do not touch or walk through spilled material.
Isolate hazard area and keep unnecessary people away. Remove all possible sources of ignition in the surrounding area. Notify
authorities if any exposure to the general public or the environment occurs or is likely to occur.
If spilled material is cleaned up using a regulated solvent, the resulting waste mixture may be regulated.
Recommended Equipment
Positive pressure, full-facepiece self-contained breathing apparatus (SCBA), or positive pressure supplied air respirator with escape
SCBA (NIOSH approved).
Personal Precautions
Avoid breathing vapor. Avoid contact with skin, eye or clothing. ELIMINATE all ignition sources (no smoking, flares, sparks or flames in
immediate area). Use explosive proof equipment. Avoid inhalation of dust and contact with skin and eyes. Do not touch damaged
containers or spilled materials unless wearing appropriate protective clothing.
20-80 Blend
Page 4 of 10 www.aglayne.com

Environmental Precautions
Stop spill/release if it can be done safely. Prevent spilled material from entering sewers, storm drains, other unauthorized drainage
systems and natural waterways by using sand, earth, or other appropriate barriers.
Methods and Materials for Containment and Cleaning up
Sand, clay and absorbent socks can be used to contain a spill.
SECTION 7) HANDLING AND STORAGE
General
Wash hands after use.
Do not get in eyes, on skin or on clothing.
Do not breathe vapors or mists.
Use good personal hygiene practices.
Eating, drinking and smoking in work areas is prohibited.
Remove contaminated clothing and protective equipment before entering eating areas.
Eyewash stations and showers should be available in areas where this material is used and stored.
Ventilation Requirements
Use only with adequate ventilation to control air contaminants to their exposure limits. The use of local ventilation is recommended to
control emissions near the source.
Storage Room Requirements
Keep container(s) tightly closed and properly labeled. Store in cool, dry, well-ventilated areas away from heat, direct sunlight, strong
oxidizers and any incompatibilities. Store in approved containers and protect against physical damage. Keep containers securely sealed
when not in use. Indoor storage should meet OSHA standards and appropriate fire codes. Containers that have been opened must be
carefully resealed to prevent leakage. Empty container retain residue and may be dangerous.
Use non-sparking ventilation systems, approved explosion-proof equipment and intrinsically safe electrical systems in areas where this
product is used and stored.
Ground and bond containers and receiving equipment. Avoid static electricity by grounding.
Electrostatic charges may be generated during pumping. Keep away from aerosols, flammables, oxidizing agents, corrosives and from
other flammable products.
SECTION 8) EXPOSURE CONTROLS, PERSONAL PROTECTION
Eye Protection
Wear eye protection with side shields or goggles. Wear indirect-vent, impact and splash resistant goggles when working with liquids. If
additional protection is needed for entire face, use in combination with a face shield.
Skin Protection
Use of gloves approved to relevant standards made from the following materials may provide suitable chemical protection: PVC,
neoprene or nitrile rubber gloves. Suitability and durability of a glove is dependent on usage, e.g. frequency and duration of contact,
chemical resistance of glove material, glove thickness, dexterity. Always seek advice from glove suppliers. Contaminated gloves should
be replaced. Use of an apron and over- boots of chemically impervious materials such as neoprene or nitrile rubber is recommended to
avoid skin sensitization. The type of protective equipment must be selected according to the concentration and amount of the dangerous
substance at the specific workplace. Launder soiled clothes or properly disposed of contaminated material, which cannot be
decontaminated.
Respiratory Protection
If engineering controls do not maintain airborne concentrations to a level which is adequate to protect worker, a respiratory protection
program that meets or is equivalent to OSHA 29 CFR 1910.134 and ANSI Z88.2 should be followed. Check with respiratory protective
equipment suppliers.
Appropriate Engineering Controls
Provide exhaust ventilation or other engineering controls to keep the airborne concentrations of vapors below their respective threshold
limit value.
Chemical
Name
OSHA TWA
(ppm)
OSHA TWA
(mg/m3)
OSHA STEL
(ppm)
OSHA STEL
(mg/m3)
OSHA Tables
(Z1, Z2, Z3)
OSHA
Carcinogen
OSHA Skin
designation
NIOSH TWA
(ppm)
ACETONE 1000 2400 1 250
BENZENE 1 (a) / 25ceiling 50(a)/
10minutes.
1 1 0.1c
METHYL
ACETATE
200 610 1 200
20-80 Blend
Page 5 of 10 www.aglayne.com

Chemical
Name
NIOSH TWA
(mg/m3)
NIOSH STEL
(ppm)
NIOSH STEL
(mg/m3)
NIOSH
Carcinogen
ACGIH TWA
(ppm)
ACGIH TWA
(mg/m3)
ACGIH STEL
(ppm)
ACGIH STEL
(mg/m3)
ACETONE 590 250 500
BENZENE 1c 1 0.5 2.5
METHYL
ACETATE
610 250 760 200 250
Chemical
Name
ACGIH
Carcinogen
ACGIH
Notations
ACGIH
TLV Basis
ACETONE A4 A4; BEI URT & eye irr;
CNS impair
BENZENE A1 Skin; A1; BEI Leukemia
METHYL
ACETATE
Headache;
dizziness;
nausea; eye
dam
(degeneration
of ganglion
cells in the
retina)
(C) – Ceiling limit, A1 – Confirmed Human Carcinogen, A4 – Not Classifiable as a Human Carcinogen, BEI – Substances for which there is a
Biological Exposure Index or Indices, CNS – Central nervous system, dam – Damage, impair – Impairment, irr – Irritation, URT – Upper respiratory
tract
SECTION 9) PHYSICAL AND CHEMICAL PROPERTIES
Physical and Chemical Properties
Appearance Clear liquid
Odor Threshold N/A
Odor Description Characteristic
pH N/A
Water Solubility N/A
Flammability Flash point below 73 F/23 C
Flash Point Symbol C
Flash Point -17 ESTIMATE C
Viscosity N/A
Lower Explosion Level N/A
Upper Explosion Level N/A
Vapor Pressure N/A
Vapor Density N/A
Freezing Point N/A
Melting Point N/A
Low Boiling Point N/A
High Boiling Point N/A
Auto Ignition Temp N/A
Specific Gravity 0.82
Density 6.85 lb/gal
% VOC 0.00%
Density VOC 0.00 lb/gal
% Solids By Weight 0.00%
20-80 Blend
Page 6 of 10 www.aglayne.com

Decomposition Pt N/A
Evaporation Rate N/A
Coefficient Water/Oil N/A
VOC Composite Partial Pressure 0.00227333 mmHg
SECTION 10) STABILITY AND REACTIVITY
Stability
Stable under normal conditions of use.
Conditions to Avoid
Avoid heat, sparks, open flames and other ignition sources.
Hazardous Reactions/Polymerization
No data available.
Incompatible Materials
Strong oxidizing agents.
Hazardous Decomposition Products
Thermal decomposition may yield carbon dioxide and/or carbon monoxide.
SECTION 11) TOXICOLOGICAL INFORMATION
Likely route of exposure
Inhalation, ingestion, skin absorption
Acute toxicity
Ingestion: May be harmful or fatal if swallowed.
Based on available data, the classification criteria are not met.
Skin Corrosion/Irritation
Causes skin irritation
0000067-64-1 ACETONE
Can cause skin irritation.
Serious eye damage/irritation
Causes serious eye irritation
0000067-64-1 ACETONE
Exposure can irritate the eyes.
Germ cell mutagenicity
May cause genetic defects.
Carcinogenicity
May cause cancer.
Respiratory/Skin Sensitization
Slightly irritating to respiratory system.
Based on available data, the classification criteria are not met.
0000067-64-1 ACETONE
Can irritate the nose and throat causing coughing and wheezing.
Reproductive toxicity
Based on available data, the classification criteria are not met.
Specific Target Organ Toxicity – Repeated Exposure
Based on available data, the classification criteria are not met.
Aspiration hazard
20-80 Blend
Page 7 of 10 www.aglayne.com

Based on available data, the classification criteria are not met.
Specific Target Organ Toxicity – Single Exposure
May cause drowsiness or dizziness
0000067-64-1 ACETONE
May affect the kidneys and liver.
Likely Routes of Exposure
Inhalation, Ingestion, Skin contact, Eye contact
0000067-64-1 ACETONE
Substance can be absorbed into the body by inhalation.
Potential Health Effects – Miscellaneous
0000067-64-1 ACETONE
The following medical conditions may be aggravated by exposure: lung disease, eye disorders, skin disorders. Overexposure may cause
damage to any of the following organs/systems: blood, central nervous system, eyes, kidneys, liver, respiratory system, skin.
0000067-64-1 ACETONE
LC 50 (male rat): 30000 ppm ( 4 -hour exposure); cited as 71000 mg/m 3 ( 4 -hour exposure) ( 29 )
LC 50 (male mouse): 18600 ppm ( 4 -hour exposure); cited as 44000 mg/m 3 ( 4 -hour exposure) ( 29 )
LD 50 (oral, female rat): 5800 mg/kg ( 24 )
LD 50 (oral, mature rat): 6700 mg/kg (cited as 8.5 mL/kg) ( 31 )
LD 50 (oral, newborn rat): 1750 mg/kg (cited as 2.2 mL/kg) ( 31 )
LD 50 (oral, mouse): 3000 mg/kg ( 32 ,unconfirmed)
LD 50 (dermal, rabbit): Greater than 16000 mg/kg cited as 20 mL/kg) ( 30 )
0000079-20-9 METHYL ACETATE
LC50 (rat): 16000-32000 ppm (4-hour exposure) (9)
LD 50 (oral, rat): greater than 5000 mg/kg ( 4 )
LD 50 (oral, rabbit): 3700 mg/kg (cited as 50 millimols/kg) ( 10 )
LD 50 (skin, rabbit): greater than 5000 mg/kg ( 4 )
0000071-43-2 BENZENE
LC50 (rat): 13,700 ppm (4 hour exposure) (26); 9,980 ppm (7 hour exposure) (13,200 ppm – equivalent 4 hour exposure) (18)
LD 50 (oral, rat): 930 mg/kg ( 19 ); 5,600 mg/kg ( 2 ); 11.4 ml/kg ( 10,032 mg/kg) ( 21 )
LD 50 (oral, mouse): 4,700 mg/kg ( 11 ; unconfirmed)
LD 50 (skin, rabbit and guinea pig): Greater than 9,400 mg/kg ( 20 )
SECTION 12) ECOLOGICAL INFORMATION
Toxicity
Based on available data, the classification criteria are not met.
Mobility in Soil
0000067-64-1 ACETONE
The substance is not PBT / vPvB
The substance is not PBT / vPvB.
Bioaccumulative Potential
No data available.
Persistence and Degradability
0000067-64-1 ACETONE
91% readily biodegradable, Method: OECD Test Guideline 301B
Readily biodegradable.
Other adverse effects
No data available.
20-80 Blend
Page 8 of 10 www.aglayne.com

SECTION 13) DISPOSAL CONSIDERATIONS
Waste Disposal Method
Under RCRA it is the responsibility of the user of the product to determine at the time of disposal whether the product meets RCRA criteria
for hazardous waste. Waste management should be in full compliance with federal, state and local laws.
Empty Containers retain product residue which may exhibit hazards of material, therefore do not pressurize, cut, glaze, weld or use for
any other purposes. Return drums to reclamation centers for proper cleaning and reuse.
SECTION 14) TRANSPORT INFORMATION
U.S. DOT Information
UN1993, Flammable Liquids, N.O.S. (Acetone, Methyl Acetate) 3, PG II
Emergency Response Guide (ERG)
Emergency Response Guide 128
SECTION 15) REGULATORY INFORMATION
CAS Chemical Name % By Weight Regulation List
0000067-64-1 ACETONE 61.780% – 92.670% CERCLA,SARA312,VOC_exempt,TS
CA,RCRA,OSHA
0000079-20-9 METHYL ACETATE 18.220% – 27.330% SARA312,VOC_exempt,TSCA,OSHA
0000071-43-2 BENZENE 0 – 0.001 % SARA313,
CERCLA,SARA312,VOC,IARCCarcin
ogen,TSCA,RCRA, OSHA
Carcinogen,CA_TAC_TOX,CA_TAC_
Carcinogen,CA_Carcinogen,NEI –
National Emissions
Inventory,CA_Prop65 – California
Proposition
65,CA_Prop65_Type_Toxicity_Cance
r –
CA_Proposition65_Type_Toxicity_Ca
ncer,CA_Prop65_Type_Toxicity_Dev
elop –
CA_Proposition65_Type_Toxicity_De
velopmental,CA_Prop65_Type_Toxic
ity_Male –
CA_Proposition65_Type_Toxicity_Ma
le,OSHA
WARNING: This product can expose you to chemicals including BENZENE which is known to the State of California to cause cancer and
BENZENE which is known to the State of California to cause birth defects or other reproductive harm. For more information go to
www.P65Warnings.ca.gov
SECTION 16) OTHER INFORMATION
General
20-80 Blend
Page 9 of 10 www.aglayne.com

A.G. Layne, Inc. urges each customer or recipient of this SDS to study it carefully and consult appropriate expertise, as necessary or
appropriate, to become aware of and understand the data contained in this SDS and any hazards associated with the product. It is the
Buyer’s/User’s responsibility to ensure that his activities comply with all Federal, State, Provincial or Local laws. The information
presented here pertains only to the product as shipped. The information contained herein is based on our current knowledge of the
underlying data and is intended to describe the product for the purpose of health, safety and environmental requirements only. NO
warranty or guarantee is expressed or implied regarding the accuracy of this data or the results to be obtained from the use of the product.
3
2
H
0
/
Health
FLAMMABILITY
Physical Hazard
Personal Protection
HMIS
( * ) – Chronic effects
Caution: HMIS ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks
Version 1.0:
Revision Date: May 04, 2021
First Edition.
DISCLAIMER
To the best of our knowledge, the information contained herein is accurate. However, neither A. G. Layne, Inc. nor any of its subsidiaries assumes any
liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole
responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we
cannot guarantee that these are the only hazards that exist. The above information pertains to this product as currently formulated, and is based on the
information available at this time. Addition of reducers or other additives to this product may substantially alter the composition and hazards of the product.
Since conditions of use are outside our control, we make no warranties, express or implied, and assume no liability in connection with any use of this
information.
20-80 Blend
Page 10 of 10 www.aglayne.com

10A101_SDS.pdf

by | Sep 27, 2025

Product #: 5317 From: BRENNTAG PACIFIC INC. To: REVCHEM Monday, August 12, 2024
BD BRENNTAG
1, Identification
Other means of identification | None known.
Product identifier ACETONE
Other means of Identification
CAS number 67-64-1
Recommended use ALL PROPER AND LEGAL PURPOSES
Recommended restrictions None known.
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name Brenntag Pacific Inc.
Address 10747 Patterson Place
Santa Fe Springs, CA 90670
Telephone 562-903-9626
E-mail Not available
Emergency phone number 800-424-9300 CHEMTREC
2. Hazard(s) identification
Physical hazards Flammable liquids Category 2
Health hazards Serious eye damageleye irritation Category 2A
Specific target organ toxicity, single exposure Category 3 narcotic effects
Environmental hazards Not classified.
OSHA defined hazards Not classified.
Label elements
Signal word Danger
Hazard statement Highly flammable liquid and vapor. Causes serious eye irrilation. May cause drowsiness or
dizziness.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. – No smoking. Keep container tightly
closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist/vapors. Wash thoroughly after handling
Use only outdoors or in a well-ventilated area. Wear protective gloves/protective clothing/eye
protection/face protection.

Response If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.

If inhaled: Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse
cautiously with water for several minutes. Remove contact lenses, if present and easy to do.
Continue rinsing. Call a poison center/doctor if you feel unwell. If eye irritation persists: Get
medical advice/attention. In case of fire: Use appropriate media to extinguish.

Storage Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.

Keep cool. Store locked up.

Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.
Hazard(s) not otherwise Static accumulating flammable liquid can become electrostatically charged even in bonded and
classified (HNOC) grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion.
Supplemental information None.

3. Composition/information on ingredients

Substances

Material name: ACETONE SDS us
935752 Version #: 54 Revision date: 05-14-2024 _ Issue date: 07-25-2016 1/8

10A103_SDS.pdf

by | Sep 27, 2025

Univar
Solutions
Safety Data Sheet
Acetone
Version 2.9 Revision Date: 09/03/2019
SECTION 1. PRODUCT AND COMPANY IDENTIFICATION
Product name : Acetone
Recommended use of the chemical and restrictions on use
Recommended use : Solvent.
Manufacturer or supplier’s details
Company : Univar Solutions USA, Inc.
Address 3075 Highland Pkwy Suite 200
Downers Grove, IL 60515
United States of America (USA)
Emergency telephone number:
Transport North America: CHEMTREC (1-800-424-9300)
CHEMTREC INTERNATIONAL Tel # 703-527-3887
Additional Information: : Responsible Party: Product Compliance Department
E-mail: SDSNA@univarsolutions.com
SDS Requests: 1-855-429-2661
Website: www.univarsolutions.com
SECTION 2. HAZARDS IDENTIFICATION
GHS Classification
Flammable liquids : Category 2
Eye irritation : Category 2A
Specific target organ toxicity : Category 3 (Central nervous system)
– single exposure
GHS label elements
Hazard pictograms $ e t
Signal word : Danger
Hazard statements : H225 Highly flammable liquid and vapour.
H319 Causes serious eye irritation.
H336 May cause drowsiness or dizziness.
Precautionary statements : Prevention:
P210 Keep away from heat/sparks/open flames/hot surfaces.
No smoking.
P233 Keep container tightly closed.
P240 Ground/bond container and receiving equipment.
P241 Use explosion-proof electrica!/ ventilating/ lighting equip-
ment.
P242 Use only non-sparking tools.

10A101T_SDS.pdf

by | Sep 27, 2025

Product #: 5317 From: BRENNTAG PACIFIC INC. To: Wednesday, August 26 ,20 15
BRENNTAC aaa: SAFETY DATA SHEET
7
1. Identification
Product identifier ACETONE
Other means of identification None.
Recommended use ALL PROPER AND LEGAL PURPOSES.
Recommended restrictions None known
Manufacturer/Importer/Supplier/Distributor information
Manufacturer
Company name Brenntag Pacific Inc.
Address 10747 Patterson Place
Santa Fe Springs, CA 90670
Telephone 562-903-9626
E-mail Not available.
Emergency phone number _ 800-424-9300 CHEMTREC.
2. Hazard(s) identification
Physical hazards Flammable liquids Category 2
Health hazards Serious eye damage/eye irritation Category 2A
Specific target organ toxicity, single exposure Category 3 narcotic effects
Environmental hazards Hazardous to the aquatic environment, acute Category 3
hazard
Hazardous to the aquatic environment, Category 3
long-term hazard
OSHA defined hazards Not classified.
Label elements
Signal word Danger
Hazard statement Highly flammable liquid and vapor. Causes serious eye irritation. May cause drowsiness or
dizziness. Harmful to aquatic life. Harmful to aquatic life with long lasting effects.
Precautionary statement
Prevention Keep away from heat/sparks/open flames/hot surfaces. – No smoking. Keep container tightly
closed. Ground/bond container and receiving equipment. Use explosion-proof
electrical/ventilating/lighting equipment. Use only non-sparking tools. Take precautionary
measures against static discharge. Avoid breathing mist or vapor. Wash thoroughly after
handling. Use only outdoors or in a well-ventilated area. Avoid release to the environment. Wear
eye protection/face protection. Wear protective gloves/eye protection/face protection.

Response If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.

Storage Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.

Keep cool. Store locked up.

Disposal Dispose of contents/container in accordance with local/regional/nationaV/international regulations.
Hazard(s) not otherwise Static accumulating flammable liquid can become electrostatically charged even in bonded and
classified (HNOC) grounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion
Supplemental information None.

Material name: ACETONE. sos US
935752 Version #:13 Revision date: 05-29-2015 Issue date: 03-11-2015 1/8

10A101S_SDS.pdf

by | Sep 27, 2025

Response If on skin (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower.

Storage Store in a well-ventilated place. Keep container tightly closed. Store in a well-ventilated place.

Keep cool. Store locked up.

Material name: ACETONE. sos US
935752 Version #:13 Revision date: 05-29-2015 Issue date: 03-11-2015 1/8

09TEM1_SDS.pdf

by | Sep 27, 2025

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 01: Chemical Product and Company Identification
Walker Emulsions Inc.
4401 SE Johnson Creek Blvd
Portland, OR, USA 97222
503-659-1708
Manufacturer
As aboveSupplier
Walker Emulsions Inc. – Department of Research and Development
Contact: Steven M. Brown 503-659-1708
Prepared By
May 01, 2012Preparation Date
May 23, 2018Revision Date
853-NB Resin CleanerProduct Name
103149 (prior to 11/1/15: PT2510.32)Product Number
MixtureCAS Number
Not Applicable/MixtureChemical Formula
Alkaline CleanerMaterial Use
Infotrac (800) 535-505324 Hour Emergency Number
Section 02: Hazards Identification
WarningSignal Word:
H319 Causes serious eye irritation.
Serious eye damage/eye irritation, Category 2/2A
H312 Harmful in contact with skin.
Acute toxicity, Category 4
H335 + H336 May cause respiratory irritation, drowsiness or dizziness.
Specific target organ toxicity-single exposure, Category 3
H302 Harmful if swallowed.
Acute toxicity, Category 4
Hazards:
P102 Keep out of reach of children.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
Prevention:
P301 + P315 + P330 + P331 IF SWALLOWED: Get immediate medical
advice/attention. Rinse mouth. DO NOT INDUCE vomiting.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all
contaminated clothing. Rinse skin with water/shower.
P332 + P313 If skin irritation occurs: Get medical advice/attention.
P304 + P341 IF INHALED: If breathing is difficult, remove victim to fresh air and
keep at rest in a position comfortable for breathing.
P315 + P342: If experiencing respiratory symptoms, get medical advice/attention.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 If eye irritation persists: Get medical advice/attention.
Response:
P501: Dispose of contents/container in accordance with local regulations.Disposal:
Page 1 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 02: Hazards Identification
Effects of Acute Exposure
Causes serious irritation to eyes.Eye Contact
Ingestion of this material may be harmful.Ingestion
Inhalation of vapors or mists may cause pulmonary irritation, dizziness, and
nausea.
Inhalation
May be absorbed through skin.Skin Absorption
Causes serious irritation to skin.Skin Contact
Effects of Chronic Exposure
Prolonged or repeated breathing of sprays, mists, or dusts in excess of the
suggested TLV may cause severe nasal and respiratory irritations.
Inhalation
Prolonged or repeated contact with skin may cause irritation, redness, itching
and/or be potentially absorbed in harmful amounts. Persons with pre-existing
dermatitis may be more susceptible to the effects of this product.
Skin
Section 03: Composition and Information on Ingredients
Hazardous Ingredients
Exposure LevelsC.A.S. # TSCAHazard Rating LD/LC, Route, SpeciesIngred / %
SODIUM METASILICATE
1 – 5 6834-92-0
See Section 11
Not AvailableY Health:2, fire:0, React:0, PP:E
LD/50:
LC/50:
1-METHOXY PROPANOL
1 – 5 107-98-2
See Section 11
See Section 11Y Health:2, Fire:3, React: 0,
PP:G
LD/50:
LC/50:
DIPROPYLENE GLYCOL METHYL ETHER
1-5 34590-94-8
See Section 11
Not AvailableY Health:1, fire:2, React:0, PP:G
LD/50:
LC/50:
HEALTH: 2, FIRE: 1, REACTIVITY: 0, PPI: XHMIS Rating (0-4)
HEALTH
2
PROTECTIVE
EQUIPMENT
X
REACTIVITY
0
FLAMMABILITY
1
Section 04: First Aid Measures
Remove contaminated clothing and wash affected skin area with soap and water.
If irritation persists, contact a physician.
Skin Contact
Remove person to fresh air. If not breathing, give artificial respiration. If breathing
is difficult, give oxygen. Call a physician promptly.
Inhalation
DO NOT induce vomiting. Call a physician promptly. Give large quantities of water
or milk. Never give anything orally to an unconscious or convulsing person.
Ingestion
Immediately flush eyes with plenty of water for at least 15 minutes. Call a physician
promptly.
Eye Contact
Page 2 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 05: Fire and Explosion Data
>200 F, (93 C), SetaflashFlash Point, Method
IIIAFlammability
Use self-contained breathing apparatus with full facepiece.Special Procedures
Not AvailableFire Hazards
Never use welding or cutting torch on or near drum, even empty, because product
or residue can ignite potentially explosively.
Explosion Hazards
Not AvailableHazardous Combustion Products
Not AvailableExplosive Range:
Water spray, dry chemical, chemical foam, or carbon dioxide.Extinguishing Media
Section 06: Accidental Release Measures
SMALL SPILLS: Use an inert material such as kitty litter, sawdust or cellulosic
based absorbent to absorb spilled product. Flush spill area with plenty of water.
Rinsate may require special processing and approval prior to discharging to a
sanitary sewer system.
LARGE SPILLS: Use caution; spilled material may be extremely slippery. Contain
spilled material immediately and prevent from entering the sewer system. Use inert
materials mentioned above to dam, dike, divert or absorb spill. Absorb or vacuum
spilled material for proper disposal options.
Leak/Spill
Section 07: Handling and Storage
Containers of this material may be hazardous when emptied. Since emptied
containers retain product residues (vapor, liquid, and/or solid), all hazard
precautions given in this data sheet should be observed. Rinse container with 1-2
gallons of water and recycle into end-use process.
Handling
Section 08: Exposure Control and Personal Protection
Protective Equipment
Wear approved splashproof chemical goggles.Eye/Type
None normally required.Respiratory/Type
Neoprene rubber gloves are recommended.Gloves/Type
Use adequate ventilation to keep airborne concentrations below the exposure
standard.
Ventilation Requirements
Use as needed to keep this material off clothing and skin.Other Protective Equipment
SODIUM METASILICATE 1-METHOXY PROPANOL DIPROPYLENE
GLYCOL
METHYL ETHER
Occupational Exposure Limits
N/est 100.00 PPM 100.00 PPMACGIH TLV
N/est N/est N/estACGIH TLV-C
N/est 150.00 PPM 150.00 PPMACGIH STEL
N/est 150.00 PPM 150.00 PPMOSHA STEL
N/est 100.00 PPM 100.00 PPMOSHA PEL
Section 09: Physical and Chemical Properties
LiquidPhysical State
Page 3 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 09: Physical and Chemical Properties
BlueAppearance
Not AvailableViscosity (cPs, water=1)
Not AvailableVolatility (wt%)
Not applicableVolatility (vol%)
1.04839Specific Gravity
11.95-12.05pH
MiscibleSolubility in Water
Slight glycol etherOdor
Not AvailableOdor threshold (ppm)
(WATER) 17 @ 68 F (20 C)Vapor Pressure (mm Hg)
Non volatileVapor Density (air=1)
UnavailableEvaporation Rate (n-butyl
acetate=1)
Not AvailableCoefficient of water/oil distribution
(WATER) 212 F (100 C)Boiling Range
Not AvailablePartition Coefficient
Not AvailableFreezing Point
Not AvailableMelting Point
Not availableVOC
Not AvailableFlash Point (TCC)
MixtureMolecular Weight
Not AvailableExplosive limits
Not AvailableFlammability (solid, gas)
Not AvailableAuto-ignition temperature
Not Available Decomposition temperature
Section 10: Stability and Reactivity Data
Hazardous polymerization will not occur.Hazardous Polymerization
This product is stable.Chemical Stability
Acids, strong oxidizing agents.Incompatibility
Acids, strong oxidizing agents.Conditions to Avoid
Not AvailableReactivity Conditions
Carbon monoxide and/or carbon dioxide.Hazardous Products of
Decomposition (thermal)
Section 11: Toxicological Information
Eye contact, potential skin absorption, inhalation, and ingestion.Routes of Entry
Exposure Limits
Page 4 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 11: Toxicological Information
SODIUM METASILICATE:
Oral, Rat, adult 1,153 mg/kg
Skin, Rat, adult 250 PPM
1-METHOXY PROPANOL:
Oral, Rat, adult 5,660 PPM
Skin, Rat, adult 13,000 PPM
DIPROPYLENE GLYCOL METHYL ETHER:
Oral, Rat, adult 5.4 ml/kg
Skin, Rabbit, adult 20
LD/50
1-METHOXY PROPANOL:
Inhalation, Rat, adult 7,000 PPM
LC/50
Not AvailableTWA
This product does not contain any substance(s) listed as a carcinogen by NTP,
IARC, or OSHA.
Carcinogenicity
None KnownTeratogenicity/Mutagenicity
None KnownReproductive Effects
None KnownSynergistic Materials
None available for product.Additional Toxicological Data
Section 12: Ecological Information
Not AvailableEnvironmental
Aquatic toxicity not available.Ectotoxicological Information
Not AvailableBiodegradability
Section 13: Disposal Considerations
NONEEPA Hazardous Waste Number
Waste product must be disposed of properly under Federal and State regulations
for industrial waste. Absorbed material on cellulosic or similar synthetic absorbents
may be incinerated pending approvals. This product, as delivered, when spilled or
disposed of is not regulated under 40 CFR Part 261 of the RCRA Hazardous
Waste Regulations.
Waste Disposal
Section 14: Transport Information
NONEU.N. #
NAT.D.G. Classification
Not HazardousD.O.T. Classification
D2BWHMIS Classification
Section 15: Regulatory Information
IrritantEEC Classification
This product is not regulated as a hazardous substance.U.S. Federal Regulations
Page 5 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: 853-NB RESIN CLEANER
Section 15: Regulatory Information
SARA TITLE III SECTION 313:
This product contains the following toxic chemicals subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to
Know Act of 1986 and of 40 CFR 372:
Chemical Name: DIPROPYLENE GLYCOL METHYL ETHER, CAS#: 34590-94-8,
<5% U.S. Federal Regulations All ingredients are listed in the TSCA inventory.US TSCA Section 16: Other Information Do not dilute or mix with other materials unless advised by supplier. The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information provided. Page 6 of 6

09TEM-5_SDS.pdf

by | Sep 27, 2025

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 01: Chemical Product and Company Identification
Walker Emulsions Inc.
4401 SE Johnson Creek Blvd
Portland, OR, USA 97222
503-659-1708
Manufacturer
As aboveSupplier
Walker Emulsions Inc. – Department of Research and Development
Contact: Steven M. Brown 503-659-1708
Prepared By
May 01, 2012Preparation Date
May 23, 2018Revision Date
Marathon Tool Wash 132Product Name
105030 (prior to 11/1/15: PT2501.32)Product Number
MixtureCAS Number
Not Applicable/MixtureChemical Formula
Alkaline CleanerMaterial Use
Infotrac (800) 535-505324 Hour Emergency Number
Section 02: Hazards Identification
WarningSignal Word:
H319 Causes serious eye irritation.
Serious eye damage/eye irritation, Category 2/2A
H312 Harmful in contact with skin.
Acute toxicity, Category 4
H335 + H336 May cause respiratory irritation, drowsiness or dizziness.
Specific target organ toxicity-single exposure, Category 3
H302 Harmful if swallowed.
Acute toxicity, Category 4
Hazards:
P102 Keep out of reach of children.
P202 Do not handle until all safety precautions have been read and understood.
P261 Avoid breathing dust/fume/gas/mist/vapors/spray.
P262 Do not get in eyes, on skin, or on clothing.
P264 Wash skin thoroughly after handling.
Prevention:
P301 + P315 + P330 + P331 IF SWALLOWED: Get immediate medical
advice/attention. Rinse mouth. DO NOT INDUCE vomiting.
P303 + P361 + P353 IF ON SKIN (or hair): Remove/Take off immediately all
contaminated clothing. Rinse skin with water/shower.
P332 + P313 If skin irritation occurs: Get medical advice/attention.
P304 + P341 IF INHALED: If breathing is difficult, remove victim to fresh air and
keep at rest in a position comfortable for breathing.
P315 + P342: If experiencing respiratory symptoms, get medical advice/attention.
P305 + P351 + P338 IF IN EYES: Rinse cautiously with water for several minutes.
Remove contact lenses, if present and easy to do. Continue rinsing.
P337 + P313 If eye irritation persists: Get medical advice/attention.
Response:
P501: Dispose of contents/container in accordance with local regulations.Disposal:
Page 1 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 02: Hazards Identification
Effects of Acute Exposure
Causes serious irritation to eyes.Eye Contact
Ingestion of this material may be harmful.Ingestion
Inhalation of vapors or mists may cause pulmonary irritation, dizziness, and
nausea.
Inhalation
May be absorbed through skin.Skin Absorption
Causes serious irritation to skin.Skin Contact
Effects of Chronic Exposure
Prolonged or repeated breathing of sprays, mists, or dusts in excess of the
suggested TLV may cause severe nasal and respiratory irritations.
Inhalation
Prolonged or repeated contact with skin may cause irritation, redness, itching
and/or be potentially absorbed in harmful amounts. Persons with pre-existing
dermatitis may be more susceptible to the effects of this product.
Skin
Section 03: Composition and Information on Ingredients
Hazardous Ingredients
Exposure LevelsC.A.S. # TSCAHazard Rating LD/LC, Route, SpeciesIngred / %
SODIUM METASILICATE
1 – 5 6834-92-0
See Section 11
Not Available
LD/50:
LC/50:
1-METHOXY PROPANOL
1 – 5 107-98-2
See Section 11
See Section 11
LD/50:
LC/50:
DIPROPYLENE GLYCOL METHYL ETHER
1-5 34590-94-8
See Section 11
Not Available
LD/50:
LC/50:
HEALTH: 2, FIRE: 1, REACTIVITY: 0, PPI: XHMIS Rating (0-4)
HEALTH
2
PROTECTIVE
EQUIPMENT
X
REACTIVITY
0
FLAMMABILITY
1
Section 04: First Aid Measures
Remove contaminated clothing and wash affected skin area with soap and water.
If irritation persists, contact a physician.
Skin Contact
Remove person to fresh air. If not breathing, give artificial respiration. If breathing
is difficult, give oxygen. Call a physician promptly.
Inhalation
DO NOT induce vomiting. Call a physician promptly. Give large quantities of water
or milk. Never give anything orally to an unconscious or convulsing person.
Ingestion
Immediately flush eyes with plenty of water for at least 15 minutes. Call a physician
promptly.
Eye Contact
Section 05: Fire and Explosion Data
Page 2 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 05: Fire and Explosion Data
>200 F, (93 C), SetaflashFlash Point, Method
IIIAFlammability
Use self-contained breathing apparatus with full facepiece.Special Procedures
Not AvailableFire Hazards
Never use welding or cutting torch on or near drum, even empty, because product
or residue can ignite potentially explosively.
Explosion Hazards
Not AvailableHazardous Combustion Products
Not AvailableExplosive Range:
Water spray, dry chemical, chemical foam, or carbon dioxide.Extinguishing Media
Section 06: Accidental Release Measures
SMALL SPILLS: Use an inert material such as kitty litter, sawdust or cellulosic
based absorbent to absorb spilled product. Flush spill area with plenty of water.
Rinsate may require special processing and approval prior to discharging to a
sanitary sewer system.
LARGE SPILLS: Use caution; spilled material may be extremely slippery. Contain
spilled material immediately and prevent from entering the sewer system. Use inert
materials mentioned above to dam, dike, divert or absorb spill. Absorb or vacuum
spilled material for proper disposal options.
Leak/Spill
Section 07: Handling and Storage
Containers of this material may be hazardous when emptied. Since emptied
containers retain product residues (vapor, liquid, and/or solid), all hazard
precautions given in this data sheet should be observed. Rinse container with 1-2
gallons of water and recycle into end-use process.
Handling
Section 08: Exposure Control and Personal Protection
Protective Equipment
Wear approved splashproof chemical goggles.Eye/Type
None normally required.Respiratory/Type
Neoprene rubber gloves are recommended.Gloves/Type
Use adequate ventilation to keep airborne concentrations below the exposure
standard.
Ventilation Requirements
Use as needed to keep this material off clothing and skin.Other Protective Equipment
SODIUM METASILICATE 1-METHOXY PROPANOL DIPROPYLENE
GLYCOL
METHYL ETHER
Occupational Exposure Limits
N/est 100.00 PPM 100.00 PPMACGIH TLV
N/est N/est N/estACGIH TLV-C
N/est 150.00 PPM 150.00 PPMACGIH STEL
N/est 150.00 PPM 150.00 PPMOSHA STEL
N/est 100.00 PPM 100.00 PPMOSHA PEL
Section 09: Physical and Chemical Properties
LiquidPhysical State
Page 3 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 09: Physical and Chemical Properties
BlueAppearance
Not AvailableViscosity (cPs, water=1)
Not AvailableVolatility (wt%)
Not applicableVolatility (vol%)
1.04839Specific Gravity
11.95-12.05pH
MiscibleSolubility in Water
Slight glycol etherOdor
Not AvailableOdor threshold (ppm)
(WATER) 17 @ 68 F (20 C)Vapor Pressure (mm Hg)
Non volatileVapor Density (air=1)
UnavailableEvaporation Rate (n-butyl
acetate=1)
Not AvailableCoefficient of water/oil distribution
(WATER) 212 F (100 C)Boiling Range
Not AvailablePartition Coefficient
Not AvailableFreezing Point
Not AvailableMelting Point
Not availableVOC
Not AvailableFlash Point (TCC)
MixtureMolecular Weight
Not AvailableExplosive limits
Not AvailableFlammability (solid, gas)
Not AvailableAuto-ignition temperature
Not Available Decomposition temperature
Section 10: Stability and Reactivity Data
Hazardous polymerization will not occur.Hazardous Polymerization
This product is stable.Chemical Stability
Acids, strong oxidizing agents.Incompatibility
Acids, strong oxidizing agents.Conditions to Avoid
Not AvailableReactivity Conditions
Carbon monoxide and/or carbon dioxide.Hazardous Products of
Decomposition (thermal)
Section 11: Toxicological Information
Eye contact, potential skin absorption, inhalation, and ingestion.Routes of Entry
Exposure Limits
Page 4 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 11: Toxicological Information
SODIUM METASILICATE:
Oral, Rat, adult 1,153 mg/kg
Skin, Rat, adult 250 PPM
1-METHOXY PROPANOL:
Oral, Rat, adult 5,660 PPM
Skin, Rat, adult 13,000 PPM
DIPROPYLENE GLYCOL METHYL ETHER:
Oral, Rat, adult 5.4 ml/kg
Skin, Rabbit, adult 20
LD/50
1-METHOXY PROPANOL:
Inhalation, Rat, adult 7,000 PPM
LC/50
Not AvailableTWA
This product does not contain any substance(s) listed as a carcinogen by NTP,
IARC, or OSHA.
Carcinogenicity
None KnownTeratogenicity/Mutagenicity
None KnownReproductive Effects
None KnownSynergistic Materials
None available for product.Additional Toxicological Data
Section 12: Ecological Information
Not AvailableEnvironmental
Aquatic toxicity not available.Ectotoxicological Information
Not AvailableBiodegradability
Section 13: Disposal Considerations
NONEEPA Hazardous Waste Number
Waste product must be disposed of properly under Federal and State regulations
for industrial waste. Absorbed material on cellulosic or similar synthetic absorbents
may be incinerated pending approvals. This product, as delivered, when spilled or
disposed of is not regulated under 40 CFR Part 261 of the RCRA Hazardous
Waste Regulations.
Waste Disposal
Section 14: Transport Information
NONEU.N. #
NAT.D.G. Classification
Not HazardousD.O.T. Classification
D2BWHMIS Classification
Section 15: Regulatory Information
IrritantEEC Classification
This product is not regulated as a hazardous substance.U.S. Federal Regulations
Page 5 of 6

Safety
Data SheetA Walker Industries Company
PRODUCT: Marathon Tool Wash 132
Section 15: Regulatory Information
SARA TITLE III SECTION 313:
This product contains the following toxic chemicals subject to the reporting
requirements of Section 313 of the Emergency Planning and Community Right to
Know Act of 1986 and of 40 CFR 372:
Chemical Name: DIPROPYLENE GLYCOL METHYL ETHER, CAS#: 34590-94-8,
<5% U.S. Federal Regulations All ingredients are listed in the TSCA inventory.US TSCA Section 16: Other Information Do not dilute or mix with other materials unless advised by supplier. The information and recommendations contained herein are based upon data believed to be correct. However, no guarantee or warranty of any kind, expressed or implied, is made with respect to the information provided. Page 6 of 6

« Older Entries

Next Entries »

Our Mission