Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
9/21/2022
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
9/21/2022
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3-D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life-saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils dry) 3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
9/21/2022
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
SCREAMIN
General Description
DayGlo SRX latex paint is a premium, low odor,
fluorescent, water-based paint. Maximum lightfastness
and film integrity are dependent upon the use of
DayGlo SRX Filteray W (clear overcoat) which is
described below.
* Studies indicate that if an all-purpose single color is
desired for impact, Blaze Orange is generally best for
contrast with most natural backgrounds. DayGlo s
fluorescent colors do not tend to appear white, gray, or black (achromatic) at extreme distances
and at dusk, dawn or low light conditions as do most non-fluorescent colors. This is a huge
benefit for signage and any product that needs to be seen in a work environment for safety or
efficiency.
** Filteray W is a clear overcoat designed for use over the SRX fluorescent latex paint. The
Filteray W absorbs some of the harmful rays of the sun that cause premature fading of
fluorescent colors during continued exposure to direct sunlight. A topcoat of Filteray W can
double the lightfastness of DayGlo s fluorescent colors. Ordinary varnishes and overcoats do
not have the protective action of the SRX Filteray W overcoat and can do more harm than good
when used over DayGlo s fluorescent colors.
The final surface produced by the Filteray W overcoat is harder and has a higher gloss than the
DayGlo SRX latex paint alone. This means that it will be more resistant to wear and more easily
cleaned. The quantity of Filteray W overcoat required is usually 2/3 that of the paint.
Features
Formaldehyde Free Formulation
Low Odor
Environmentally Friendly
100% Acrylic Latex

Physical properties
Grind 5.0 Min Hegman Gage
Viscosity 1,500 – 2,500 cps @ 77*F
pH 8.00-9.00

Available Colors
Product Code Color
SRX-11 Aurora Pink
SRX-13 Rocket Red
SRX-15 Blaze Orange*
SRX-17 Saturn Yellow
SRX-18 Signal Green
SRX-19 Horizon Blue
SRX-20 Ultra Violet
SRX-08A Filteray W**

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
Applications
The DayGlo SRX latex paint can be used anywhere that requires a high visibility brushing paint.
Some of the general areas of use include:
Theatrical and Special Effects: For use in haunted houses and stage painting. They can also be
used to create 3- D images.
Graphic Arts: For outdoor advertising signs, murals, painted bulletins, store signs, truck signs,
and trade exhibits.
Safety: For aviation, industrial and marine uses on aircraft, ground support equipment,
navigational aids, safety markings, equipment, machinery, fire protection equipment, first aid
kits, traffic controls, boats, buoys, docks, and life- saving equipment.
Hobby-Sports: For use on models and toys, markings on easily lost sporting equipment
(boomerangs, arrows, fishing gear) and identification markings on personal equipment.
Lightfastness
The useful outdoor life of the color is determined by the thickness and uniformity of the DayGlo
SRX coating. For greatly increased resistance to sunlight, an overcoat of SRX Filteray W is
required.
The following table gives a guide to expected lightfastness. The lower number is representative
of exposure in southern latitudes; the larger number in northern latitudes.

1 heavy coat of DayGlo SRX paint (1.5 mils
dry)
3-6 Months

1 heavy coat of DayGlo SRX paint (1.5 mils
dry) +
1 uniform overcoat of Filteray W (1.5 mils dry)
6-12 Months

2 heavy coats of DayGlo SRX paint (3 mils dry)
+
1 uniform overcoat of Filteray W (1.5 mils dry)
12-24 Months

One coat of DayGlo SRX latex paint is usually sufficient for interior markings, as the color is
virtually unaffected by light sources other than direct sunlight. For storefronts, panel truck signs,
etc., which must last a year or more, apply a coat of Filteray W overcoat over two coats of
DayGlo SRX latex paint.

4515 St. Clair Ave. Cleveland, OH 44103
216-391-1010
www.dayglo.com
Technical Data Sheet

Disclaimer: Our technical advice, information, statements, whether given verbally, in writing, or in the form of test results, is offered
for your guidance without warranty. No warranty for fitness for a particular purpose is made. This also applies where protective
rights of third parties are involved. It does not release the user from obligation to test the suitability of the products and formulas for
the intended process and applications. Our guarantee is limited to the consistent quality of our product.
General Application Instructions
Undercoat:
DayGlo SRX latex paints are semi-transparent and, therefore, brightest when applied over a
clean, white surface. White semi-gloss latex coatings, flat white latex undercoaters, water
based primer-sealers and water-based bulletin blockout whites are ideally suited for this
purpose.
Over old finishes, clean and sand before applying a white undercoat or primer that offers good
adhesion to both the old finish and new DayGlo paint. However, best performance can be
achieved by removing old finishes and starting with a freshly primed surface.
SRX Latex Paint Color Coat:
1. Stir well and if thinning is necessary, use water. (AVOID OVER THINNING).
2. Apply one heavy coat of DayGlo SRX latex paint with a soft brush. Use short strokes.
Cover completely and smooth out as you go to produce a uniform deep layer
(approximately 1.5 mils thick dry). Keep in mind that thin spots or streaks will fade
prematurely. Allow to set-up or “top dry” at least 10 minutes (@ 70oF).
3. Apply the second coat same as the first. Allow 3 hours to dry before applying DayGlo
SRX Filteray W overcoat.
4. For sign applications, the DayGlo SRX coat can simply be roughed in, slightly
overlapping the copy line. Your copy line will not be hidden because DayGlo SCR paint
is semi-transparent. Do not try to work the paint exactly to a line. An opaque
background should be used to cut in accurately to the copy line for sharp detail after the
DayGlo SRX paint has top dried 24 hours.

Filteray Type D Overcoat:
1. Apply one heavy coat of DayGlo SRX Filteray W overcoat (1.5 mils dry). Thin, only if
necessary, using water. This product works best when applied by brush.
2. Allow surface to dry 2 hours before putting into service.
3. Clean brushes should always be used. After use, they can be cleaned up with warm
water.
4. Application of Filteray W will cause the color to deepen. It will have a glossy finish.
5. The use of Filteray W will diminish the UV response of the finished paint.

Tips For Use/Storage:
DayGlo SRX latex paint and Filteray W overcoat may be applied by spray gun. Stir well
and thin to spraying consistency using water, then strain.
The nominal shelf life of the SRX latex paint and Filteray W overcoat is one year in
unopened cans. These products should be stirred before use.

Avoid freezing and close can tightly when not in use. Use with adequate ventilation.

MSDS Name: WAW-21 CORONA MAGENTA TEMPERA PAINT
Revision Date: 07/29/11
Page Number: 1 of 6
SECTION I – PRODUCT AND COMPANY INFORMATION
Product Name: WAW-21 CORONA MAGENTA TEMPERA PAINT
CAS Number MIXTURE
HMIS Rating: Health: 1 Fire: 1 Reactivity: 0
Company Identification: DAY-GLO COLOR CORP.

4515 SAINT CLAIR AVENUE

CLEVELAND OH 44103
Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name CORONA MAGENTA TEMPERA PAINT
Product Code WAW-21
SECTION II – INGREDIENT AND HAZARD INFORMATION
Tngredient- Name –____CAS-Number _____Percent_____ _
(No hazardous ingredients known at this time.)
SECTION III – HAZARDS IDENTIFICATION
EYE CONTACT
May cause irritation.
SKIN CONTACT
May cause irritation.
INHALATION HAZARDS
Outgassing of formaldehyde vapors can be irritating.
INGESTION HAZARDS
Small amounts swallowed are not likely to cause injury. Not a hazard
in normal industrial use.
TARGET ORGANS
No organs affected.
CANCER HAZARDS
This product contains less than 0.1% free formaldehyde and may be
capable of outgassing formaldehyde at levels in excess of OSHA’s
Action Level under some conditions of use. Formaldehyde is a known

4515 SAINT CLAIR AVENUE
CLEVELAND OH 44103

Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name HORIZON BLUE TEMPERA PAINT
Product Code WAW-19
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
(No hazardous ingredients known at this time.)
SECTION III – HAZARDS IDENTIFICATION
EYE CONTACT
May cause irritation.
SKIN CONTACT
May cause irritation.
INHALATION HAZARDS
Outgassing of formaldehyde vapors can be irritating.
INGESTION HAZARDS
Small amounts swallowed are not likely to cause injury. Not a hazard
in normal industrial use.
TARGET ORGANS
No organs affected.
CANCER HAZARDS
This product contains less than 0.1% free formaldehyde and may be
capable of outgassing formaldehyde at levels in excess of OSHA’s
Action Level under some conditions of use. Formaldehyde is a known

MSDS Name: WAW-18 SIGNAL GREEN TEMPERA PAINT
Revision Date: 07/29/11
Page Number: 1 of 6
SECTION I – PRODUCT AND COMPANY INFORMATION
Product Name: WAW-18 SIGNAL GREEN TEMPERA PAINT
CAS Number MIXTURE
HMIS Rating: Health: 1 Fire: 1 Reactivity: 0
Company Identification: DAY-GLO COLOR CORP.

4515 SAINT CLAIR AVENUE

CLEVELAND OH 44103
Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name SIGNAL GREEN TEMPERA PAINT
Product Code WAW-18
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
(No hazardous ingredients known at this time.)
SECTION III – HAZARDS IDENTIFICATION
EYE CONTACT
May cause irritation.
SKIN CONTACT
May cause irritation.
INHALATION HAZARDS
Outgassing of formaldehyde vapors can be irritating.
INGESTION HAZARDS
Small amounts swallowed are not likely to cause injury. Not a hazard
in normal industrial use.
TARGET ORGANS
No organs affected.
CANCER HAZARDS
This product contains less than 0.1% free formaldehyde and may be
capable of outgassing formaldehyde at levels in excess of OSHA’s
Action Level under some conditions of use. Formaldehyde is a known

MSDS Name: WAW-17 SATURN YELLOW TEMPERA PAINT
Revision Date: 07/29/11
Page Number: 1 of 6
SECTION I – PRODUCT AND COMPANY INFORMATION
Product Name: WAW-17 SATURN YELLOW TEMPERA PAINT
CAS Number MIXTURE
HMIS Rating: Health: 1 Fire: 1 Reactivity: 0
Company Identification: DAY-GLO COLOR CORP.

4515 SAINT CLAIR AVENUE

CLEVELAND OH 44103
Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name SATURN YELLOW TEMPERA PAINT
Product Code WAW-17
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
4-AMINONAPHTHALENE- 1, 8-DICARBOXIMIDE 01742-95-6 < 1.0 SECTION III - HAZARDS IDENTIFICATION EYE CONTACT May cause irritation. SKIN CONTACT May cause irritation. INHALATION HAZARDS Outgassing of formaldehyde vapors can be irritating. INGESTION HAZARDS Small amounts swallowed are not likely to cause injury. Not a hazard in normal industrial use. TARGET ORGANS No organs affected. CANCER HAZARDS This product contains less than 0.1% free formaldehyde and may be

MSDS Name: WAW-16 ARC YELLOW TEMPERA PAINT
Revision Date: 07/29/11
Page Number: lof 6
SECTION I – PRODUCT AND COMPANY INFORMATION
Product Name: WAW-16 ARC YELLOW TEMPERA PAINT
CAS Number MIXTURE
HMIS Rating: Health: 1 Fire: 1 Reactivity: 0
Company Identification: DAY-GLO COLOR CORP.

4515 SAINT CLAIR AVENUE

CLEVELAND OH 44103
Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name ARC YELLOW TEMPERA PAINT
Product Code WAW-16
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
4-AMINONAPHTHALENE- 1, 8-DICARBOXIMIDE 01742-95-6 < 1.0 SECTION II - HAZARDS IDENTIFICATION EYE CONTACT May cause irritation. SKIN CONTACT May cause irritation. INHALATION HAZARDS Outgassing of formaldehyde vapors can be irritating. INGESTION HAZARDS Small amounts swallowed are not likely to cause injury. Not a hazard in normal industrial use. TARGET ORGANS No organs affected. CANCER HAZARDS This product contains less than 0.1% free formaldehyde and may be capable of outgassing formaldehyde at levels in excess of OSHA's

MSDS Name: WAW-13 ROCKET RED TEMPERA PAINT
Revision Date: 07/29/11
Page Number: 1 of 6
SECTION I – PRODUCT AND COMPANY INFORMATION
Product Name: WAW-13 ROCKET RED TEMPERA PAINT
CAS Number MIXTURE
HMIS Rating: Health: 1 Fire: 1 Reactivity: 0
Company Identification: DAY-GLO COLOR CORP.

4515 SAINT CLAIR AVENUE

CLEVELAND OH 44103
Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name ROCKET RED TEMPERA PAINT
Product Code WAW-13
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
(No hazardous ingredients known at this time.)
SECTION III – HAZARDS IDENTIFICATION
EYE CONTACT
May cause irritation.
SKIN CONTACT
May cause irritation.
INHALATION HAZARDS
Outgassing of formaldehyde vapors can be irritating.
INGESTION HAZARDS
Small amounts swallowed are not likely to cause injury. Not a hazard
in normal industrial use.
TARGET ORGANS
No organs affected.
CANCER HAZARDS
This product contains less than 0.1% free formaldehyde and may be
capable of outgassing formaldehyde at levels in excess of OSHA’s
Action Level under some conditions of use. Formaldehyde is a known

4515 SAINT CLAIR AVENUE
CLEVELAND OH 44103

Telephone/Fax: (216) 391-7070 (216) 391-7751
Chemtrec (24 hr. Emergency) (800) 424-9300
Product Class WATER BASED PAINT
Trade Name AURORA PINK TEMPERA PAINT
Product Code WAW-11
SECTION II – INGREDIENT AND HAZARD INFORMATION
Ingredient Name CAS Number Percent
(No hazardous ingredients known at this time.)
SECTION III – HAZARDS IDENTIFICATION
EYE CONTACT
May cause irritation.
SKIN CONTACT
May cause irritation.
INHALATION HAZARDS
Outgassing of formaldehyde vapors can be irritating.
INGESTION HAZARDS
Small amounts swallowed are not likely to cause injury. Not a hazard
in normal industrial use.
TARGET ORGANS
No organs affected.
CANCER HAZARDS
This product contains less than 0.1% free formaldehyde and may be
capable of outgassing formaldehyde at levels in excess of OSHA’s
Action Level under some conditions of use. Formaldehyde is a known
cancer hazard. Long term exposure may result in dermatitis or res-

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
Precautionary Statements – Prevention
Wash face, hands and any exposed skin thoroughly after handling
Wear eye protection/ face protection
Precautionary Statements – Response
IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing
If eye irritation persists: Get medical advice/attention
2.3. Other Hazards Hazards not otherwise classified (HNOC)
Not Applicable
2.4 Other information
Not Applicable
Unknown Acute Toxicity 15.138% of the mixture consists of ingredient(s) of unknown toxicity
3. Composition/Information on Ingredients
Substance
Mixture
Chemical Name CAS No. Weight-%
Propylene glycol 57-55-6 1 – 5
C.I. Basic Violet 11:1 (tetrachlorozincate) 73398-89-7 1 – 5
The exact percentage (concentration) of composition has been withheld as a trade secret.
4. First aid measures
4.1 Description of first-aid measures
General advice No information available.
Eye contact Immediately flush with plenty of water. After initial flushing, remove any contact lenses and
continue flushing for at least 15 minutes. Keep eye wide open while rinsing. If symptoms
persist, call a physician.
Skin contact Wash off immediately with plenty of water for at least 15 minutes. Consult a physician if
necessary.
Inhalation Move to fresh air. If symptoms persist, call a physician.
Ingestion Do NOT induce vomiting. Drink plenty of water. Consult a physician.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms See Section 2.2, Label Elements and/or Section 11, Toxicological effects.
4.3 Indication of any immediate medical attention and special treatment needed
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 2 / 8

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
Notes to physician Treat symptomatically.
5. Fire-Fighting Measures
5.1 Extinguishing media
Suitable extinguishing media
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable Extinguishing Media None.
5.2 Special hazards arising from the substance or mixture
Special Hazard
Immediately place absorbent material in a sealed water-filled metal container to avoid spontaneous combustion of absorbent
material contaminated with this product.
Hazardous Combustion ProductsCarbon oxides. Nitrogen oxides (NOx).
Explosion Data
Sensitivity to Mechanical ImpactNone.
Sensitivity to Static DischargeNone.
5.3 Advice for firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. Accidental Release Measures
6.1 Personal precautions, protective equipment and emergency procedures
Ensure adequate ventilation, especially in confined areas. Use personal protective equipment.
6.2 Environmental precautions
Prevent product from entering drains.
6.3 Methods and materials for containment and cleaning up
Methods for Containment Dike to collect large liquid spills. Absorb with earth, sand or other non-combustible material
and transfer to containers for later disposal.
Methods for cleaning up Soak up with inert absorbent material. Keep in suitable and closed containers for disposal.
7. Handling and storage
7.1 Precautions for safe handling
Hygiene measures When using, do not eat, drink or smoke. Handle in accordance with good industrial hygiene
and safety practice.
7.2 Conditions for safe storage, including any incompatibilities
Storage Conditions Keep from freezing.
Materials to Avoid No materials to be especially mentioned.
8. Exposure controls/personal protection
8.1 Exposure Guidelines
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 3 / 8

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
Chemical Name ACGIH TLV OSHA PEL British Columbia Alberta Quebec Ontario TWAEV
Propylene glycol
57-55-6
– – TWA: 10 mg/m
3
TWA: 50 ppm
TWA: 155 mg/m
3
8.2 Appropriate engineering controls
Engineering Measures Showers
Eyewash stations
Ventilation systems.
8.3 Individual protection measures, such as personal protective equipment
Eye/Face Protection Safety glasses with side-shields.
Skin and body protection Wear chemical resistant footwear and clothing such as gloves, an apron or a whole body
suit as appropriate.
Respiratory protection . NIOSH/MSHA approved respiratory protection should be worn if exposure is anticipated.
Hygiene measures See section 7 for more information
10. Stability and Reactivity
10.1 Reactivity
9. Physical and chemical properties
9.1 Information on basic physical and chemical properties
Physical state Liquid
9.2 Other information
Volatile organic compounds (VOC)
content
22 g/L
Appearance Liquid Color Purple
Odor Pungent Odor Threshold No information available
Property Values Remarks Methods
pH No information available
Melting/freezing point No information available
Boiling point/boiling range > 100 C / 212 F
Flash Point > 94 C / > 201 F
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability Limits in Air
upper flammability limit No information available
lower flammability limit No information available
Vapor pressure No information available
Vapor density No information available
Specific Gravity 1.19
Water solubility Not Applicable
Solubility in other solvents No information available
Partition coefficient No information available
Autoignition temperature No information available
Decomposition temperature No information available
Viscosity, kinematic No information available
Viscosity, dynamic No information available
Explosive properties No information available
Oxidizing Properties No information available
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 4 / 8

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
No dangerous reaction known under conditions of normal use
10.2 Chemical stability
Stable
10.3 Possibility of hazardous reactions
None under normal processing.
10.4 Conditions to Avoid
Heat (temperatures above flash point), sparks, ignition points, flames, static electricity.
10.5 Incompatible Materials
None known based on information supplied.
10.6 Hazardous Decomposition Products
None known based on information supplied.
11. Toxicological information
11.1 Acute toxicity
Numerical measures of toxicity: Product Information
The following values are calculated based on chapter 3.1 of the GHS document
Unknown Acute Toxicity 15.138% of the mixture consists of ingredient(s) of unknown toxicity
Oral LD50 35,859.00 mg/kg
LC50 (Dust/Mist) 59.53 mg/l
Numerical measures of toxicity: Component Information
Chemical Name LD50 Oral LD50 Dermal LC50 Inhalation
Propylene glycol
57-55-6
20000 mg/kg ( Rat ) = 20800 mg/kg ( Rabbit ) –
C.I. Basic Violet 11:1
(tetrachlorozincate)
73398-89-7
220 mg/kg ( Rat ) – 0.83 mg/l (4 hour)
11.2 Information on toxicological effects
Skin corrosion/irritation
Product Information
May cause irritation
Component Information
No information available
Serious eye damage/eye irritation
Product Information
Irritating to eyes
Component Information
No information available
Respiratory or skin sensitization
Product Information
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 5 / 8
No information available

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
Component Information
No information available
Germ cell mutagenicity
Product Information
No information available
Component Information
No information available
Carcinogenicity
Product Information
No information available
Component Information
No information available
Reproductive toxicity
Product Information
No information available
Component Information
No information available
STOT – single exposure
No information available
STOT – repeated exposure
No information available
Other adverse effects
Product Information
No information available
Component Information
No information available
Aspiration hazard
Product Information
No information available
Component Information
No information available
12. Ecological information
12.1 Toxicity
Ecotoxicity No information available
15.97663 % of the mixture consists of components(s) of unknown hazards to the aquatic environment
Ecotoxicity effects
Chemical Name Toxicity to algae Toxicity to fish Toxicity to daphnia and other
aquatic invertebrates
Propylene glycol
57-55-6
EC50: 96 h Pseudokirchneriella
subcapitata 19000 mg/L
LC50: 96 h Oncorhynchus mykiss
51600 mg/L static LC50: 96 h
Oncorhynchus mykiss 41 – 47 mL/L
static LC50: 96 h Pimephales
promelas 51400 mg/L static LC50:
96 h Pimephales promelas 710
mg/L
EC50: 48 h Daphnia magna 1000
mg/L Static
12.2 Persistence and degradability
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 6 / 8
No information available.

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
12.3 Bioaccumulative potential
Discharge into the environment must be avoided
12.4 Mobility in soil
No information available.
12.5 Other adverse effects
No information available
13. Disposal Considerations
13.1 Waste treatment methods
Dispose of in accordance with federal, state, and local regulations.
14. Transport Information
DOT Not regulated
MEX Not regulated
IMDG Not regulated
IATA Not regulated
15. Regulatory information
15.1 International Inventories
TSCA Complies
DSL –
EINECS/ELINCS –
ENCS –
IECSC –
KECL –
PICCS –
AICS –
NZIoC –
TSCA – United States Toxic Substances Control Act Section 8(b) Inventory
DSL – Canadian Domestic Substances List
EINECS/ELINCS – European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
ENCS – Japan Existing and New Chemical Substances
IECSC – China Inventory of Existing Chemical Substances
KECL – Korean Existing and Evaluated Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
AICS – Australian Inventory of Chemical Substances
NZIoC – New Zealand Inventory of Chemicals
15.2 U.S. Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product contains a chemical
or chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372:
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 7 / 8

_____________________________________________________________________________________________
SRX-20 – Screamin’ Ultra Violet Paint Revision Date 09-Aug-2018
Chemical Name SARA 313 – Threshold Values % Weight-%
C.I. Basic Violet 11:1 (tetrachlorozincate)
73398-89-7
1.0 1 – 5
15.3 Pesticide Information
Not applicable
15.4 U.S. State Regulations
California Proposition 65
This product contains the following Proposition 65 chemicals:
Chemical Name California Prop. 65
C.I. Basic Violet 10 – 81-88-9 Carcinogen
16. Other information
Legend:
ACGIH (American Conference of Governmental Industrial Hygienists)
Ceiling (C)
DOT (Department of Transportation)
EPA (Environmental Protection Agency)
IARC (International Agency for Research on Cancer)
International Air Transport Association (IATA)
International Maritime Dangerous Goods (IMDG)
NIOSH (National Institute for Occupational Safety and Health)
NTP (National Toxicology Program)
OSHA (Occupational Safety and Health Administration of the US Department of Labor)
PEL (Permissible Exposure Limit)
Reportable Quantity (RQ)
Skin designation (S*)
STEL (Short Term Exposure Limit)
TLV (Threshold Limit Value)
TWA (time-weighted average)
Prepared By DayGlo Color Corp.
Regulatory Affairs/Product Safety
Revision Date 09-Aug-2018
Revision Note
No information available
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
End of Safety Data Sheet
NFPA Health Hazard – Flammability – Instability – Physical and chemical
hazards –
HMIS Health Hazard 2 Flammability 1 Physical Hazard 0
_____________________________________________________________________________________________
09-Aug-2018 – SRX-20 – 1.01 – AGHS – English – Page 8 / 8
Personal protection X

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
Not Applicable
Unknown Acute Toxicity 13.938% of the mixture consists of ingredient(s) of unknown toxicity
3. Composition/Information on Ingredients
Substance
Mixture
This material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200).
Chemical Name CAS No. Weight-%
Propylene glycol 57-55-6 1 – 5
The exact percentage (concentration) of composition has been withheld as a trade secret.
4. First aid measures
4.1 Description of first-aid measures
General advice No information available.
Eye contact Immediately flush with plenty of water. After initial flushing, remove any contact lenses and
continue flushing for at least 15 minutes. Keep eye wide open while rinsing. If symptoms
persist, call a physician.
Skin contact Wash off immediately with plenty of water for at least 15 minutes. Consult a physician if
necessary.
Inhalation Move to fresh air. If symptoms persist, call a physician.
Ingestion Do NOT induce vomiting. Drink plenty of water. Consult a physician.
4.2 Most important symptoms and effects, both acute and delayed
Symptoms See Section 2.2, Label Elements and/or Section 11, Toxicological effects.
4.3 Indication of any immediate medical attention and special treatment needed
Notes to physician Treat symptomatically.
5. Fire-Fighting Measures
5.1 Extinguishing media
Suitable extinguishing media
Use extinguishing measures that are appropriate to local circumstances and the surrounding environment.
Unsuitable Extinguishing Media None.
5.2 Special hazards arising from the substance or mixture
Special Hazard
None known based on information supplied.
Hazardous Combustion ProductsCarbon oxides. Nitrogen oxides (NOx).
Explosion Data
Sensitivity to Mechanical ImpactNone.
Sensitivity to Static DischargeNone.
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 2 / 8

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
5.3 Advice for firefighters
As in any fire, wear self-contained breathing apparatus pressure-demand, MSHA/NIOSH (approved or equivalent) and full
protective gear.
6. Accidental Release Measures
6.1 Personal precautions, protective equipment and emergency procedures
Ensure adequate ventilation, especially in confined areas. Use personal protective equipment.
6.2 Environmental precautions
Prevent product from entering drains.
6.3 Methods and materials for containment and cleaning up
Methods for Containment Dike to collect large liquid spills. Absorb with earth, sand or other non-combustible material
and transfer to containers for later disposal.
Methods for cleaning up Soak up with inert absorbent material. Keep in suitable and closed containers for disposal.
7. Handling and storage
7.1 Precautions for safe handling
Hygiene measures When using, do not eat, drink or smoke. Handle in accordance with good industrial hygiene
and safety practice.
7.2 Conditions for safe storage, including any incompatibilities
Storage Conditions Keep from freezing.
Materials to Avoid No materials to be especially mentioned.
8. Exposure controls/personal protection
8.1 Exposure Guidelines
Chemical Name ACGIH TLV OSHA PEL British Columbia Alberta Quebec Ontario TWAEV
Propylene glycol
57-55-6
– – TWA: 10 mg/m
3
TWA: 50 ppm
TWA: 155 mg/m
3
8.2 Appropriate engineering controls
Engineering Measures Showers
Eyewash stations
Ventilation systems.
8.3 Individual protection measures, such as personal protective equipment
Eye/Face Protection Safety glasses with side-shields.
Skin and body protection Wear chemical resistant footwear and clothing such as gloves, an apron or a whole body
suit as appropriate.
Respiratory protection . NIOSH/MSHA approved respiratory protection should be worn if exposure is anticipated.
Hygiene measures See section 7 for more information
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 3 / 8

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
10. Stability and Reactivity
10.1 Reactivity
No dangerous reaction known under conditions of normal use
10.2 Chemical stability
Stable
10.3 Possibility of hazardous reactions
None under normal processing.
10.4 Conditions to Avoid
Heat (temperatures above flash point), sparks, ignition points, flames, static electricity.
10.5 Incompatible Materials
None known based on information supplied.
10.6 Hazardous Decomposition Products
None known based on information supplied.
9. Physical and chemical properties
9.1 Information on basic physical and chemical properties
Physical state Liquid
9.2 Other information
Volatile organic compounds (VOC)
content
22 g/L
Appearance Liquid Color Green
Odor Pungent Odor Threshold No information available
Property Values Remarks Methods
pH No information available
Melting/freezing point No information available
Boiling point/boiling range > 100 C / 212 F
Flash Point > 94 C / > 201 F
Evaporation rate No information available
Flammability (solid, gas) No information available
Flammability Limits in Air
upper flammability limit No information available
lower flammability limit No information available
Vapor pressure No information available
Vapor density No information available
Specific Gravity 1.19
Water solubility Not Applicable
Solubility in other solvents No information available
Partition coefficient No information available
Autoignition temperature No information available
Decomposition temperature No information available
Viscosity, kinematic No information available
Viscosity, dynamic No information available
Explosive properties No information available
Oxidizing Properties No information available
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 4 / 8

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
11. Toxicological information
11.1 Acute toxicity
Numerical measures of toxicity: Product Information
Unknown Acute Toxicity 13.938% of the mixture consists of ingredient(s) of unknown toxicity
Numerical measures of toxicity: Component Information
Chemical Name LD50 Oral LD50 Dermal LC50 Inhalation
Propylene glycol
57-55-6
20000 mg/kg ( Rat ) = 20800 mg/kg ( Rabbit ) –
11.2 Information on toxicological effects
Skin corrosion/irritation
Product Information
May cause skin irritation
Component Information
No information available
Serious eye damage/eye irritation
Product Information
May cause eye irritation
Component Information
No information available
Respiratory or skin sensitization
Product Information
No information available
Component Information
No information available
Germ cell mutagenicity
Product Information
No information available
Component Information
No information available
Carcinogenicity
Product Information
No information available
Component Information
No information available
Reproductive toxicity
Product Information
No information available
Component Information
No information available
STOT – single exposure
No information available
STOT – repeated exposure
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 5 / 8
No information available

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
Other adverse effects
Product Information
No information available
Component Information
No information available
Aspiration hazard
Product Information
No information available
Component Information
No information available
12. Ecological information
12.1 Toxicity
Ecotoxicity No information available
15.83463 % of the mixture consists of components(s) of unknown hazards to the aquatic environment
Ecotoxicity effects
Chemical Name Toxicity to algae Toxicity to fish Toxicity to daphnia and other
aquatic invertebrates
Propylene glycol
57-55-6
EC50: 96 h Pseudokirchneriella
subcapitata 19000 mg/L
LC50: 96 h Oncorhynchus mykiss
51600 mg/L static LC50: 96 h
Oncorhynchus mykiss 41 – 47 mL/L
static LC50: 96 h Pimephales
promelas 51400 mg/L static LC50:
96 h Pimephales promelas 710
mg/L
EC50: 48 h Daphnia magna 1000
mg/L Static
12.2 Persistence and degradability
No information available.
12.3 Bioaccumulative potential
Discharge into the environment must be avoided
12.4 Mobility in soil
No information available.
12.5 Other adverse effects
No information available
13. Disposal Considerations
13.1 Waste treatment methods
Dispose of in accordance with federal, state, and local regulations.
14. Transport Information
DOT Not regulated
MEX Not regulated
IMDG Not regulated
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 6 / 8

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
IATA Not regulated
15. Regulatory information
15.1 International Inventories
TSCA Complies
DSL –
EINECS/ELINCS –
ENCS –
IECSC –
KECL –
PICCS –
AICS –
NZIoC –
TSCA – United States Toxic Substances Control Act Section 8(b) Inventory
DSL – Canadian Domestic Substances List
EINECS/ELINCS – European Inventory of Existing Chemical Substances/European List of Notified Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
ENCS – Japan Existing and New Chemical Substances
IECSC – China Inventory of Existing Chemical Substances
KECL – Korean Existing and Evaluated Chemical Substances
PICCS – Philippines Inventory of Chemicals and Chemical Substances
AICS – Australian Inventory of Chemical Substances
NZIoC – New Zealand Inventory of Chemicals
15.2 U.S. Federal Regulations
SARA 313
Section 313 of Title III of the Superfund Amendments and Reauthorization Act of 1986 (SARA). This product does not contain any
chemicals which are subject to the reporting requirements of the Act and Title 40 of the Code of Federal Regulations, Part 372
15.3 Pesticide Information
Not applicable
15.4 U.S. State Regulations
California Proposition 65
This product does not contain any Proposition 65 chemicals
16. Other information
Legend:
ACGIH (American Conference of Governmental Industrial Hygienists)
Ceiling (C)
DOT (Department of Transportation)
EPA (Environmental Protection Agency)
IARC (International Agency for Research on Cancer)
International Air Transport Association (IATA)
International Maritime Dangerous Goods (IMDG)
NIOSH (National Institute for Occupational Safety and Health)
NTP (National Toxicology Program)
OSHA (Occupational Safety and Health Administration of the US Department of Labor)
NFPA Health Hazard – Flammability – Instability – Physical and chemical
hazards –
HMIS Health Hazard 1 Flammability 1 Physical Hazard 0 Personal protection X
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 7 / 8

_____________________________________________________________________________________________
SRX-18 – Screamin Signal Green Paint Revision Date 09-Aug-2018
PEL (Permissible Exposure Limit)
Reportable Quantity (RQ)
Skin designation (S*)
STEL (Short Term Exposure Limit)
TLV (Threshold Limit Value)
TWA (time-weighted average)
Prepared By DayGlo Color Corp.
Regulatory Affairs/Product Safety
Revision Date 09-Aug-2018
Revision Note
No information available
Disclaimer
The information provided in this Safety Data Sheet is correct to the best of our knowledge, information and belief at the
date of its publication. The information given is designed only as a guidance for safe handling, use, processing, storage,
transportation, disposal and release and is not to be considered a warranty or quality specification. The information
relates only to the specific material designated and may not be valid for such material used in combination with any other
materials or in any process, unless specified in the text.
End of Safety Data Sheet
_____________________________________________________________________________________________
09-Aug-2018 – SRX-18 – 1.01 – AGHS – English – Page 8 / 8