PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM

DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.

PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM

DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.

Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, starting with one ounce per quart.
(1) Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2) If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3) Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand the material is outdated and should be replaced with new product.

Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our products before use and
satisfy themselves as to contents and suitability. All claim requests must be made in writing and are subject to review, including storage temperature
verification and retain evaluations. The exclusive remedy for all proven claims is replacement of our materials. In no event shall we be liable for special,
incidental or consequential damages, including damages caused in transit (exworks terms). Nothing herein shall constitute a warranty, expressed or
implied, including any warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent and trademark rights
reserved.
www.hawkeyeind.com
DURATEC REDUCER
USE GUIDE
WWW.HAWKEYEIND.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316
Problem Solution

blended with Duratec products.

Cold thinner

Failure to rapidly mix
into Duratec products
Cause
DURATEC REDUCER
TROUBLESHOOTING

PRODUCT # 39UCE
SAFETY & HANDLING
Duratec Reducer is extremely flammable. Do not apply near sparks, open flames
or heat. Keep area ventilated. Do not smoke. Avoid continuous breathing of vapor.
Duratec Reducer contains ingredients which could be harmful if mishandled.
Contact with skin and eyes should be avoided and necessary protective equipment
and clothing should be worn. Individuals should wash with soap and water before
eating or drinking. All containers should be properly labeled to prevent accidental
ingestion or improper disposal. Individuals should reseal any partly used material
back in the container. Store under cool, dry conditions and away from open flames
and high temperatures.
For more detailed instructions on storage, please see the MSDS sheet.
DESCRIPTION
909-546-1160
hawkeyesales@hawkeyeind.com
PO BOX 415,
BLOOMINGTON, CA 92316
WWW.DURATEC1.COM

DURATEC REDUCER
USE GUIDE | PRODUCT #39UCE
Limited/ warranty statement: Our products are intended for sale to industrial and commercial customers. We request that customers inspect and test our
products before use and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any
warranty of merchantability or fitness, nor is protection from any law or patent to be inferred. All patent rights are reserved. The exclusive remedy for all
proven claims is replacement of our materials and in no event shall we be liable for special, incidental or consequential damages.
WWW.DURATEC1.COM 909-546-1160 HAWKEYESALES@HAWKEYEIND.COM PO BOX 415, BLOOMINGTON, CA 92316www.duratec1.com
Use Instructions
Duratec products are manufactured to be used as is, directly out of the can. The right step may
be
adjusting your spray equipment tip size, rather than reducing the material.
However there are times reducing is necessary. In those situations we advocate reducing as
little as possible, start
ing with one ounce per quart.
(1)Thoroughly mix the Duratec product you plan to use. Most Duratec products require a
thorough mix for the product to be consistent. A paint shaker or drill mixer is best.
(2)If the viscosity of the Duratec is too high for spraying, add one ounce of Duratec Reducer per
quart. Mix and evaluate the viscosity. Usually no more than three ounces of Duratec Reducer are
necessary per quart.
(3)Catalyze and spray the Duratec once the desired result viscosity is achieved. For specific catalyst
information, please consult the Technical Data Sheet (TDS) of the Duratec product you are using.
FYI: Duratec Reducer 39UCE was formerly known as Duratec Thinner 39LAC-3. If you have material
labeled as 39LAC-3 on hand it is likely the product is outdated. Please reach out to our team.
DURATEC REDUCER
T
ROUBLESHOOTING | PRODUC T # 39UCE
Problem Cause Solution
Cold thinner
Warm thinner and/or Duratec product.
Failure to rapidly mix
into Duratec products
Continue to machine mix until fully
blended with Duratec products.

DURA TECHNOLOGIES
39SURF103 & 39SURF102
World Class Coatings
Technology GEL COAT SURFACING
ADDITIVE
____________________________________________________________________________________________

DURA TECHNOLOGIES, INC. 10% Surfacing Agent is manufactured using high
quality materials and tight production controls. The wax used in this product is the best
available 125 F surfacing wax currently on the market. This material is frequently used
for gel coat repairs and for corrosion resistant hot coats where it is necessary to have a well
cured non-air inhibited surface

Coating Characteristics:

weight per gallon 7.35 lbs
V.O.C. 786 grams/liter
Shelf Life 6 months

Film Characteristics:

Melting point 125 F

Application:

1. 39SURF103 and 39SURF102 Surfacing Agent is ready to use as received.
2. If there is a trace of haze or surfacing wax on the surfacing agent warm it with hot
water to about 80 F until the turbidity disappears.
3. Add 2 percent by weight surfacing agent to the resin or gel coat to be air cured and
thoroughly mix before using.
4. Catalyze the resin or gel coat as recommended by the manufacturer and apply as
desired.

WARNING:
Once the surfacing agent is added to a material, that material can not be top coated
unless the surface is sanded until all of the wax is completely removed.

Disclaimer:
The information included in this technical bulletin is believed to be accurate and representative of
the product in general but is not a certification of any specific batch. This bulletin is provide as a
service and is not intended as a specification or as a warranty of performance.

DURA TECHNOLOGIES
39SURF103 & 39SURF102
World Class Coatings
Technology GEL COAT SURFACING
ADDITIVE
____________________________________________________________________________________________

DURA TECHNOLOGIES, INC. 10% Surfacing Agent is manufactured using high
quality materials and tight production controls. The wax used in this product is the best
available 125 F surfacing wax currently on the market. This material is frequently used
for gel coat repairs and for corrosion resistant hot coats where it is necessary to have a well
cured non-air inhibited surface

Coating Characteristics:

weight per gallon 7.35 lbs
V.O.C. 786 grams/liter
Shelf Life 6 months

Film Characteristics:

Melting point 125 F

Application:

1. 39SURF103 and 39SURF102 Surfacing Agent is ready to use as received.
2. If there is a trace of haze or surfacing wax on the surfacing agent warm it with hot
water to about 80 F until the turbidity disappears.
3. Add 2 percent by weight surfacing agent to the resin or gel coat to be air cured and
thoroughly mix before using.
4. Catalyze the resin or gel coat as recommended by the manufacturer and apply as
desired.

WARNING:
Once the surfacing agent is added to a material, that material can not be top coated
unless the surface is sanded until all of the wax is completely removed.

Disclaimer:
The information included in this technical bulletin is believed to be accurate and representative of
the product in general but is not a certification of any specific batch. This bulletin is provide as a
service and is not intended as a specification or as a warranty of performance.

Technical Data Sheet

Odorless Mineral Spirits

Test Unit Method Min Max Qualitative
Aromatics ppm ASTM E-169 – 1000 –
Distillation DP FAH ASTM D-86 – 395 –
Distillation, IBP FAH ASTM D-86 330 – –
Flash Point, TCC FAH ASTM D-56 115 – –
Odor – Smell – – Pass
Saybolt Color SAY ASTM D-6045 30 – –
Specific Gravity 60/60 F – ASTM D4052 0.740 0.770 –

These specifications are typical and represent the quality of our product in general. The information
herein is to assist customers in determining whether out product is suitable for their applications. Our
product is intended for sale to industrial and commercial customers. We recommend that customers inspect
and test our products before use and satisfy themselves as to content and suitability. We warrant that our
products will meet our written specification. Nothing herein shall constitute any other warranty expressed
or implied, including any warranty of merchantability or fitness, nor is protection from any law or patent
to be inferred. Health and safety information, as well as safe handling instructions are available through
our Safety Data Sheet for this product. For more information about our products, please call (323)245-
2345.

Chemical Distributor
P.O. Box 39524
4578 Brazil Street
Los Angeles, CA 90039
Tel: (323) 245-2345
(818) 242-8486
Fax (818) 242-7804
www.aglayne.com

Mineral Spirits

Property Units Limits Results Method
Purity
Appearance
Color Saybolt >28 30
PH
Water
Density @ 15.6C API 43.2 57.5 54.3 ASTM D 4052

Disclaimer: These specifications represent the quality of our product in general
and may vary from batch to batch and producer to producer. If you are looking
for particular specifications please call our office or email your representative.

Shell Oil and Chemical Distributor
P.O. Box 39524
4578 Brazil Street
Los Angeles, CA 90039
Tel: (323) 245-2345
(818) 242-8486
Fax (818) 242-7804
www.aglayne.com

COR50-ZZ-00805 is methyl methacrylate monomer (MMA). MMA is a colorless liquid for industrial use primarily as a
reactive solvent (diluent) for polymerization. MMA contains a small amount of stabilizing inhibitor to prevent premature
polymerization.

APPLICATION TYPICAL PROPERTIES
Colorless industrial reactive diluent for polymerization Methyl Methacrylate
Viscosity 0.53 cPs
APHA Color, maximum 10
Specific Gravity, 25 C 0.939
Flash Point, C 10

COR50-ZZ-00805
Reactive Diluent Solution
Technical Data Sheet

COR50-ZZ-00805 is methyl methacrylate monomer (MMA). MMA is a colorless liquid for industrial use primarily as a
reactive solvent (diluent) for polymerization. MMA contains a small amount of stabilizing inhibitor to prevent premature
polymerization.

APPLICATION TYPICAL PROPERTIES
Colorless industrial reactive diluent for polymerization Methyl Methacrylate
Viscosity 0.53 cPs
APHA Color, maximum 10
Specific Gravity, 25 C 0.939
Flash Point, C 10

COR50-ZZ-00805
Reactive Diluent Solution
Technical Data Sheet

COR50-ZZ-00805 is methyl methacrylate monomer (MMA). MMA is a colorless liquid for industrial use primarily as a
reactive solvent (diluent) for polymerization. MMA contains a small amount of stabilizing inhibitor to prevent premature
polymerization.

APPLICATION TYPICAL PROPERTIES
Colorless industrial reactive diluent for polymerization Methyl Methacrylate
Viscosity 0.53 cPs
APHA Color, maximum 10
Specific Gravity, 25 C 0.939
Flash Point, C 10

COR50-ZZ-00805
Reactive Diluent Solution
Technical Data Sheet