SHOP/MFG SUPPLIES/FLM | Revchem Composites

38SQUEE-36_TDS.pdf

Sat, 27 Sep 2025 10:07:08 +0000

22695 Old Canal Road, Yorba Linda, CA 92887 p 714.279.9928 f 714.279.0307

MATERIAL SPECIFICATION

To: Revchem Bloomington
2720 S. Willow Ave
Bloomington, CA 92316
Attn: Russ Tell

Part Number 564381
Part Description 35.5 Rubber Squeegee

Material Natural Rubber
Tensile 1160 psi
Elongation 200%
Hardness 70-75 Shore A
Compression Set 50% max

Heat aged, test method D573, 70 hours at 70 C
Change in tensile strenth +/-30%
Change in elongation -50% max
Change in hardness +/-15 points

Pacifictech Molded Products, Inc. Date: February 10, 2025

38PRIMER6_TDS.pdf

Sat, 27 Sep 2025 10:07:07 +0000

Property
Test
Method
Value
Uncured Product
23 +/- 2 C and 50 +/-5% humidity
Color Pale Yellow
Cure Profile
23+/-2 C and 50+/-5%
humidity
Density
BS ISO
2781
0.83 g/cm3
Flash Point C
BS 2000-
34
28 C
Odour Alcohol
Rheology Liquid
Tack Free Time / Skin
Formation at 23 C/73 F
15 min
Viscosity Mixed Brookfield1 cP
Storage
Max Storage Temperature 25 C / 77 F
Min Storage Temperature 5 C / 41 F
Shelf Life 18 mths
Primer No. 6
Primer
Description
This is a specially formulated silicone based primer for use with a
wide range of CHT 1K Condensation / Moisture curing RTV
silicone sealants. This primer imparts good adhesion to most
metals. It is recommended as a primer for use on non-porous
surfaces. For all new applications, it is recommended that
customers carry out small-scale tests to determine the suitability
of the primer and the strength of bond produced.
Key Features
Aerospace approved
Suitable for use with CHT adhesives
Suitable for non porous surfaces
For use with most metals
Key Applications
Rolls Royce MSRR1064
Application
Primer for condensation cure 1 part adhesives on metal
substrates. Not suitable for polycarbonate and acrylic
Use and Cure Information
This primer contains solvents which are classified as hazardous
under current regulations. Users should read the Safety Data
Sheets for this product carefully before use. Surfaces to be
bonded should be dry and free from grease, oil, dust and release
agents. Non-porous substrates, should be solvent degreased prior to application. The primer should be applied with a lint-free cloth or
paintbrush and allowed to dry thoroughly at room temperature for a minimum time equal to the tack free time given in this document, before
applying the sealant. Drying should be carried out in a well-ventilated area. Do not leave longer than 2 hours. The drying/curing time is
dependent on the ambient temperature and humidity. Heat should not be applied to accelerate the drying cycle. Over-application of the
primer will result in poor adhesion. As a guide, one litre of Primer should be sufficient for approximately 15 m . It is absolutely important to
check the compatibility in preliminary tests if unknown substrates are used.
Health & Safety
Safety
Please observe the safety data sheets and the safety statements on the container labels when handling our products. The dangerous goods
regulations and the accident prevention regulations of the professional associations must be particularly observed. Keep the safety data
sheet of the applied product at hand since it provides useful instructions for the safe use and disposal of the product as well as for actions to
be taken in case of accidents.
Revision Date 01 Mar 2024
Revision No 2
Download Date 22 Oct 2024
TECHNICAL DATA SHEET
The content set out in the technical data sheet does not contain information upon which you should rely. It is provided for general information purposes only and does not constitute a product
specification. You must obtain professional or specialist advice before taking any action based on the information provided in the technical data sheet.
CHT make reasonable efforts to ensure that information set out in the technical data sheet is complete, accurate, and up-to-date. CHT do not, however, make any representations, warranties or
guarantees (whether express or implied) that information set out in the technical data sheet is complete, accurate, or up-to-date or that the product will be suitable for your requirements. You
should carry out your own testing to determine the applicability of such information and whether the product will be suitable. CHT reserve the right to modify the technical data sheet at any time.
The CHT technical service department is available to offer further information and advice and should it be needed to look at modifying current products or custom formulate a new one to meet
your specific requirements. Please contact the technical service department.
CHT Germany GmbH: Postfach 12 80, 72002 T bingen, Bismarckstra e 102, 72072 T bingen, Germany
Telephone: 07071/154-0, Fax: 07071/154-290, Email: info@cht.com, Homepage: www.cht.com / www.cht-silicones.com

38MYLARA_TDS.pdf

Sat, 27 Sep 2025 10:07:06 +0000

WA ISO 9001:2008 Ya
7 ranscendia Certiec Compary emt
DESCRIPTION:
Oriented Polyester films are rigid plastics that are strong, smooth to matte surfaces. Available in sheets and rolls
durable, dimensionally stable, and have anti-curl with widths from .5″ to 92″ with 3″, 6″, and 10″ cores.
properties. They are suitable for graphics, packaging, Gauges are available from .00032″ to .014″, and special
electrical and industrial applications. Oriented Polyester surface treatments include ink adhesion, slip, and anti-
films are available in super-clear to clear matte, and static.
CHARACTERISTICS:
* Easily printed with water or solvent based inks using * Excellent chemical and abrasion resistance and
flexography, offset lithography, and screen printing. temperature resistance.
* Can be folded, sheeted, die cut, grommeted, glued, * General inertness and free of additives.
and sewn.
TECHNICAL DATA:
MECHANICAL PROPERTIES TYPICAL VALUES TEST CONDITIONS TEST METHOD-ASTM
MD >20 kg/mm?
TENSILE STRENGTH TD 320 kg/mm? 25 C D-882-64
MD 100 to 120%
ELONGATION AT BREAK 882-1
TD 100 to 120% esr D-882-84
2
F-5 VALUE MD 9.5 kg/mm 25 C D-882-64
TD 9.5 kg/mm?
IMPACT STRENGTH 400 g cm/cm? 25 C. 2541 film D-1709-62
TEAR STRENGTH – PROPAGATING 20 g/mil 25 C. 2541 film D-1922-61
ELMENDOPF INITIAL – GRAVES 800 g/mil 25 C. 254 film _ D-1004-66
BURSTING STRENGTH >5 kg/cm? 25 C. 2541 film D-774-63
FOLDING ENDURANCE 10 cycle 25 C. 25,1 film D-2176-63
PHYSICAL PROPERTIES
DENSITY 1.390 to 1.405 g/cm? 25 C D-1505-63
MOISTURE ABSORPTION .05 wt% 23 C, 24 hr D-570-63
WATER VAPOR 25 g/m*/24 hr 251 film @ 40 C. @ 100% R.H. E-98-66
TRANSMISSION RATE: OXYGEN 40 cm*/m#/24 hr 25u film @ 25 C.@ 1 atm D-1434-66
COEFFICIENT OF KINETIC 5
FRICTION: FILM/FILM STATIC OF 03 1008 ere D-1894-68
THERMAL PROPERTIES
MELTING POINT 280 C
SOFTENING POINT 250 C
HEAT SHRINKAGE 2.0 % 150 C X 30 min D-2305-67
SERVICE TEMPERATURE -70 to +150 C
SPECIFIC HEAT 0.3 cal g C 25 C
COEFFICIENT OF LINEAR THERMAL EXPANSION 3×10 cm/em/ C 30 C to 50 C D-696-44
COEFFICIENT OF THERMAL CONDUCTIVITY 3×10″ cal/om sec C
ELECTRICAL PROPERTIES
DIELECTRIC STRENGTH 7,500 volts/mil 25 C 60hz D-149-64
DIELECTRIC CONSTANT 33 25 C 60hz D-150-65
DIELECTRIC DISSIPATION 0.0025 25 C 60hz D-150-65
VOLUME RESISTIVITY 10 ohm-cm 25 C D-257-66 & D-2305-67
SURFACE RESISTIVITY 10″? ohm-cm/cm 23 C 80% RH. D-257-66
Note: The stated values are typical data and are not specification of guarantee. Transcendia suggests that purchaser confirm product compatibility prior to use of this product .
Stated values are believed to be accurate, but all information is presented without guarantee or responsibility on the part of Transcendia.
CORPORATE HEADQUARTERS 9201 W. Belmont Avenue | Franklin Park, IL 60131
USA 800.618.5060 | 847.678.1800 main | 847.233.0199 fax
CAN 800.268.4108 | 416.292.6000 main | 416.292.7399 fax
TRANSCENDIA.COM 2016 Transcendia Inc. All Rights Reserved.

38MS242N_TDS.pdf

Sat, 27 Sep 2025 10:07:05 +0000

For technical information call 800.992.2424 or 203.743.4447
For product sales: CT 800.442.3424, CA 800.771.8161, IL 800.447.4866, Canada 800.307.2199
www.miller-stephenson.com

MS-242N
Quik-Freeze

Description
Miller-Stephenson s Quik-Freeze

(MS-242N) is a 14oz
aerosol product that is designed for convenient use in
many industrial applications. It contains HFC 134a
propellant which is a non-ozone depleting chemical.

MS-242N provides a rapid method of cooling small
electronic components. This product is utilized to locate
intermittent malfunctions in electronic equipment.
Applying the Quik-Freeze

will have no effect on
components operating properly but faulty components will
be shocked into failure mode and immediately identified.

MS-242N freezes small areas to -55 F/-48 C.

ADVANTAGES:

Nonconductive
Nonflammable
Odorless
Low order of toxicity
Compatible with most plastics, elastomers, and
metals
Leaves no residue
NSN 6850-01-333-1841

Quik-Freeze

is recommended for:

Heat-cold intermittence testing of electronic
components.
Protection of expensive components during
soldering/desoldering.
Low temperature circuit testing.
Nondestructive testing of electronic and
electromechanical systems.

PHYSICAL PROPERTIES OF HFC 134a:

Molecular weight .. 102.03
Boiling point ..-15.7 F/-26.5 C
Vapor pressure 96.5 psia @ 77 F/25 C
Density .. .1.21 @ 77 F/25 C
VOC . exempt
ODP .. .zero

Safety Data Sheet (SDS) is available upon request

1308-9K

The recommendation made here with and the information set forth with respect to the
performance or use of our products are believed, but not warranted to be accurate. The products
discussed are sold without warranty, as to fitness or performance, express or implied and upon
condition that purchasers shall make their own test to determine suitability of such products for
their particular purposes. Likewise, statements concerning the possible uses of our products are
not intended as recommendations to use our products in the infringement of any patent.

38FP5_TDS.pdf

Sat, 27 Sep 2025 10:07:03 +0000

Komar
| Alliance
Threads, Papers, Chemicals and Supplies
REINFORCED ASPHALTIC KRAFT 3560
Technical Data Sheet
Composition
| Kraft Paper (Top Sheet) Natural Recycled Kraft 30,0#/3000 Sq. Ft.
shat ORTHO F
110 1/0 Denier 1-1-1
MD Reinforcement Fiberglass | 1.094/3000 $9, Ft.
CD Reinforcement Fiberglass BaD Retietion: Ls scars
1.37#/3000 Sq, Ft.
Physical Properties
Basset
Ba
Tensile Strength ASTM D-828 58 Ibs/in MD
a
The technical data presented in this Technical Data Sheet are typical physical properties observed. and
recorded, not limiting technical specifications. These values can range and data is an observed average
for Informational purposes. Physical properties listed above are based upon statistical averages. Values
for weights and caliper can vary + 10%
6900 Washington Blvd. – Montebello, CA 90640
(800) 872-7397 www.komar.com Fax (323) 890-3003

38FILTPA723_TDS.pdf

Sat, 27 Sep 2025 10:07:03 +0000

Filter :
fc : PRODUCT SPECIFICATION SHEET
MODEL: PA15 standararinersiass media
_ Weight of 15 GRAMS/SQ.FT.
Ideal for use in a variety of crossdraft applications.
98.66% average spray removal efficiency.
ie __ -Meets the testing and performance requirements of NESHAP 40CFR63 Subpart 6H.***
pan fn
| -Initial pressure drop of .02 @ 150 FPM.
-Paint holding capacity of 1.3 LBS/SQ.FT. of media.
-Rated UL 900 for flammability.
-Thermally stable to 212 degrees F.
-Typically land-fillable (contains no known hazardous materials).
-Compression rolled and packed to reduce storage and shipping/handling costs.
-Available in rolls, or cut pads.
PAINT OVERSPRAY REMOVAL EFFICIENCY %
0 _ ___ __ _ ___
es ee ee eee |
dt a PAINT OVERSPRAY REMOVAL EFFICIENCY % i =|
Soave -)
5 9. – – <== fi a | 400 500 750 2000 me es | WEIGHT PAINT FED (grams) _ S| pees 7 ctual test report available upon request. <->
Distributed by: – yas :
eect +>
tencealen GA 5a504 a
Fitten TEL: 600.5404 AIR Bs: es:
Systems. FAX; 805-981-8675 ae
E-MAIL: sales@filtersystemsusa.com poe
WEB: wwwfiltersystemsusa.com . ae

38FILTPA22B_TDS.pdf

Sat, 27 Sep 2025 10:07:00 +0000

Syetems )) PRODUCT SPECIFICATION SHEET
MODEL: PAZ2 Heavy puty Fiterstass Media
__ Weight of 22 GRAMS/SQ.FT.
__-Idea for use in a variety of crossdraft/downdraft spraybooth applications.
-99.389 f average spray removal efficiency.
__-Meets the testing and performance requirements of NESHAP 40CFR63 Subpart 6H.***
oe Anita pressure drop of .03 @ 150 FPM.
__ -Paint holding capacity of 1 LBS/SQ.FT. of media.
___ -Rated UL 900 for flammability.
Thermally stable to 212 degrees F.
E -Typically land-fillable (contains no known hazardous materials).
f -Compression rolled and packed to reduce storage and shipping/handling costs.
i -Available in rolls, or cut pads.
i
PAINT OVERSPRAY REMOVAL EFFICIENCY % oe
IN nnn oa
PAINT OVERSPRAY REMOVAL EFFICIENCY % Rie
Ba oe :
2ST ee
90
400 500 750 2000
WEIGHT PAINT FED (grams)
f
*Actual test report available upon request.

38FILTPA22A_TDS.pdf

Sat, 27 Sep 2025 10:06:59 +0000

38FILTF2A_TDS.pdf

Sat, 27 Sep 2025 10:06:58 +0000

THE WORLD LEADER IN CLEAN AIR SOLUTIONS
% /
FIBERGLASS PAINT ARRESTOR PADS er ) : ee
* Effectively removes paint overspray Open Weave Fiber Pattern Z (~ i a Bis sie, f
solids of all types lacquer, air dry, Holds More Paint / ae =
or baked enamel AG-28 pads are designed = & = | |
exclusively to collect paint be 2 wl | aly
* Protects exhaust ducts, fans, and overspray. They are made from is no
motors from paint buildup continuous filament glass fibers 2 ~ kas
with an open weave pattern that is vas LI
* Clean exhaust air is discharged to allows particles to penetrate deep
the atmosphere into the pad. Paint is collected throughout the full depth, extending pad life and
reducing costs. A skin backing on the air leaving side serves as a final barrier to
Economical to use prevent paint and other coatings from penetrating through the media.
Smooth Airflow Through Booth Prevents Fogging
A specially formulated thermoset resin provides high compression strength,
Lightly Loaded Air preventing AG-28 pads from collapsing and face-loading as they become
Entering Side
Close-up photo saturated. Air continues to flow smoothly through the pads, preventing
shows open weave fogging or misting of paint particles in the booth. Overspray is drawn into
pattern that allows the pads so that it does not settle on spray guns, walls, floors, or conveyors.
overspray to Proper airflow ensures healthier working conditions in conformance to
penetrate deep into
the pad. OSHA standards.
Heavily Loaded Alr Cleaner Exhaust Air Fewer Maintenance,
Entering Side Environmental Problems
ores ooedoad Continuous filament glass fibers force paint laden air to change directions
illustrates the large many times as it passes through the pad. Paint particles, unable to follow the
holding capacity of continuously weaving air stream, collect on the fibers. Cleaner exhaust air flows
each fiber. The open on through
space between 9h.
Bers continues to Maintenance problems and the hazards of fire are reduced because fans,
eri airflo
ae stows panto motors, and ducts do not accumulate layers of paint. Cleaner air is discharged
penetrate. to the atmosphere, protecting the local environment from unintentional
dusting and costly property damage.
Heavily Loaded
Groas-Section Fast, Easy Installation and Removal
Cross-section view
shows how the An entire bank of AG-28 pads can be changed in a few minutes. They fit into
aon Sized standard holding frames, with no new grids or other accessories needed.
by collecting paint AG-28 pads are directly interchangeable with other types of paint arrestors.
throughout the full Only one AG-28 pad is required per frame, including installations where two
depth, paper pads are currently used.
ADF Flondow

38FILT330_TDS.pdf

Sat, 27 Sep 2025 10:06:56 +0000

WINNIHt ”
i” |
ALF MTT uu | |
omoxmannexs Better Air is Our Business
AmericanAirFilter a ;
AmerSeal ae a
oe ae
Self Sealing, Internal Wire Frame Pict as 5
Ring and Link Panel Filters a
* Three models: Gold (4-ply); Blue (3-ply), Green (2-ply) 4 q 4
+ All models available with antimicrobial a9 a
* Self-sealing design provides fast and easy installation Ly 4 5
requiring no clips or latches * ig
+ Leak free, no dirty air bypass . ay 4 Le –< * Moisture resistant, polyester media : ~~ + MERV 8 ~ Saves on Shipping and Storage AmerSeal self-sealing, ring and link panel filters are available The AmerSeal filter design reduces the cost of shipping and storage, in Gold (4-ply), Blue (3-ply), and Green (2-ply) designs. when compared to conventional filters with cardboard frames. As a AmerSeal filters offer unitized construction. Layers of AmerSeal result, using AmerSeal filters can mean fewer trips to air handlers for filter media are sealed around the entire perimeter of the filter, maintenance personnel and smaller boxes to handle. and at various points on the face, to bond the wire frame inside the layers of media. The entire assembly is designed for dependable, . trouble-free operation. Consistency of Performance AAF's refined manufacturing processes ensure consistency of performance for every AmerSeal filter. This consistency means JAQ Enhanced Performance that you will have filtration you can count on each time you insert All AmerSeal filters are available with antimicrobial. The antimicrobial a0 AmerSeal filter into your HVAC system. is effective in restricting the spread of microbes known to affect Indoor AF is dedicated to continually improving IAQ. For more than 90 years, Air Quality (IAQ). Used on AmerSeal filter media, the antimicrobial our slogan has been Better Air is Our Business. That experience and helps preserve the integrity of the filter throughout its useful life by knowledge are incorporated into every AmerSeal filter you purchase. limiting the proliferation of microbes it contacts. Link Panels Link panels are used primarily in side access systems where the entire link can be easily inserted into, and removed from, the channel as a single unit. No extended reaching or struggling with special removal devices. Fast and simple filter changing saves maintenance cost and time. Also, the continuous link design eliminates bypass between filters which can allow unfiltered air to enter the system.

38FILT300_TDS.pdf

Sat, 27 Sep 2025 10:06:55 +0000

38FILT-F-5_TDS.pdf

Sat, 27 Sep 2025 10:06:54 +0000

THE WORLD LEADER IN CLEAN AIR SOLUTIONS
Roll-O-Mat =

AUTOMATIC ROLL FILTER MEDIA
Roll-O-Mat Gold Premium Quality Roll-O-Mat filter media were
Roll-O-Mat Gold media provides a developed for use in Roll-O-Matic
combination of high performance and strength. automatic renewable media air filters.
2 thick media of continuous filament Available in roll widths to fit all filter
sizes and all manufacturers filters,
fiberglass –
oH Sl Vi adhesi Roll-O-Mat media continues to be
leavy application of Viscosine adhesive the most widely used and most
* Rolls are 65′ long dependable brand in the industry.
* Gold tint on air leaving side
Designed for Dependable Performance
|-O-Mat i
Roll o-Mat Green Synthetic sat High Fiber Content
hone wiht a oe ee a ications Roll-O-Mat Gold media has more glass fibers, more than 8% miles
where a synthetic media is preferred. per square foot, than any competitive media. Higher fiber content
* 100% polyester fibers provides more dirt catching media surface, providing higher arrestance
* Available 2″ and 1 thick and greater dust holding capacity.
* Medium application of Viscosine adhesive High Compression Strength Extends Filter Life
Rolls are 65 long Resin applied to the fiberglass during spinning is cured in an oven to
* Green tint on air leaving side form a strong bond at each fiber intersection. Bonded fibers increase
compression strength and prevent faceloading. Air moves throughout
the entire thickness of the media utilizing the full cleaning potential of
the media.
Progressive Density Increases Arrestance
Fibers on the air entering side are interlaced in an open pattern
that becomes progressively tighter. Dirt loads from back to front,
taking advantage of the entire thickness of the media. This
construction prevents faceloading and increases arrestance and
dust holding capacity.
4 i
W)04)’)) Zz
; i
ie).
Gera Airtlow
(( (4) aw
A AMS .
; Ne _ Progressive Density
U u Media Construction
ADF Flondow

38FILFT1A_TDS.pdf

Sat, 27 Sep 2025 10:06:53 +0000

38DRHEATER_TDS.pdf

Sat, 27 Sep 2025 10:06:53 +0000

Industrial Process Heaters PLN
Silicone Rubber Drum Heaters F .
Made in USA
Silicone Rubber Drum and Pail Heaters
Fi Design Features
Built tough 9g . .
: ~ * Maximum operating temperature
. . of 425 F (218 C).
Resistant to chemicals * Power cord is 6-foot long, SJO Type 16/3
4 j complete with three-prong plug for 120 VAC
; oman Ratings for Metal and models. Plugs are not included on 240 VAC
Plastic Drums and Pails models but are available (see page 15-15).
~ * Surface grounded electrically with internal
4 wy * 1250 volts dielectric tested.
y r . * Vulcanized silicone rubber construction
Stock to 2 week lead time resistant to moisture, ozone, fungus, and
; / radiation.
UL and CSA Approval * Adjustable thermostat, see page 9-16 for
See page 9-2 for details specifications.
Tempco flexible drum heaters can save time by heating stored viscous fluid
4 to a pourable temperature.
The heater is built to be tough, long lasting, and resistant to chemicals. Because few
materials stick to its silicone rubber with fiberglass reinforced construction, it is
easy to clean. The heater comes with a 6-foot cord and plug (120V only). When not
in use, it rolls for convenient storage.
The total wattage (number of heaters) and the material being heated inside of the
drum must be considered when determining the actual temperature to which that
specific material can be heated.
Standard (Non-Stock) and Stock Drum Heaters for Metal Drums
| Stock Items Are Shown In RED
250 Ambient Temperature 60 F _| Heater [Heater as
i i jeater | Hea art Number
40 Pram filed with water | =I Peo [eS] Width = 420V 240V
230 =! 5Gal. | 15 | 3″ 31″ | 300 | DHR00150 | DHR01010 | 50-425 F
220 L{ Ty ttt tt Perr 15Gal. | 13.5 | 3″ 38″ | 500 | DHROOI10 | DHROO130 | 50-425 F
See 30Gal.} 18 | 3″ | 52″ | 750 | DHR00070 | DHR00090 | 50-425 F
210 rEEELELI LL 55 Gal. | 22.5 | 3″ 64″ __| 1000 | DHR00020 | DHR00040 | _50-425 F
4 200 WA 5Gal. | 1s | 3″ 31″ | 300 | DHR0O140 | DHRO1041 No
190 LETT TTA Tt Tt ey 15Gal. | 13.5 | 3″ 38″ | 500 | DHROO100 | DHROO120 No
2. | [TTI [ 2 theaters | 30Gal. | 18 3″ 52″ | 750 | DHR00060 | DHROOO8O No
2 Heat
180 fm 55Gal. | 225 | 3″ | 64″ | 1000 | DHR00010 | DHR00030 No
= 170 Be? -S55 5Gal. | 115 | 4″ 31″ | 550 | DHROI014 | DHROIOI8 | 50-425 F
evo +} TVET TT TY 15Gal.| 135 | 4″ 38″ | 700 | DHROI013 | DHROIOI7 | 50-425 F
5 160
zio- LIAYLTT TTT TI 30Gal.| 18 | 4″ | 52″ | 1000) DHROI012 | DHROI016 | 50-425 F
55Gal. | 225 | 4″ 64″ | 1500 | DHR00050 | DHR000SS | _50-425 F
nn) 4ee mS :
a TL ITVLELLLLL [thester | 5Gal. | 115 | 95 31″ | 1000 | DHRO1023 | DHRO1047 | 70-190 F
130 ae 15Gal. | 13.5 | 95″ | 38″ | 1000 DHRO1024 | DHRO1046 | 70-190 F
wt _t_ WIT err 55 Gal. | 22.5 | 95″ | 64″ | 1500 | DHRO1025 | DHRO1045 | 70-190 F
TTT et LL
400 LIA TAT TTT tty Standard (Non-Stock) and Stock Drum Heaters for Plastic Pails
wo lIZ TT TTT Tt TT Stock Items Are Shown In RED
of AAT Tt Tt Tt Heater |Heswr Part Number
wYAt tT ttt tt tt ty Width Length 420V 240V__| Thermostat
60 VITTTTTtTtr tt th 5Gal. | 115 | 4″ 31″ | 150 | DHRO1034 | DHRO1044 | 50-160 F
0 2 4 6 8 10 12 14 16 18 20 22 24 15Gal. | 13.5 | 4″ 38″ | 200 | DHRO1035 | DHRO1036 | 50-160 F
Time in Hours 30Gal.| 18 | 4″ 52″ | 250 | DHRO1037 | DHRO1038 | 50-160 F
55Gal. | 225 | 4″ 64″__| 300 | DHR01033 | DHR01039 | _50-160 F
5Gal. | 115 | 95″ | 31″ | 300 | DHRO1027 | DHRO1043 | 70-140 F
55Gal. | 225 | 95″ | 64″ | 750 | DHR01026 | DHRO1042 | 70-140 F
Standard lead time is Stock to 2 weeks.
41-120 View Product Inventory @ www.tempco.com
–

38CLAY221_TDS.pdf

Sat, 27 Sep 2025 10:06:52 +0000

yber
(866) 260-6457 Ory
Tooling Waxes & Clays www.Rjmarshall.com tude
rr
Tooling Wax & Clay
Rhino Extrudable Wax Tooling Wax Saas
Cast polymer manufacturers have long recognized the benefits Tooling Wax is used to create a smooth [Jap
of using wax fillets in setting up molds for production. The _radius between the edge of a floating bowl Sy
smooth radii and ease of finishing from wax provide significant _ mold and the surface of the vanity deck on –
benefits to the user compared to clay. Gruber Supplies & which it is positioned. Available in a 1b a 4
Accessories has developed an extrudable wax that combines the roll, 2Ib boxes and case quantities. –
flexibility of clay and the quality of wax. Our wax is available
in 5 x 1 sticks. Order Information
#1 – 1/16 – 1b Roll – #01037
Order Information bee uae #1 – 1/16 – 2lb Roll – #01038
Ex-hard 2lb box – #SP1018 Bek #2 – 1/8 1 Ib Roll – #01039
Ex-hard 24lb case – #SP1019. | #2 – 1/8 – 2Ib Box – #01040
Hard 2b box – #SP1020 Hee | #2 – 1/8 – 2Ib – Case of 20 Rolls – #010400
Hard 24lb case – #SP1021 ang) a #3 – 3/16 – lb Roll – #01041
Soft 2lb box – #SP1022 #3 – 3/16 – 2lb Box – #01042
Soft 24lb case – #SP1023 ee #3 – 3/16″ – 2lb – Case of 20 Rolls – #010420
Ex-Soft 2lb box – #SP1024 perme
Ex-Soft 24lb case – # SP1025 . EX-Wax
. This Gruber Supplies & Accessories extrudable fillet material
Tooling Clay offers the best characteristics of both fillet wax and modeling
Tooling Clay is used for the same purposes as Ex-Wax and clay. EX-Wax leaves a smooth radius, doesn t contain solvents,
Tooling Wax – to create a smooth radius between the edge ofa _ tools easily and is extrudable. A box contains 12 sticks and
floating bowl mold and the surface of the vanity deck on which _ weighs 2Ibs. A case contains 12 boxes of 12 sticks each, or 144
itis positioned. Like Ex-Wax, no special pps total sticks.
applicator tools or heat are required | (== ==
in its use. The clay can be extruded in of i Order Information
the size required through the Clay/ =~ Super Extra Soft – Case/12 Boxes – #02218
Wax Extruder. Packaged in 20 stick – eo Fite Sy Soft – Case/12 Boxes – #02214
Slb boxes or 200 stick – 50lb boxes of |= Ste > Hard – Case/12 Boxes – #02216
individually wrapped 4 oz sticks. = DuraHard – Case/12 Boxes – #02219
Super Soft – Box/12 Sticks – #02223
Order Information Soft – Box/12 Sticks – #02213
Tooling Clay Soft – 5lb Box – #02209A. Hard – Box/12 Sticks – #02215
Tooling Clay Soft – 501b Case – #02210A, DuraHard – Box/12 Sticks – #02220
Tooling Clay Hard – 5lb Box – #02209
Tooling Clay Hard – 50Ib Case – #02210
Applicators & Accessories
Waxing (Radius) Tools Clay/Wax Extruder s |
Create a smooth, clean wax radius around the edge of your & Parts Bist res = fh
mords en a deck surface with these handy, simple, radius hand The Pneumatic or Manual & oo ~ oe 4
tools that worl Clay Extruder offers a | :
convenient way to quickly Aug see
create an exacting bead of = ay
q 3 wax or clay for mold setup. RE ae Bee
Order Information Order Information edt
#1 (1/4-1/8 Radius) – Ea – #01031 I Manual Extruder – Ea – #100005
#2 (1/2-3/8 Radius) – Ea – #01032 Pneumatic Extruder – Ea – #100017
#3 (3/4-5/8 Radius) – Ea – #01033 f Related Accessories:
Kit, Nozzle, Clay Extruder (Set/3) – #100012
Clay Extruder Light Bulb – Ea – #100013
z Pneumatic Extruder Teflon Scraper – Ea – #100021
Pneumatic Clay Extruder Tube – Ea – #1000214
-16- Rev. 2

38CLAY221I_TDS.pdf

Sat, 27 Sep 2025 10:06:51 +0000

38CLAY221A_TDS.pdf

Sat, 27 Sep 2025 10:06:50 +0000

38ASR3_TDS.pdf

Sat, 27 Sep 2025 10:06:49 +0000

5700 Skylab Road Phone : +1 714-899-8100 E-mail : airtech@airtech.com
f loa Huntington Beach Fax: +1 714-899-8179 Website : www.airtech.com
INTERNATIONAL INC. CA 92647 USA
Data Sheet AIRSWEEP R2 & R3
Composite laminating tools for prepregs and fabrics
DESCRIPTION
Airsweep R2 & R3 are composite laminating tools for placement of prepregs and fabrics onto molds. Airsweep.
R2 & R3 have been ergonomically designed to fit the hand more comfortably, so even pressure can be applied
into sharp corners easily with reduced operator fatigue. These products are manufactured from abrasion
resistant non-contaminating UHMW PE and nylon.
@ BENEFITS
+ Apply even pressure accurately to tight corners to eliminate fabric bridging and avoid part rework.
+ Handle design applies palm pressure, reducing finger fatigue.
+ Non-contaminating material avoids FOD in layups.
@ ~ TECHNICAL DATA
. R2: UHMW PE, Natural color
Material type R3: Nylon, Black color
@ SIZES
R2 &R3 0.36 in (9.2 mm) 4.5 in (115 mm) 1.0 in (25 mm)
Airsweep R2 Airsweep R3
@ NOTES
+ Minimum order quantity: 1 each
+ The UHMW PE material in Airsweep R2 conforms to ASTM D4020-011.
+ The nylon 6/6 material in Airsweep R3 conforms to ASTM D4066 and ASTM D5989.
Last updated : 2023-06-28
Catalog position : Miscellaneous A
-Asthecondton or methods fuse, including storage ae beyond our control Altech tration nc does ot sme any responsi fe the performance of his material fo any para ue. The mater sold” A
Artech eration ne dclsne and buyer waive, any analimpled warantesincidg without mtn the pled warns of merchant and of ness fo pata use. The formation contaned heen A
eer ete eae at eet om ee ree Rea cre ee We eT I A

383M72593_TDS.pdf

Sat, 27 Sep 2025 10:06:48 +0000

Paper or plastic?
The choice is clear.
Prep with plastic it s better than masking paper
*
.
Features and benefits:
Waterproof: not affected by rain,
dew or washwater
No paint bleed-through
Paint-flake resistant
Easy to wrap around objects
Translucent allows light to shine through
2X more per roll
*
Your reputation depends on high-quality results.
But your bottom line depends on saving time and
money. Get the best of both with 3M

Hand-Masker

Masking Plastic. This product resists bleed-through
better than 3M

Hand-Masker

General Purpose
Masking Paper. It s water and flake resistant, easy to
wrap around objects and translucent, allowing light in.
Plus, you get 2X more product per roll.
*
When used with
the 3M

Hand-Masker

M3000 Dispenser, it all adds
up to a faster, easier prep process for you and better
results for your customer.
Billing UPC Consumer UPC Shipper UPC Product # Product Description Pack/Case
000-76308-72594-5 000-76308-72594-5 500-76308-72594-0 MPL6
3M

Hand-Masker

Masking Plastic MPL6, 6 in x 120 yd
(15.2 cm x 109 m)
12/case
000-76308-72595-2 000-76308-72595-2 500-76308-72595-7 MPL9
3M

Hand-Masker

Masking Plastic MPL9, 9 in x 120 yd
(22.8 cm x 109 m)
12/case
000-76308-72593-8 000-76308-72593-8 500-76308-72593-3 MPL12
3M

Hand-Masker

Masking Plastic MPL12, 12 in x 120 yd
(30.4 cm x 109 m)
12/case
Please recycle. Printed in U.S.A. 3M 2016.
All rights reserved. 3M, Hand-Masker and the
BLUE color of the tape are trademarks of 3M.
Construction and Home Improvement Markets Division 3M Center, Building 223-4S-02, St. Paul, MN 55144-1000
1-800-494-3552 3M.com/HandMasker
70-0717-2240-2
*Compared to 3M

Hand-Masker

General Purpose Masking Paper.

Pl stico o papel?
La opci n es clara.
Prepare con pl stico es mejor que el papel de enmascarar
*
.
Su reputaci n depende de los resultados de alta calidad. Pero
sus resultados finales dependen de ahorrar tiempo y dinero.
Consiga los mejores resultados con el Pl stico de Enmascarar
3M

Hand-Masker

. Este producto resiste las filtraciones
mejor que el Papel de Enmascarar de Uso General 3M

Hand-Masker

. Es resistente al agua y al descascaramiento,
f cil de manipular para envolver alrededor de los objetos, y
transl cido, lo que permite que pase la luz. Adem s, obtiene
2 veces m s de producto por rollo
*
. Cuando se lo utiliza con
el Dispensador 3M

Hand-Masker

M3000 el proceso se
vuelve m s r pido y f cil para usted, y los resultados son
mejores para su cliente.
UPC de Facturaci n UPC de Consumidor UPC de Cart n # Producto Descripci n del Producto Paquetes/Caja
000-76308-72594-5 000-76308-72594-5 500-76308-72594-0 MPL6
Pl stico de Enmascarar 3M

Hand-Masker

MPL6,
6 in x 120 yd (15.2 cm x 109 m)
12/caja
000-76308-72595-2 000-76308-72595-2 500-76308-72595-7 MPL9
Pl stico de Enmascarar 3M

Hand-Masker

MPL9,
9 in x 120 yd (22.8 cm x 109 m)
12/caja
000-76308-72593-8 000-76308-72593-8 500-76308-72593-3 MPL12
Pl stico de Enmascarar 3M

Hand-Masker

MPL12,
12 in x 120 yd (30.4 cm x 109 m)
12/caja
Por favor, recicle. Impreso en E.U.A. 3M 2016. Todos los derechos reservados. 3M, Hand-Masker y el color AZUL de la cinta son marcas registradas de 3M.
Construction and Home Improvement Markets Division 3M Center, Building 223-4S-02, St. Paul, MN 55144-1000
1-800-494-3552 3M.com/HandMasker
70-0717-2240-2
*En comparaci n con el Papel de Enmascarar de Uso General 3M

Hand-Masker.

Caracter sticas y beneficios:
Impermeable: no lo afecta la lluvia, el roc o ni
el agua de lavado
Sin filtraciones de pintura
Resistente al descascaramiento de pintura
F cil para envolver objetos
Transl cido (permite que pase la luz)
2 veces m s por rollo
*

3829865_TDS.pdf

Sat, 27 Sep 2025 10:06:46 +0000

Subject: FW: TECH DATA SHEET 29-865 FLOOR PAPER 60″ 80LB FLAME-A-GUARD III FR
Attachments: SDS-26 Flame-a-guard booth papers (29-843, 29-844, 29-863, 29-864, 29-865, 29-866,
29-872, 29-873, 29-874, and 29-875).pdf
From: Binks Tech Support
Sent: Friday, February 14, 2025 10:58 AM
To: Ask Binks
Subject: RE: TECH DATA SHEET 29-865 FLOOR PAPER 60″ 80LB FLAME-A-GUARD III FR
Caution! This message was sent from outside your organization. Allow sender | Block sender | Report

Flame-A-Guard I|II Flame Retardant Paper
Spray Booth Floor Paper a
* Compliant with NFPA 33 <<: fae <>
3 D vie
+ Provides quick, economical compliance ea: 72 f aa
with OSHA requirements rf. iP, (i
* White – improves booth visibility 2 ae ee A
. rapes will char but will not propagate
FLAME-A-GUARD III FLAME RETARDANT PAPER
+ Allows fast and easy booth clean-up – no
scraping, stripping or scrubbing Jpstno. / DESCRIPTION
+ Lint free 70 LB. Foot Traffic | 29-843 White, 36 x 500″
+ Eliminates tracking paint from spray | 29-844 White, 72 x S00″
booth to other plant areas 80 LB. Heavler Traffic 29-863, White, 36″ x 300
* Rolls are individually boxed for easy 29-864 White, 42 x 300
storage and shipping 29-865 White, 60 x 00
+ Increases plant efficiency and reduces 29-866 White, 72 x 300
clean-up and shutdown costs ;

100 LB. Fork Lift Traffic 29-872 White, 36 x 300
| 29-875 White, 42 x 300
| 29-873 White, 60 x 300
| 29-874 White, 72 x 300